diff mbox series

[v2,2/5] arm64: dts: meson: fix PHY deassert timing requirements

Message ID fe0fb54d4c7b99fb148954c1c9a8b1902c2b7b9c.1606828668.git.stefan@agner.ch (mailing list archive)
State New, archived
Headers show
Series [v2,1/5] arm64: dts: meson: g12b: odroid-n2: fix PHY deassert timing requirements | expand

Commit Message

Stefan Agner Dec. 1, 2020, 1:21 p.m. UTC
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
egisters. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
  [ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
  [ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
  [ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
  [ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
  [ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed

Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
 arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts  | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts   | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi  | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi     | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts  | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts   | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts        | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts    | 2 +-
 9 files changed, 9 insertions(+), 9 deletions(-)

Comments

Martin Blumenstingl Dec. 5, 2020, 1:14 p.m. UTC | #1
On Tue, Dec 1, 2020 at 2:21 PM Stefan Agner <stefan@agner.ch> wrote:
>
> According to the datasheet (Rev. 1.9) the RTL8211F requires at least
> 72ms "for internal circuits settling time" before accessing the PHY
> egisters. This fixes an issue seen on ODROID-C2 where the Ethernet
> link doesn't come up when using ip link set down/up:
>   [ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
>   [ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
>   [ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
>   [ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
>   [ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
>
> Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
> Signed-off-by: Stefan Agner <stefan@agner.ch>
with the "registers" typo above fixed:
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index 7be3e354093b..de27beafe9db 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -165,7 +165,7 @@  eth_phy0: ethernet-phy@0 {
 			reg = <0>;
 
 			reset-assert-us = <10000>;
-			reset-deassert-us = <30000>;
+			reset-deassert-us = <80000>;
 			reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 			interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 70fcfb7b0683..50de1d01e565 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -200,7 +200,7 @@  eth_phy0: ethernet-phy@0 {
 			reg = <0>;
 
 			reset-assert-us = <10000>;
-			reset-deassert-us = <30000>;
+			reset-deassert-us = <80000>;
 			reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 			interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
index 222ee8069cfa..9b0b81f191f1 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
@@ -126,7 +126,7 @@  eth_phy0: ethernet-phy@0 {
 			reg = <0>;
 
 			reset-assert-us = <10000>;
-			reset-deassert-us = <30000>;
+			reset-deassert-us = <80000>;
 			reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 			interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
index ad812854a107..a350fee1264d 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
@@ -147,7 +147,7 @@  eth_phy0: ethernet-phy@0 {
 			reg = <0>;
 
 			reset-assert-us = <10000>;
-			reset-deassert-us = <30000>;
+			reset-deassert-us = <80000>;
 			reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 			interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
index b08c4537f260..b2ab05c22090 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
@@ -82,7 +82,7 @@  external_phy: ethernet-phy@0 {
 
 		/* External PHY reset is shared with internal PHY Led signal */
 		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
+		reset-deassert-us = <80000>;
 		reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 		interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
index bff8ec2c1c70..e38d9e50caa7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
@@ -194,7 +194,7 @@  external_phy: ethernet-phy@0 {
 		reg = <0>;
 
 		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
+		reset-deassert-us = <80000>;
 		reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 		interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
index 83eca3af44ce..dfa7a37a1281 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
@@ -112,7 +112,7 @@  external_phy: ethernet-phy@0 {
 		max-speed = <1000>;
 
 		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
+		reset-deassert-us = <80000>;
 		reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 	};
 };
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
index ea45ae0c71b7..8edbfe040805 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
@@ -64,7 +64,7 @@  external_phy: ethernet-phy@0 {
 
 		/* External PHY reset is shared with internal PHY Led signal */
 		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
+		reset-deassert-us = <80000>;
 		reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 		interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
index c89c9f846fb1..dde7cfe12cff 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
@@ -114,7 +114,7 @@  external_phy: ethernet-phy@0 {
 		max-speed = <1000>;
 
 		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
+		reset-deassert-us = <80000>;
 		reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 	};
 };