| Message ID | 1409052645-14984-1-git-send-email-kiran.padwal@smartplayin.com (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
On Tue, Aug 26, 2014 at 05:00:45PM +0530, Kiran Padwal wrote: > This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. > It also adds necessary DT support for i2c eeprom which is present on > IFC6410. > > Tested on IFC6410 board. Looks fine > > Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> > --- > Changes since v2: > - Renamed pinmux i2c subnode "i2c1_pinmux" to "i2c1". > - Removed labes of node. > - Used canonical value as "okay" instead of "ok". > - Used macros. > > Changes since v1: > - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". > - Updated pinmux interrupt. > > arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 27 ++++++++++++++ > arch/arm/boot/dts/qcom-apq8064.dtsi | 53 ++++++++++++++++++++++++++++ > 2 files changed, 80 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > index 7c2441d..ef0857e 100644 > --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > @@ -5,6 +5,24 @@ > compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; > > soc { > + gsbi@12440000 { > + status = "okay"; > + qcom,mode = <GSBI_PROT_I2C>; > + > + i2c@12460000 { > + status = "okay"; > + clock-frequency = <200000>; > + pinctrl-0 = <&i2c1_pins>; > + pinctrl-names = "default"; > + > + eeprom: eeprom@52 { > + compatible = "atmel,24c128"; > + reg = <0x52>; > + pagesize = <32>; > + }; don't need read only here. the eeprom is not being used by anything.... thankfully. > + }; > + }; > + > gsbi@16600000 { > status = "ok"; > qcom,mode = <GSBI_PROT_I2C_UART>; > @@ -12,5 +30,14 @@ > status = "ok"; > }; > }; > + > + pinmux@800000 { > + i2c1_pins: i2c1 { > + mux { > + pins = "gpio20", "gpio21"; > + function = "gsbi1"; > + }; > + }; > + }; > }; > }; > diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi > index 92bf793..5dddbf3 100644 > --- a/arch/arm/boot/dts/qcom-apq8064.dtsi > +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi > @@ -89,6 +89,17 @@ > cpu-offset = <0x80000>; > }; > > + tlmm_pinmux: pinmux@800000 { > + compatible = "qcom,apq8064-pinctrl"; > + reg = <0x800000 0x4000>; > + > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > acc0: clock-controller@2088000 { > compatible = "qcom,kpss-acc-v1"; > reg = <0x02088000 0x1000>, <0x02008000 0x1000>; > @@ -133,6 +144,48 @@ > regulator; > }; > > + gsbi1: gsbi@12440000 { > + status = "disabled"; > + compatible = "qcom,gsbi-v1.0.0"; > + reg = <0x12440000 0x100>; > + clocks = <&gcc GSBI1_H_CLK>; > + clock-names = "iface"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + i2c1: i2c@12460000 { > + compatible = "qcom,i2c-qup-v1.1.1"; > + reg = <0x12460000 0x1000>; > + interrupts = <0 194 IRQ_TYPE_NONE>; > + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; > + clock-names = "core", "iface"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > + gsbi2: gsbi@12480000 { > + status = "disabled"; > + compatible = "qcom,gsbi-v1.0.0"; > + reg = <0x12480000 0x100>; > + clocks = <&gcc GSBI2_H_CLK>; > + clock-names = "iface"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + i2c2: i2c@124a0000 { > + compatible = "qcom,i2c-qup-v1.1.1"; > + reg = <0x124a0000 0x1000>; > + interrupts = <0 196 IRQ_TYPE_NONE>; > + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; > + clock-names = "core", "iface"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > gsbi7: gsbi@16600000 { > status = "disabled"; > compatible = "qcom,gsbi-v1.0.0"; > -- > 1.7.9.5 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html
On Monday, September 15, 2014 10:39pm, "Andy Gross" <agross@codeaurora.org> said: > On Tue, Aug 26, 2014 at 05:00:45PM +0530, Kiran Padwal wrote: >> This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. >> It also adds necessary DT support for i2c eeprom which is present on >> IFC6410. >> >> Tested on IFC6410 board. > > Looks fine Thanks for review. > >> >> Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> >> --- >> Changes since v2: >> - Renamed pinmux i2c subnode "i2c1_pinmux" to "i2c1". >> - Removed labes of node. >> - Used canonical value as "okay" instead of "ok". >> - Used macros. >> >> Changes since v1: >> - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". >> - Updated pinmux interrupt. >> >> arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 27 ++++++++++++++ >> arch/arm/boot/dts/qcom-apq8064.dtsi | 53 ++++++++++++++++++++++++++++ >> 2 files changed, 80 insertions(+) >> >> diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> index 7c2441d..ef0857e 100644 >> --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> @@ -5,6 +5,24 @@ >> compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; >> >> soc { >> + gsbi@12440000 { >> + status = "okay"; >> + qcom,mode = <GSBI_PROT_I2C>; >> + >> + i2c@12460000 { >> + status = "okay"; >> + clock-frequency = <200000>; >> + pinctrl-0 = <&i2c1_pins>; >> + pinctrl-names = "default"; >> + >> + eeprom: eeprom@52 { >> + compatible = "atmel,24c128"; >> + reg = <0x52>; >> + pagesize = <32>; >> + }; > > don't need read only here. the eeprom is not being used by anything.... > thankfully. > >> + }; >> + }; >> + >> gsbi@16600000 { >> status = "ok"; >> qcom,mode = <GSBI_PROT_I2C_UART>; >> @@ -12,5 +30,14 @@ >> status = "ok"; >> }; >> }; >> + >> + pinmux@800000 { >> + i2c1_pins: i2c1 { >> + mux { >> + pins = "gpio20", "gpio21"; >> + function = "gsbi1"; >> + }; >> + }; >> + }; >> }; >> }; >> diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi >> b/arch/arm/boot/dts/qcom-apq8064.dtsi >> index 92bf793..5dddbf3 100644 >> --- a/arch/arm/boot/dts/qcom-apq8064.dtsi >> +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi >> @@ -89,6 +89,17 @@ >> cpu-offset = <0x80000>; >> }; >> >> + tlmm_pinmux: pinmux@800000 { >> + compatible = "qcom,apq8064-pinctrl"; >> + reg = <0x800000 0x4000>; >> + >> + gpio-controller; >> + #gpio-cells = <2>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>; >> + }; >> + >> acc0: clock-controller@2088000 { >> compatible = "qcom,kpss-acc-v1"; >> reg = <0x02088000 0x1000>, <0x02008000 0x1000>; >> @@ -133,6 +144,48 @@ >> regulator; >> }; >> >> + gsbi1: gsbi@12440000 { >> + status = "disabled"; >> + compatible = "qcom,gsbi-v1.0.0"; >> + reg = <0x12440000 0x100>; >> + clocks = <&gcc GSBI1_H_CLK>; >> + clock-names = "iface"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + >> + i2c1: i2c@12460000 { >> + compatible = "qcom,i2c-qup-v1.1.1"; >> + reg = <0x12460000 0x1000>; >> + interrupts = <0 194 IRQ_TYPE_NONE>; >> + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; >> + clock-names = "core", "iface"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> + gsbi2: gsbi@12480000 { >> + status = "disabled"; >> + compatible = "qcom,gsbi-v1.0.0"; >> + reg = <0x12480000 0x100>; >> + clocks = <&gcc GSBI2_H_CLK>; >> + clock-names = "iface"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + >> + i2c2: i2c@124a0000 { >> + compatible = "qcom,i2c-qup-v1.1.1"; >> + reg = <0x124a0000 0x1000>; >> + interrupts = <0 196 IRQ_TYPE_NONE>; >> + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; >> + clock-names = "core", "iface"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> gsbi7: gsbi@16600000 { >> status = "disabled"; >> compatible = "qcom,gsbi-v1.0.0"; >> -- >> 1.7.9.5 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in >> the body of a message to majordomo@vger.kernel.org >> More majordomo info at http://vger.kernel.org/majordomo-info.html > > -- > sent by an employee of the Qualcomm Innovation Center, Inc. > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > hosted by The Linux Foundation > -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Sep 16, 2014, at 5:36 AM, kiran.padwal@smartplayin.com wrote: > > > On Monday, September 15, 2014 10:39pm, "Andy Gross" <agross@codeaurora.org> said: > >> On Tue, Aug 26, 2014 at 05:00:45PM +0530, Kiran Padwal wrote: >>> This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. >>> It also adds necessary DT support for i2c eeprom which is present on >>> IFC6410. >>> >>> Tested on IFC6410 board. >> >> Looks fine > > Thanks for review. Can you rebase this on: git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom.git tags/qcom-dt-for-3.18 - k
On Tuesday, September 16, 2014 3:00pm, "Kumar Gala" <galak@codeaurora.org> said: > > On Sep 16, 2014, at 5:36 AM, kiran.padwal@smartplayin.com wrote: > >> >> >> On Monday, September 15, 2014 10:39pm, "Andy Gross" <agross@codeaurora.org> >> said: >> >>> On Tue, Aug 26, 2014 at 05:00:45PM +0530, Kiran Padwal wrote: >>>> This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. >>>> It also adds necessary DT support for i2c eeprom which is present on >>>> IFC6410. >>>> >>>> Tested on IFC6410 board. >>> >>> Looks fine >> >> Thanks for review. > > Can you rebase this on: > > git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom.git > tags/qcom-dt-for-3.18 Sure, I will resend this patch gain. > > - k > > -- > Employee of Qualcomm Innovation Center, Inc. > Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The > Linux Foundation > > -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index 7c2441d..ef0857e 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -5,6 +5,24 @@ compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; soc { + gsbi@12440000 { + status = "okay"; + qcom,mode = <GSBI_PROT_I2C>; + + i2c@12460000 { + status = "okay"; + clock-frequency = <200000>; + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + eeprom: eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + pagesize = <32>; + }; + }; + }; + gsbi@16600000 { status = "ok"; qcom,mode = <GSBI_PROT_I2C_UART>; @@ -12,5 +30,14 @@ status = "ok"; }; }; + + pinmux@800000 { + i2c1_pins: i2c1 { + mux { + pins = "gpio20", "gpio21"; + function = "gsbi1"; + }; + }; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index 92bf793..5dddbf3 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -89,6 +89,17 @@ cpu-offset = <0x80000>; }; + tlmm_pinmux: pinmux@800000 { + compatible = "qcom,apq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>; + }; + acc0: clock-controller@2088000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; @@ -133,6 +144,48 @@ regulator; }; + gsbi1: gsbi@12440000 { + status = "disabled"; + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12440000 0x100>; + clocks = <&gcc GSBI1_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + i2c1: i2c@12460000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x12460000 0x1000>; + interrupts = <0 194 IRQ_TYPE_NONE>; + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; + clock-names = "core", "iface"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + gsbi2: gsbi@12480000 { + status = "disabled"; + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12480000 0x100>; + clocks = <&gcc GSBI2_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + i2c2: i2c@124a0000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x124a0000 0x1000>; + interrupts = <0 196 IRQ_TYPE_NONE>; + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; + clock-names = "core", "iface"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + gsbi7: gsbi@16600000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0";
This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. It also adds necessary DT support for i2c eeprom which is present on IFC6410. Tested on IFC6410 board. Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> --- Changes since v2: - Renamed pinmux i2c subnode "i2c1_pinmux" to "i2c1". - Removed labes of node. - Used canonical value as "okay" instead of "ok". - Used macros. Changes since v1: - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". - Updated pinmux interrupt. arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 27 ++++++++++++++ arch/arm/boot/dts/qcom-apq8064.dtsi | 53 ++++++++++++++++++++++++++++ 2 files changed, 80 insertions(+)