mbox series

[v2,0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS

Message ID 20240313123017.362570-1-sumit.garg@linaro.org (mailing list archive)
Headers show
Series arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS | expand

Message

Sumit Garg March 13, 2024, 12:30 p.m. UTC 
Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
Box Core board based on the Qualcomm APQ8016E SoC. For more information
refer to the product page [1].

One of the major difference from db410c is serial port where HMIBSC board
uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
configured via gpio99 and gpio100).

Support for Schneider Electric HMIBSC. Features:
- Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
- 1GiB RAM
- 8GiB eMMC, SD slot
- WiFi and Bluetooth
- 2x Host, 1x Device USB port
- HDMI
- Discrete TPM2 chip over SPI
- USB ethernet adaptors (soldered)

This series is a v2 since v1 of this DTS file has been reviewed on the
U-Boot mailing list [2].

Changes in v2:
- Fix DT schema warnings.
- Incorporate suggestions from Stephan.
- Document UART1 mode GPIOs based mux.

[1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@linaro.org/

Sumit Garg (3):
  dt-bindings: vendor-prefixes: Add Schneider Electric
  dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board
  arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/apq8016-schneider-hmibsc.dts     | 519 ++++++++++++++++++
 4 files changed, 523 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts

Comments

Krzysztof Kozlowski March 13, 2024, 12:57 p.m. UTC | #1 
On 13/03/2024 13:30, Sumit Garg wrote:
> Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> Box Core board based on the Qualcomm APQ8016E SoC. For more information
> refer to the product page [1].
> 
> One of the major difference from db410c is serial port where HMIBSC board
> uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
> configured via gpio99 and gpio100).
> 
> Support for Schneider Electric HMIBSC. Features:
> - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> - 1GiB RAM
> - 8GiB eMMC, SD slot
> - WiFi and Bluetooth
> - 2x Host, 1x Device USB port
> - HDMI
> - Discrete TPM2 chip over SPI
> - USB ethernet adaptors (soldered)
> 
> This series is a v2 since v1 of this DTS file has been reviewed on the
> U-Boot mailing list [2].
> 
> Changes in v2:
> - Fix DT schema warnings.

Quick look tells me this is not the case.

Best regards,
Krzysztof