| Message ID | 20230216125257.112300-1-brgl@bgdev.pl (mailing list archive) |
|---|---|
| Headers | show |
| Series | arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs | expand |
On Thu, Feb 16, 2023 at 1:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote: > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > This enables the QUPv3 interfaces that are exposed on the sa8775p-ride > board: I2C, SPI and the Bluetooth and GNSS UART ports. > > v2 -> v3: > - fix the interrupt number for uart12 > - replace underscores with hyphens in DT node names (although make dtbs_check > does not raise warnings about this) > - rearrange the commits so that they're more fine-grained with separate > patches for adding nodes to dtsi and enabling them for the board > > v1 -> v2: > - uart17 is the Bluetooth port, not GNSS > - add uart12 for GNSS too in that case > > Bartosz Golaszewski (9): > arm64: dts: qcom: sa8775p: add the QUPv3 #2 node > arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2 > arm64: dts: qcom: sa8775p: add the i2c18 node > arm64: dts: qcom: sa8775p-ride: enable i2c18 > arm64: dts: qcom: sa8775p: add the spi16 node > arm64: dts: qcom: sa8775p-ride: enable the SPI node > arm64: dts: qcom: sa8775p: add high-speed UART nodes > arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port > arm64: dts: qcom: sa8775p-ride: enable the BT UART port > > arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 100 ++++++++++++++++++++++ > arch/arm64/boot/dts/qcom/sa8775p.dtsi | 86 +++++++++++++++++++ > 2 files changed, 186 insertions(+) > > -- > 2.37.2 > Konrad, Krzysztof et al, It's been over two weeks, could you please take a look and let me know if this is good to go? Thanks, Bartosz
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> This enables the QUPv3 interfaces that are exposed on the sa8775p-ride board: I2C, SPI and the Bluetooth and GNSS UART ports. v2 -> v3: - fix the interrupt number for uart12 - replace underscores with hyphens in DT node names (although make dtbs_check does not raise warnings about this) - rearrange the commits so that they're more fine-grained with separate patches for adding nodes to dtsi and enabling them for the board v1 -> v2: - uart17 is the Bluetooth port, not GNSS - add uart12 for GNSS too in that case Bartosz Golaszewski (9): arm64: dts: qcom: sa8775p: add the QUPv3 #2 node arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2 arm64: dts: qcom: sa8775p: add the i2c18 node arm64: dts: qcom: sa8775p-ride: enable i2c18 arm64: dts: qcom: sa8775p: add the spi16 node arm64: dts: qcom: sa8775p-ride: enable the SPI node arm64: dts: qcom: sa8775p: add high-speed UART nodes arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port arm64: dts: qcom: sa8775p-ride: enable the BT UART port arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 100 ++++++++++++++++++++++ arch/arm64/boot/dts/qcom/sa8775p.dtsi | 86 +++++++++++++++++++ 2 files changed, 186 insertions(+)