| Message ID | 20230309103752.173541-1-brgl@bgdev.pl (mailing list archive) |
|---|---|
| Headers | show |
| Series | arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs | expand |
On Thu, Mar 9, 2023 at 11:37 AM Bartosz Golaszewski <brgl@bgdev.pl> wrote: > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > This enables the QUPv3 interfaces that are exposed on the sa8775p-ride > board: I2C, SPI and the Bluetooth and GNSS UART ports. > > v4 -> v5: > - remove board-specific interrupt from UART17 in SoC dtsi > - rearrange node properties to have various *-cells properties come right > before status > - collect more tags > > v3 -> v4: > - use interconnect constants instead of magic numbers where applicable > - pad addresses in reg to 8 digits > - group pins under state nodes for UART > > v2 -> v3: > - fix the interrupt number for uart12 > - replace underscores with hyphens in DT node names (although make dtbs_check > does not raise warnings about this) > - rearrange the commits so that they're more fine-grained with separate > patches for adding nodes to dtsi and enabling them for the board > > v1 -> v2: > - uart17 is the Bluetooth port, not GNSS > - add uart12 for GNSS too in that case > > Bartosz Golaszewski (9): > arm64: dts: qcom: sa8775p: add the QUPv3 #2 node > arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2 > arm64: dts: qcom: sa8775p: add the i2c18 node > arm64: dts: qcom: sa8775p-ride: enable i2c18 > arm64: dts: qcom: sa8775p: add the spi16 node > arm64: dts: qcom: sa8775p-ride: enable the SPI node > arm64: dts: qcom: sa8775p: add high-speed UART nodes > arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port > arm64: dts: qcom: sa8775p-ride: enable the BT UART port > > arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 99 +++++++++++++++++++++++ > arch/arm64/boot/dts/qcom/sa8775p.dtsi | 86 ++++++++++++++++++++ > 2 files changed, 185 insertions(+) > > -- > 2.37.2 > Bjorn, I noticed you're picking up the reviewed patches. :) This series seems ready to go into your tree as well. Thanks in advance, Bartosz
On Thu, 9 Mar 2023 11:37:43 +0100, Bartosz Golaszewski wrote: > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > This enables the QUPv3 interfaces that are exposed on the sa8775p-ride > board: I2C, SPI and the Bluetooth and GNSS UART ports. > > v4 -> v5: > - remove board-specific interrupt from UART17 in SoC dtsi > - rearrange node properties to have various *-cells properties come right > before status > - collect more tags > > [...] Applied, thanks! [1/9] arm64: dts: qcom: sa8775p: add the QUPv3 #2 node commit: dc3ad22112de7fe76352ef2aa2943b62eb1836a3 [2/9] arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2 commit: 4926a8e93f321760fa265f91d78aa2a2163e222b [3/9] arm64: dts: qcom: sa8775p: add the i2c18 node commit: a23d122572a4ad1292e60d4a87e6f0238aaa0505 [4/9] arm64: dts: qcom: sa8775p-ride: enable i2c18 commit: 12f35f74ad6da53d94fcbc1bbb2adff60b31a71f [5/9] arm64: dts: qcom: sa8775p: add the spi16 node commit: cfd975f588400e0942d55dc4bb84c12c6f217fb4 [6/9] arm64: dts: qcom: sa8775p-ride: enable the SPI node commit: a3b31b0e0f76326bfa4bc81577f52738ad8e072b [7/9] arm64: dts: qcom: sa8775p: add high-speed UART nodes commit: 41ae5ca448c21a82a2f07e10954b043a0d45a811 [8/9] arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port commit: 4b6c4249069694a593f3b4c3d81c75a5053b7693 [9/9] arm64: dts: qcom: sa8775p-ride: enable the BT UART port commit: e1988af7a646aafe8075b179c00fd8053ced2add Best regards,
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> This enables the QUPv3 interfaces that are exposed on the sa8775p-ride board: I2C, SPI and the Bluetooth and GNSS UART ports. v4 -> v5: - remove board-specific interrupt from UART17 in SoC dtsi - rearrange node properties to have various *-cells properties come right before status - collect more tags v3 -> v4: - use interconnect constants instead of magic numbers where applicable - pad addresses in reg to 8 digits - group pins under state nodes for UART v2 -> v3: - fix the interrupt number for uart12 - replace underscores with hyphens in DT node names (although make dtbs_check does not raise warnings about this) - rearrange the commits so that they're more fine-grained with separate patches for adding nodes to dtsi and enabling them for the board v1 -> v2: - uart17 is the Bluetooth port, not GNSS - add uart12 for GNSS too in that case Bartosz Golaszewski (9): arm64: dts: qcom: sa8775p: add the QUPv3 #2 node arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2 arm64: dts: qcom: sa8775p: add the i2c18 node arm64: dts: qcom: sa8775p-ride: enable i2c18 arm64: dts: qcom: sa8775p: add the spi16 node arm64: dts: qcom: sa8775p-ride: enable the SPI node arm64: dts: qcom: sa8775p: add high-speed UART nodes arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port arm64: dts: qcom: sa8775p-ride: enable the BT UART port arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 99 +++++++++++++++++++++++ arch/arm64/boot/dts/qcom/sa8775p.dtsi | 86 ++++++++++++++++++++ 2 files changed, 185 insertions(+)