[V8,0/8] Add QSPI and QUPv3 DT nodes for SC7280 SoC

Message

Rajesh Patil Sept. 17, 2021, 9:47 a.m. UTC

Changes in V8:
 - As per Matthias comments 
   Added qup_spiN_cs_gpio nodes in all spi ports

 - As per Doug comments, Added "qcom,sc7280-qspi" compatible in qspi node

Changes in V7:
 - As per Stephen's comments
   1. Moved qup_opp_table under /soc@0/geniqup@9c0000
   2. Removed qupv3_id_1 in sc7280-idp board file
   3. Sorted alias names for i2c and spi as per alphabet order

 - As per Matthias comment
   Configuring cs pin with gpio (qup_spiN_cs_gpio) definitions are removed

Changes in V6:
 - As per Matthias' comments,
   1. Squashed "Update QUPv3 UART5 DT node" and "Configure debug 
      uart for sc7280-idp"
   2. Moved qup_opp_table from /soc to /
   3. Changed convention "clocks" followed by "clock-names"

 - As per Doug comments, added aliases for i2c and spi

Changes in V5:
 - As per Matthias' comments, I've split the patches as below:
   1. Add QSPI node
   2. Configure SPI-NOR FLASH for sc7280-idp
   3. Add QUPv3 wrapper_0 nodes
   4. Update QUPv3 UART5 DT node
   5. Configure debug uart for sc7280-idp
   6. Configure uart7 to support bluetooth on sc7280-idp
   7. Add QUPv3 wrapper_1 nodes

Changes in V4:
 - As per Stephen's comment updated spi-max-frequency to 37.5MHz, moved
   qspi_opp_table from /soc to / (root).
 - As per Bjorn's comment, added QUP Wrapper_0 nodes
   as separate patch and debug-uart node as separate patch.
 - Dropped interconnect votes for wrapper_0 and wrapper_1 node
 - Corrected QUP Wrapper_1 SE node's pin control functions like below
        QUP Wrapper_0: SE0-SE7 uses qup00 - qup07 pin-cntrl functions.
        QUP Wrapper_1: SE0-SE7 uses qup10 - qup17 pin-cntrl functions.

Changes in V3:
 - Broken the huge V2 patch into 3 smaller patches.
   1. QSPI DT nodes
   2. QUP wrapper_0 DT nodes
   3. QUP wrapper_1 DT nodes

Changes in V2:
 - As per Doug's comments removed pinmux/pinconf subnodes.
 - As per Doug's comments split of SPI, UART nodes has been done.
 - Moved QSPI node before aps_smmu as per the order.

Rajesh Patil (4):
  dt-bindings: spi: add QSPI bindings for sc7280 chipset
  arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp
  arm64: dts: sc7280: Configure uart7 to support bluetooth on sc7280-idp
  arm64: dts: sc7280: Add aliases for I2C and SPI

Roja Rani Yarubandi (4):
  arm64: dts: sc7280: Add QSPI node
  arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
  arm64: dts: sc7280: Update QUPv3 UART5 DT node
  arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes

 .../bindings/spi/qcom,spi-qcom-qspi.yaml           |    5 +-
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi           |  125 +-
 arch/arm64/boot/dts/qcom/sc7280.dtsi               | 3216 +++++++++++++++-----
 3 files changed, 2520 insertions(+), 826 deletions(-)