diff mbox

[V4,4/7] i2c: qup: Transfer each i2c_msg in i2c_msgs without a stop bit

Message ID 1436412350-19519-5-git-send-email-sricharan@codeaurora.org (mailing list archive)
State New, archived
Delegated to: Andy Gross
Headers show

Commit Message

Sricharan Ramabadhran July 9, 2015, 3:25 a.m. UTC
The definition of i2c_msg says that

"If this is the last message in a group, it is followed by a STOP.
Otherwise it is followed by the next @i2c_msg transaction segment,
beginning with a (repeated) START"

So the expectation is that there is no 'STOP' bit inbetween individual
i2c_msg segments with repeated 'START'. The QUP i2c hardware has no way
to inform that there should not be a 'STOP' at the end of transaction.
The only way to implement this is to coalesce all the i2c_msg in i2c_msgs
in to one transaction and transfer them. Adding the support for the same.

This is required for some clients like touchscreen which keeps
incrementing counts across individual transfers and 'STOP' bit inbetween
resets the counter, which is not required.

This patch adds the support in non-dma mode.

Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
 drivers/i2c/busses/i2c-qup.c | 40 ++++++++++++++++++++++++++++++----------
 1 file changed, 30 insertions(+), 10 deletions(-)

Comments

Ivan T. Ivanov July 20, 2015, 11:22 a.m. UTC | #1
Hi, 

On Thu, 2015-07-09 at 08:55 +0530, Sricharan R wrote:

<snip>

>  #define ONE_BYTE                       0x1
> +#define QUP_I2C_MX_CONFIG_DURING_RUN   BIT(31)
> 
>  struct qup_i2c_block {
>         int     count;
> @@ -121,6 +122,7 @@ struct qup_i2c_block {
>         int     rx_tag_len;
>         int     data_len;
>         u8      tags[6];
> +       int     config_run;

This is not directly related to "block" control logic, right?
Could it made part of qup_i2c_dev structure?

>  };
> 
>  struct qup_i2c_dev {
> @@ -152,6 +154,10 @@ struct qup_i2c_dev {
> 
>         int (*qup_i2c_write_one)(struct qup_i2c_dev *qup,
>                                         struct i2c_msg *msg);
> +       /* Current i2c_msg in i2c_msgs */
> +       int     cmsg;
> +       /* total num of i2c_msgs */
> +       int     num;

I think it will be simpler with just "bool is_last" evaluated in main xfer loop.

<snip>

> 
> @@ -374,6 +383,9 @@ static void qup_i2c_get_blk_data(struct qup_i2c_dev *qup,
>         /* There are 2 tag bytes that are read in to fifo for every block */
>         if (msg->flags & I2C_M_RD)
>                 qup->blk.rx_tag_len = qup->blk.count * 2;
> +
> +       if (qup->cmsg)
> +               qup->blk.config_run = QUP_I2C_MX_CONFIG_DURING_RUN;

This could be moved to qup_i2c_xfer_v2() to avoid repeatedly setting it. 

>  }

Regards,
Ivan
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Sricharan Ramabadhran July 21, 2015, 8:09 a.m. UTC | #2
Hi Ivan,

> -----Original Message-----
> From: Ivan T. Ivanov [mailto:iivanov@mm-sol.com]
> Sent: Monday, July 20, 2015 4:53 PM
> To: Sricharan R
> Cc: devicetree@vger.kernel.org; linux-arm-msm@vger.kernel.org;
> galak@codeaurora.org; linux-kernel@vger.kernel.org; linux-
> i2c@vger.kernel.org; agross@codeaurora.org; dmaengine@vger.kernel.org;
> linux-arm-kernel@lists.infradead.org
> Subject: Re: [PATCH V4 4/7] i2c: qup: Transfer each i2c_msg in i2c_msgs
> without a stop bit
> 
> 
> Hi,
> 
> On Thu, 2015-07-09 at 08:55 +0530, Sricharan R wrote:
> 
> <snip>
> 
> >  #define ONE_BYTE                       0x1
> > +#define QUP_I2C_MX_CONFIG_DURING_RUN   BIT(31)
> >
> >  struct qup_i2c_block {
> >         int     count;
> > @@ -121,6 +122,7 @@ struct qup_i2c_block {
> >         int     rx_tag_len;
> >         int     data_len;
> >         u8      tags[6];
> > +       int     config_run;
> 
> This is not directly related to "block" control logic, right?
> Could it made part of qup_i2c_dev structure?
> 
   Yes, can move it there.

> >  };
> >
> >  struct qup_i2c_dev {
> > @@ -152,6 +154,10 @@ struct qup_i2c_dev {
> >
> >         int (*qup_i2c_write_one)(struct qup_i2c_dev *qup,
> >                                         struct i2c_msg *msg);
> > +       /* Current i2c_msg in i2c_msgs */
> > +       int     cmsg;
> > +       /* total num of i2c_msgs */
> > +       int     num;
> 
> I think it will be simpler with just "bool is_last" evaluated in main xfer loop.
  
   Hmm ok. Will change it that way. Set it one place and use it other places.
> 
> <snip>
> 
> >
> > @@ -374,6 +383,9 @@ static void qup_i2c_get_blk_data(struct
> qup_i2c_dev *qup,
> >         /* There are 2 tag bytes that are read in to fifo for every block */
> >         if (msg->flags & I2C_M_RD)
> >                 qup->blk.rx_tag_len = qup->blk.count * 2;
> > +
> > +       if (qup->cmsg)
> > +               qup->blk.config_run = QUP_I2C_MX_CONFIG_DURING_RUN;
> 
> This could be moved to qup_i2c_xfer_v2() to avoid repeatedly setting it.
     Ok, correct.

Regards,
 Sricharan

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c
index a4e20d9..c0757d9 100644
--- a/drivers/i2c/busses/i2c-qup.c
+++ b/drivers/i2c/busses/i2c-qup.c
@@ -113,6 +113,7 @@ 
 #define SET_BIT				0x1
 #define RESET_BIT			0x0
 #define ONE_BYTE			0x1
+#define QUP_I2C_MX_CONFIG_DURING_RUN   BIT(31)
 
 struct qup_i2c_block {
 	int	count;
@@ -121,6 +122,7 @@  struct qup_i2c_block {
 	int	rx_tag_len;
 	int	data_len;
 	u8	tags[6];
+	int     config_run;
 };
 
 struct qup_i2c_dev {
@@ -152,6 +154,10 @@  struct qup_i2c_dev {
 
 	int (*qup_i2c_write_one)(struct qup_i2c_dev *qup,
 				 struct i2c_msg *msg);
+	/* Current i2c_msg in i2c_msgs */
+	int			cmsg;
+	/* total num of i2c_msgs */
+	int			num;
 
 	int (*qup_i2c_read_one)(struct qup_i2c_dev *qup,
 				struct i2c_msg *msg);
@@ -278,7 +284,8 @@  static int qup_i2c_wait_ready(struct qup_i2c_dev *qup, int op, bool val,
 		status = readl(qup->base + QUP_I2C_STATUS);
 
 		if (((opflags & op) >> shift) == val) {
-			if (op == QUP_OUT_NOT_EMPTY) {
+			if ((op == QUP_OUT_NOT_EMPTY) &&
+			    (qup->cmsg == (qup->num - 1))) {
 				if (!(status & I2C_STATUS_BUS_ACTIVE))
 					return 0;
 			} else {
@@ -301,12 +308,14 @@  static void qup_i2c_set_write_mode(struct qup_i2c_dev *qup, struct i2c_msg *msg)
 	if (total < qup->out_fifo_sz) {
 		/* FIFO mode */
 		writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE);
-		writel(total, qup->base + QUP_MX_WRITE_CNT);
+		writel(total | qup->blk.config_run,
+		       qup->base + QUP_MX_WRITE_CNT);
 	} else {
 		/* BLOCK mode (transfer data on chunks) */
 		writel(QUP_OUTPUT_BLK_MODE | QUP_REPACK_EN,
 		       qup->base + QUP_IO_MODE);
-		writel(total, qup->base + QUP_MX_OUTPUT_CNT);
+		writel(total | qup->blk.config_run,
+		       qup->base + QUP_MX_OUTPUT_CNT);
 	}
 }
 
@@ -374,6 +383,9 @@  static void qup_i2c_get_blk_data(struct qup_i2c_dev *qup,
 	/* There are 2 tag bytes that are read in to fifo for every block */
 	if (msg->flags & I2C_M_RD)
 		qup->blk.rx_tag_len = qup->blk.count * 2;
+
+	if (qup->cmsg)
+		qup->blk.config_run = QUP_I2C_MX_CONFIG_DURING_RUN;
 }
 
 static int qup_i2c_send_data(struct qup_i2c_dev *qup, int tlen, u8 *tbuf,
@@ -440,7 +452,8 @@  static int qup_i2c_get_tags(u8 *tags, struct qup_i2c_dev *qup,
 	}
 
 	/* Send _STOP commands for the last block */
-	if (qup->blk.pos == (qup->blk.count - 1)) {
+	if (qup->blk.pos == (qup->blk.count - 1)
+	    && (qup->cmsg == (qup->num - 1))) {
 		if (msg->flags & I2C_M_RD)
 			tags[len++] = QUP_TAG_V2_DATARD_STOP;
 		else
@@ -571,7 +584,6 @@  static int qup_i2c_write(struct qup_i2c_dev *qup, struct i2c_msg *msg)
 		goto err;
 
 	ret = qup_i2c_wait_ready(qup, QUP_OUT_NOT_EMPTY, RESET_BIT, ONE_BYTE);
-
 err:
 	disable_irq(qup->irq);
 	qup->msg = NULL;
@@ -584,18 +596,19 @@  static void qup_i2c_set_read_mode(struct qup_i2c_dev *qup, int len)
 	int tx_len = qup->blk.tx_tag_len;
 
 	len += qup->blk.rx_tag_len;
+	tx_len |= qup->blk.config_run;
 
 	if (len < qup->in_fifo_sz) {
 		/* FIFO mode */
 		writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE);
-		writel(len, qup->base + QUP_MX_READ_CNT);
 		writel(tx_len, qup->base + QUP_MX_WRITE_CNT);
+		writel(len | qup->blk.config_run, qup->base + QUP_MX_READ_CNT);
 	} else {
 		/* BLOCK mode (transfer data on chunks) */
 		writel(QUP_INPUT_BLK_MODE | QUP_REPACK_EN,
 		       qup->base + QUP_IO_MODE);
-		writel(len, qup->base + QUP_MX_INPUT_CNT);
 		writel(tx_len, qup->base + QUP_MX_OUTPUT_CNT);
+		writel(len | qup->blk.config_run, qup->base + QUP_MX_INPUT_CNT);
 	}
 }
 
@@ -770,6 +783,8 @@  static int qup_i2c_xfer(struct i2c_adapter *adap,
 	struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
 	int ret, idx;
 
+	qup->num = 1;
+
 	ret = pm_runtime_get_sync(qup->dev);
 	if (ret < 0)
 		goto out;
@@ -823,6 +838,9 @@  static int qup_i2c_xfer_v2(struct i2c_adapter *adap,
 	struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
 	int ret, idx;
 
+	qup->num = num;
+	qup->cmsg = 0;
+
 	ret = pm_runtime_get_sync(qup->dev);
 	if (ret < 0)
 		goto out;
@@ -854,13 +872,15 @@  static int qup_i2c_xfer_v2(struct i2c_adapter *adap,
 		else
 			ret = qup_i2c_write(qup, &msgs[idx]);
 
-		if (!ret)
-			ret = qup_i2c_change_state(qup, QUP_RESET_STATE);
-
 		if (ret)
 			break;
+
+		qup->cmsg++;
 	}
 
+	if (!ret)
+		ret = qup_i2c_change_state(qup, QUP_RESET_STATE);
+
 	if (ret == 0)
 		ret = num;
 out: