| Message ID | 20210517200907.1459182-1-dianders@chromium.org (mailing list archive) |
|---|---|
| Headers | show |
| Series | drm: Fix EDID reading on ti-sn65dsi86 by introducing the DP AUX bus | expand |
JFYI I haven't had a chance yet but I'm hoping to look at this this week On Mon, 2021-05-17 at 13:08 -0700, Douglas Anderson wrote: > The primary goal of this series is to try to properly fix EDID reading > for eDP panels using the ti-sn65dsi86 bridge. > > Previously we had a patch that added EDID reading but it turned out > not to work at bootup. This caused some extra churn at bootup as we > tried (and failed) to read the EDID several times and also ended up > forcing us to use the hardcoded mode at boot. With this patch series I > believe EDID reading is reliable at boot now and we never use the > hardcoded mode. > > High level note: in this series the EDID reading is driven by the > panel driver, not by the bridge chip driver. I believe this makes a > reasonable amount of sense since the panel driver already _could_ > drive reading the EDID if provided with the DDC bus and in future > planned work we'll want to give the panel driver the DDC bus (to make > decisions based on EDID) and the AUX bus (to control the > backlight). There are also planned patches from Laurent to make > ti-sn65dsi86 able to drive full DP monitors. In that case the bridge > chip will still be in charge of reading the EDID, but it's not hard to > make this dynamic. > > This series is the logical successor to the 3-part series containing > the patch ("drm/bridge: ti-sn65dsi86: Properly get the EDID, but only > if refclk") [1]. > > This patch was tested against drm-misc-next commit 60a6b73dd821 > ("drm/ingenic: Fix pixclock rate for 24-bit serial panels") on a > sc7180-trogdor-lazor device. > > At v7 now, this patch series grew a bit from v6 because it introduces > the DP AUX bus. > > Between v2 and v3, high-level view of changes: > - stop doing the EDID caching in the core. > > Between v3 and v4, high-level view of changes: > - EDID reading is actually driven by the panel driver now. See above. > - Lots of chicken-and-egg problems solved w/ sub-devices. > > Between v4 and v5, high-level view of changes. > - Some of the early patches landed, so dropped from series. > - New pm_runtime_disable() fix (fixed a patch that already landed). > - Added Bjorn's tags to most patches > - Fixed problems when building as a module. > - Reordered debugfs patch and fixed error handling there. > - Dropped last patch. I'm not convinced it's safe w/out more work. > > Between v5 and v6, high-level view of changes: > - Added the patch ("drm/dp: Allow an early call to register DDC i2c > bus") > - Many patches had been landed, so only a few "controversial" ones > left. > > Between v6 and v7, high-level view of changes: > - New AUX DP bus! > > [1] > https://lore.kernel.org/r/20210304155144.3.I60a7fb23ce4589006bc95c64ab8d15c74b876e68@changeid/ > > Changes in v7: > - pm_runtime_dont_use_autosuspend() fix new for v7. > - List hpd properties bindings patch new for v7. > - ti-sn65dsi86: Add aux-bus child patch new for v7. > - Patch introducing the DP AUX bus is new for v7. > - Patch to allow panel-simple to be DP AUX EP new for v7. > - Patch using the DP AUX for DDC new for v7. > - Remove use of now-dropped drm_dp_aux_register_ddc() call. > - Beefed up commit message in context of the DP AUX bus. > - Set the proper sub-device "dev" pointer in the AUX structure. > - Patch to support for DP AUX bus on ti-sn65dsi86 new for v7. > - Adjusted commit message to talk about DP AUX bus. > - Panel now under bridge chip instead of getting a link to ddc-i2c > > Changes in v6: > - Use new drm_dp_aux_register_ddc() calls. > > Douglas Anderson (10): > drm/panel: panel-simple: Add missing pm_runtime_dont_use_autosuspend() > calls > dt-bindings: display: simple: List hpd properties in panel-simple > dt-bindings: drm/bridge: ti-sn65dsi86: Add aux-bus child > drm: Introduce the DP AUX bus > drm/panel: panel-simple: Allow panel-simple be a DP AUX endpoint > device > drm/panel: panel-simple: Stash DP AUX bus; allow using it for DDC > drm/bridge: ti-sn65dsi86: Promote the AUX channel to its own sub-dev > drm/bridge: ti-sn65dsi86: Add support for the DP AUX bus > drm/bridge: ti-sn65dsi86: Don't read EDID blob over DDC > arm64: dts: qcom: sc7180-trogdor: Move panel under the bridge chip > > .../bindings/display/bridge/ti,sn65dsi86.yaml | 22 +- > .../bindings/display/panel/panel-simple.yaml | 2 + > arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 30 +- > drivers/gpu/drm/Kconfig | 5 + > drivers/gpu/drm/Makefile | 2 + > drivers/gpu/drm/bridge/Kconfig | 1 + > drivers/gpu/drm/bridge/ti-sn65dsi86.c | 111 ++++-- > drivers/gpu/drm/drm_dp_aux_bus.c | 322 ++++++++++++++++++ > drivers/gpu/drm/panel/Kconfig | 1 + > drivers/gpu/drm/panel/panel-simple.c | 66 +++- > include/drm/drm_dp_aux_bus.h | 57 ++++ > 11 files changed, 563 insertions(+), 56 deletions(-) > create mode 100644 drivers/gpu/drm/drm_dp_aux_bus.c > create mode 100644 include/drm/drm_dp_aux_bus.h >
For patches 5, and 6: Reviewed-by: Lyude Paul <lyude@redhat.com> This week got really busy so I wasn't able to look at the rest of them, but next week is going to be a lot less busy so I should be able to look at them then On Mon, 2021-05-17 at 13:08 -0700, Douglas Anderson wrote: > The primary goal of this series is to try to properly fix EDID reading > for eDP panels using the ti-sn65dsi86 bridge. > > Previously we had a patch that added EDID reading but it turned out > not to work at bootup. This caused some extra churn at bootup as we > tried (and failed) to read the EDID several times and also ended up > forcing us to use the hardcoded mode at boot. With this patch series I > believe EDID reading is reliable at boot now and we never use the > hardcoded mode. > > High level note: in this series the EDID reading is driven by the > panel driver, not by the bridge chip driver. I believe this makes a > reasonable amount of sense since the panel driver already _could_ > drive reading the EDID if provided with the DDC bus and in future > planned work we'll want to give the panel driver the DDC bus (to make > decisions based on EDID) and the AUX bus (to control the > backlight). There are also planned patches from Laurent to make > ti-sn65dsi86 able to drive full DP monitors. In that case the bridge > chip will still be in charge of reading the EDID, but it's not hard to > make this dynamic. > > This series is the logical successor to the 3-part series containing > the patch ("drm/bridge: ti-sn65dsi86: Properly get the EDID, but only > if refclk") [1]. > > This patch was tested against drm-misc-next commit 60a6b73dd821 > ("drm/ingenic: Fix pixclock rate for 24-bit serial panels") on a > sc7180-trogdor-lazor device. > > At v7 now, this patch series grew a bit from v6 because it introduces > the DP AUX bus. > > Between v2 and v3, high-level view of changes: > - stop doing the EDID caching in the core. > > Between v3 and v4, high-level view of changes: > - EDID reading is actually driven by the panel driver now. See above. > - Lots of chicken-and-egg problems solved w/ sub-devices. > > Between v4 and v5, high-level view of changes. > - Some of the early patches landed, so dropped from series. > - New pm_runtime_disable() fix (fixed a patch that already landed). > - Added Bjorn's tags to most patches > - Fixed problems when building as a module. > - Reordered debugfs patch and fixed error handling there. > - Dropped last patch. I'm not convinced it's safe w/out more work. > > Between v5 and v6, high-level view of changes: > - Added the patch ("drm/dp: Allow an early call to register DDC i2c > bus") > - Many patches had been landed, so only a few "controversial" ones > left. > > Between v6 and v7, high-level view of changes: > - New AUX DP bus! > > [1] > https://lore.kernel.org/r/20210304155144.3.I60a7fb23ce4589006bc95c64ab8d15c74b876e68@changeid/ > > Changes in v7: > - pm_runtime_dont_use_autosuspend() fix new for v7. > - List hpd properties bindings patch new for v7. > - ti-sn65dsi86: Add aux-bus child patch new for v7. > - Patch introducing the DP AUX bus is new for v7. > - Patch to allow panel-simple to be DP AUX EP new for v7. > - Patch using the DP AUX for DDC new for v7. > - Remove use of now-dropped drm_dp_aux_register_ddc() call. > - Beefed up commit message in context of the DP AUX bus. > - Set the proper sub-device "dev" pointer in the AUX structure. > - Patch to support for DP AUX bus on ti-sn65dsi86 new for v7. > - Adjusted commit message to talk about DP AUX bus. > - Panel now under bridge chip instead of getting a link to ddc-i2c > > Changes in v6: > - Use new drm_dp_aux_register_ddc() calls. > > Douglas Anderson (10): > drm/panel: panel-simple: Add missing pm_runtime_dont_use_autosuspend() > calls > dt-bindings: display: simple: List hpd properties in panel-simple > dt-bindings: drm/bridge: ti-sn65dsi86: Add aux-bus child > drm: Introduce the DP AUX bus > drm/panel: panel-simple: Allow panel-simple be a DP AUX endpoint > device > drm/panel: panel-simple: Stash DP AUX bus; allow using it for DDC > drm/bridge: ti-sn65dsi86: Promote the AUX channel to its own sub-dev > drm/bridge: ti-sn65dsi86: Add support for the DP AUX bus > drm/bridge: ti-sn65dsi86: Don't read EDID blob over DDC > arm64: dts: qcom: sc7180-trogdor: Move panel under the bridge chip > > .../bindings/display/bridge/ti,sn65dsi86.yaml | 22 +- > .../bindings/display/panel/panel-simple.yaml | 2 + > arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 30 +- > drivers/gpu/drm/Kconfig | 5 + > drivers/gpu/drm/Makefile | 2 + > drivers/gpu/drm/bridge/Kconfig | 1 + > drivers/gpu/drm/bridge/ti-sn65dsi86.c | 111 ++++-- > drivers/gpu/drm/drm_dp_aux_bus.c | 322 ++++++++++++++++++ > drivers/gpu/drm/panel/Kconfig | 1 + > drivers/gpu/drm/panel/panel-simple.c | 66 +++- > include/drm/drm_dp_aux_bus.h | 57 ++++ > 11 files changed, 563 insertions(+), 56 deletions(-) > create mode 100644 drivers/gpu/drm/drm_dp_aux_bus.c > create mode 100644 include/drm/drm_dp_aux_bus.h >
Hi, On Fri, May 21, 2021 at 4:07 PM Lyude Paul <lyude@redhat.com> wrote: > > For patches 5, and 6: > > Reviewed-by: Lyude Paul <lyude@redhat.com> > > This week got really busy so I wasn't able to look at the rest of them, but next > week is going to be a lot less busy so I should be able to look at them then Thanks for your review on the two patches and for letting me know your plans. I know that I still need to spin the bindings patches with Rob Herring's feedback, but I won't do that until I know you're done reviewing just to avoid spamming everyone an extra time. Assuming no emergency comes around and slams me, I should be able to react/respond fairly quickly this week M-Th, though I'm taking Friday off. BTW: if anyone reading this happens to have 10 minutes, I'd sorta like to get patch #1 in this series landed sooner rather than later and it's a dead-simple fix. If I see a review of that one, I'll apply it to drm-misc before sending out the next version of the series. ;-) -Doug
The primary goal of this series is to try to properly fix EDID reading for eDP panels using the ti-sn65dsi86 bridge. Previously we had a patch that added EDID reading but it turned out not to work at bootup. This caused some extra churn at bootup as we tried (and failed) to read the EDID several times and also ended up forcing us to use the hardcoded mode at boot. With this patch series I believe EDID reading is reliable at boot now and we never use the hardcoded mode. High level note: in this series the EDID reading is driven by the panel driver, not by the bridge chip driver. I believe this makes a reasonable amount of sense since the panel driver already _could_ drive reading the EDID if provided with the DDC bus and in future planned work we'll want to give the panel driver the DDC bus (to make decisions based on EDID) and the AUX bus (to control the backlight). There are also planned patches from Laurent to make ti-sn65dsi86 able to drive full DP monitors. In that case the bridge chip will still be in charge of reading the EDID, but it's not hard to make this dynamic. This series is the logical successor to the 3-part series containing the patch ("drm/bridge: ti-sn65dsi86: Properly get the EDID, but only if refclk") [1]. This patch was tested against drm-misc-next commit 60a6b73dd821 ("drm/ingenic: Fix pixclock rate for 24-bit serial panels") on a sc7180-trogdor-lazor device. At v7 now, this patch series grew a bit from v6 because it introduces the DP AUX bus. Between v2 and v3, high-level view of changes: - stop doing the EDID caching in the core. Between v3 and v4, high-level view of changes: - EDID reading is actually driven by the panel driver now. See above. - Lots of chicken-and-egg problems solved w/ sub-devices. Between v4 and v5, high-level view of changes. - Some of the early patches landed, so dropped from series. - New pm_runtime_disable() fix (fixed a patch that already landed). - Added Bjorn's tags to most patches - Fixed problems when building as a module. - Reordered debugfs patch and fixed error handling there. - Dropped last patch. I'm not convinced it's safe w/out more work. Between v5 and v6, high-level view of changes: - Added the patch ("drm/dp: Allow an early call to register DDC i2c bus") - Many patches had been landed, so only a few "controversial" ones left. Between v6 and v7, high-level view of changes: - New AUX DP bus! [1] https://lore.kernel.org/r/20210304155144.3.I60a7fb23ce4589006bc95c64ab8d15c74b876e68@changeid/ Changes in v7: - pm_runtime_dont_use_autosuspend() fix new for v7. - List hpd properties bindings patch new for v7. - ti-sn65dsi86: Add aux-bus child patch new for v7. - Patch introducing the DP AUX bus is new for v7. - Patch to allow panel-simple to be DP AUX EP new for v7. - Patch using the DP AUX for DDC new for v7. - Remove use of now-dropped drm_dp_aux_register_ddc() call. - Beefed up commit message in context of the DP AUX bus. - Set the proper sub-device "dev" pointer in the AUX structure. - Patch to support for DP AUX bus on ti-sn65dsi86 new for v7. - Adjusted commit message to talk about DP AUX bus. - Panel now under bridge chip instead of getting a link to ddc-i2c Changes in v6: - Use new drm_dp_aux_register_ddc() calls. Douglas Anderson (10): drm/panel: panel-simple: Add missing pm_runtime_dont_use_autosuspend() calls dt-bindings: display: simple: List hpd properties in panel-simple dt-bindings: drm/bridge: ti-sn65dsi86: Add aux-bus child drm: Introduce the DP AUX bus drm/panel: panel-simple: Allow panel-simple be a DP AUX endpoint device drm/panel: panel-simple: Stash DP AUX bus; allow using it for DDC drm/bridge: ti-sn65dsi86: Promote the AUX channel to its own sub-dev drm/bridge: ti-sn65dsi86: Add support for the DP AUX bus drm/bridge: ti-sn65dsi86: Don't read EDID blob over DDC arm64: dts: qcom: sc7180-trogdor: Move panel under the bridge chip .../bindings/display/bridge/ti,sn65dsi86.yaml | 22 +- .../bindings/display/panel/panel-simple.yaml | 2 + arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 30 +- drivers/gpu/drm/Kconfig | 5 + drivers/gpu/drm/Makefile | 2 + drivers/gpu/drm/bridge/Kconfig | 1 + drivers/gpu/drm/bridge/ti-sn65dsi86.c | 111 ++++-- drivers/gpu/drm/drm_dp_aux_bus.c | 322 ++++++++++++++++++ drivers/gpu/drm/panel/Kconfig | 1 + drivers/gpu/drm/panel/panel-simple.c | 66 +++- include/drm/drm_dp_aux_bus.h | 57 ++++ 11 files changed, 563 insertions(+), 56 deletions(-) create mode 100644 drivers/gpu/drm/drm_dp_aux_bus.c create mode 100644 include/drm/drm_dp_aux_bus.h