[v6,0/4] Introduce PMIC based USB type C detection

Message

Wesley Cheng July 29, 2020, 7:13 a.m. UTC

Changes in v6:
 - Removed qcom_usb_vbus-regulator.c and qcom,usb-vbus-regulator.yaml from the
   series as they have been merged on regulator.git
 - Added seperate references to the usb-connector.yaml in qcom,pmic-typec.yaml
   instead of referencing the entire schema.

Changes in v5:
 - Fix dt_binding_check warning/error in qcom,pmic-typec.yaml

Changes in v4:
 - Modified qcom,pmic-typec binding to include the SS mux and the DRD remote
   endpoint nodes underneath port@1, which is assigned to the SSUSB path
   according to usb-connector
 - Added usb-connector reference to the typec dt-binding
 - Added tags to the usb type c and vbus nodes
 - Removed "qcom" tags from type c and vbus nodes
 - Modified Kconfig module name, and removed module alias from the typec driver
 
Changes in v3:
 - Fix driver reference to match driver name in Kconfig for
   qcom_usb_vbus-regulator.c
 - Utilize regulator bitmap helpers for enable, disable and is enabled calls in
   qcom_usb_vbus-regulator.c
 - Use of_get_regulator_init_data() to initialize regulator init data, and to
   set constraints in qcom_usb_vbus-regulator.c
 - Remove the need for a local device structure in the vbus regulator driver
 
Changes in v2:
 - Use devm_kzalloc() in qcom_pmic_typec_probe()
 - Add checks to make sure return value of typec_find_port_power_role() is
   valid
 - Added a VBUS output regulator driver, which will be used by the PMIC USB
   type c driver to enable/disable the source
 - Added logic to control vbus source from the PMIC type c driver when
   UFP/DFP is detected
 - Added dt-binding for this new regulator driver
 - Fixed Kconfig typec notation to match others
 - Leave type C block disabled until enabled by a platform DTS

Add the required drivers for implementing type C orientation and role
detection using the Qualcomm PMIC.  Currently, PMICs such as the PM8150B
have an integrated type C block, which can be utilized for this.  This
series adds the dt-binding, PMIC type C driver, and DTS nodes.

The PMIC type C driver will register itself as a type C port w/ a
registered type C switch for orientation, and will fetch a USB role switch
handle for the role notifications.  It will also have the ability to enable
the VBUS output to any connected devices based on if the device is behaving
as a UFP or DFP.

Wesley Cheng (4):
  usb: typec: Add QCOM PMIC typec detection driver
  dt-bindings: usb: Add Qualcomm PMIC type C controller dt-binding
  arm64: boot: dts: qcom: pm8150b: Add node for USB type C block
  arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster

 .../bindings/usb/qcom,pmic-typec.yaml         | 131 +++++++++
 arch/arm64/boot/dts/qcom/pm8150b.dtsi         |  15 +-
 arch/arm64/boot/dts/qcom/sm8150-mtp.dts       |   4 +
 drivers/usb/typec/Kconfig                     |  12 +
 drivers/usb/typec/Makefile                    |   1 +
 drivers/usb/typec/qcom-pmic-typec.c           | 275 ++++++++++++++++++
 6 files changed, 437 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml
 create mode 100644 drivers/usb/typec/qcom-pmic-typec.c