new file mode 100644
@@ -0,0 +1,42 @@
+Qualcomm SLIMBUS controller
+"qcom,slim-msm": This controller is used if applications processor
+ driver is controlling slimbus master component. This driver is
+ responsible for communicating with slave HW directly using
+ messaging interface, and doing data channel management.
+
+Required properties:
+
+ - reg : Offset and length of the register region(s) for the device
+ - reg-names : Register region name(s) referenced in reg above
+ Required register resource entries are:
+ "slimbus_physical": Physical adderss of controller register blocks
+ "slimbus_bam_physical": Physical address of Bus Access Module (BAM)
+ for this controller
+ - compatible : should be "qcom,slim-msm" if this is master component driver
+ - interrupts : Interrupt numbers used by this controller
+ - interrupt-names : Required interrupt resource entries are:
+ "slimbus_irq" : Interrupt for SLIMBUS core
+ - clocks : Interface and core clocks used by this slimbus controller
+ - clock-names : Required clock-name entries are:
+ "iface_clk" : Interface clock for this controller
+ "core_clk" : Interrupt for controller core's BAM
+
+Optional property:
+ - reg entry for slew rate : If slew rate control register is provided, this
+ entry should be used.
+ - reg-name for slew rate: "slimbus_slew_reg"
+
+Example:
+ slim@28080000 {
+ compatible = "qcom,slim-msm";
+ reg = <0x28080000 0x2000>,
+ reg-names = "slimbus_physical";
+ interrupts = <0 33 0>;
+ interrupt-names = "slimbus_irq";
+ clocks = <&lcc SLIMBUS_SRC>, <&lcc AUDIO_SLIMBUS_CLK>;
+ clock-names = "iface_clk", "core_clk";
+
+ slim_codec_slave {
+ enumeration-addr = [00 01 60 00 17 02];
+ };
+ };
@@ -9,3 +9,13 @@ menuconfig SLIMBUS
If unsure, choose N.
+if SLIMBUS
+config SLIM_QCOM_CTRL
+ tristate "Qualcomm Slimbus Manager Component"
+ depends on SLIMBUS
+ default n
+ help
+ Select driver if Qualcomm's Slimbus Manager Component is
+ programmed using Linux kernel.
+
+endif
@@ -2,3 +2,4 @@
# Makefile for kernel slimbus framework.
#
obj-$(CONFIG_SLIMBUS) += slim-core.o slim-messaging.o
+obj-$(CONFIG_SLIM_QCOM_CTRL) += slim-qcom-ctrl.o
new file mode 100644
@@ -0,0 +1,587 @@
+/* Copyright (c) 2011-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/slimbus.h>
+#include "slim-qcom.h"
+
+#define MSM_SLIM_NAME "msm_slim_ctrl"
+
+/* Manager registers */
+#define MGR_CFG 0x200
+#define MGR_STATUS 0x204
+#define MGR_INT_EN 0x210
+#define MGR_INT_STAT 0x214
+#define MGR_INT_CLR 0x218
+#define MGR_TX_MSG 0x230
+#define MGR_RX_MSG 0x270
+#define MGR_IE_STAT 0x2F0
+#define MGR_VE_STAT 0x300
+#define MGR_CFG_ENABLE 1
+
+/* Framer registers */
+#define FRM_CFG 0x400
+#define FRM_STAT 0x404
+#define FRM_INT_EN 0x410
+#define FRM_INT_STAT 0x414
+#define FRM_INT_CLR 0x418
+#define FRM_WAKEUP 0x41C
+#define FRM_CLKCTL_DONE 0x420
+#define FRM_IE_STAT 0x430
+#define FRM_VE_STAT 0x440
+
+/* Interface registers */
+#define INTF_CFG 0x600
+#define INTF_STAT 0x604
+#define INTF_INT_EN 0x610
+#define INTF_INT_STAT 0x614
+#define INTF_INT_CLR 0x618
+#define INTF_IE_STAT 0x630
+#define INTF_VE_STAT 0x640
+
+/* Interrupt status bits */
+#define MGR_INT_TX_NACKED_2 BIT(25)
+#define MGR_INT_MSG_BUF_CONTE BIT(26)
+#define MGR_INT_RX_MSG_RCVD BIT(30)
+#define MGR_INT_TX_MSG_SENT BIT(31)
+
+/* Framer config register settings */
+#define FRM_ACTIVE 1
+#define CLK_GEAR 7
+#define ROOT_FREQ 11
+#define REF_CLK_GEAR 15
+#define INTR_WAKE 19
+
+static int msm_slim_queue_tx(struct msm_slim_ctrl *dev, u32 *buf, u8 len,
+ u32 tx_reg)
+{
+ int i;
+
+ for (i = 0; i < (len + 3) >> 2; i++) {
+ dev_dbg(dev->dev, "AHB TX data:0x%x\n", buf[i]);
+ writel_relaxed(buf[i], dev->base + tx_reg + (i * 4));
+ }
+ /* Guarantee that message is sent before returning */
+ mb();
+ return 0;
+}
+
+static irqreturn_t msm_slim_interrupt(int irq, void *d)
+{
+ struct msm_slim_ctrl *dev = d;
+ u32 stat = readl_relaxed(dev->base + MGR_INT_STAT);
+ int err = 0;
+
+ if (stat & MGR_INT_TX_MSG_SENT || stat & MGR_INT_TX_NACKED_2) {
+ if (stat & MGR_INT_TX_MSG_SENT)
+ writel_relaxed(MGR_INT_TX_MSG_SENT,
+ dev->base + MGR_INT_CLR);
+ if (stat & MGR_INT_TX_NACKED_2) {
+ u32 mgr_stat = readl_relaxed(dev->base + MGR_STATUS);
+ u32 mgr_ie_stat = readl_relaxed(dev->base +
+ MGR_IE_STAT);
+ u32 frm_stat = readl_relaxed(dev->base + FRM_STAT);
+ u32 frm_cfg = readl_relaxed(dev->base + FRM_CFG);
+ u32 frm_intr_stat = readl_relaxed(dev->base +
+ FRM_INT_STAT);
+ u32 frm_ie_stat = readl_relaxed(dev->base +
+ FRM_IE_STAT);
+ u32 intf_stat = readl_relaxed(dev->base + INTF_STAT);
+ u32 intf_intr_stat = readl_relaxed(dev->base +
+ INTF_INT_STAT);
+ u32 intf_ie_stat = readl_relaxed(dev->base +
+ INTF_IE_STAT);
+
+ writel_relaxed(MGR_INT_TX_NACKED_2, dev->base +
+ MGR_INT_CLR);
+ dev_err(dev->dev, "TX Nack MGR:int:0x%x, stat:0x%x\n",
+ stat, mgr_stat);
+ dev_err(dev->dev, "TX Nack MGR:ie:0x%x\n", mgr_ie_stat);
+ dev_err(dev->dev, "TX Nack FRM:int:0x%x, stat:0x%x\n",
+ frm_intr_stat, frm_stat);
+ dev_err(dev->dev, "TX Nack FRM:cfg:0x%x, ie:0x%x\n",
+ frm_cfg, frm_ie_stat);
+ dev_err(dev->dev, "TX Nack INTF:intr:0x%x, stat:0x%x\n",
+ intf_intr_stat, intf_stat);
+ dev_err(dev->dev, "TX Nack INTF:ie:0x%x\n",
+ intf_ie_stat);
+ err = -ENOTCONN;
+ }
+ /**
+ * Guarantee that interrupt clear bit write goes through before
+ * signalling completion/exiting ISR
+ */
+ mb();
+ slim_return_tx(&dev->ctrl, err);
+ }
+ if (stat & MGR_INT_RX_MSG_RCVD) {
+ u8 mc, mt;
+ u8 len, i;
+ u32 *rx_buf, pkt[10];
+ bool q_rx = false;
+
+ pkt[0] = readl_relaxed(dev->base + MGR_RX_MSG);
+ mt = (pkt[0] >> 5) & 0x7;
+ mc = (pkt[0] >> 8) & 0xff;
+ len = pkt[0] & 0x1F;
+ dev_dbg(dev->dev, "RX-IRQ: MC: %x, MT: %x\n", mc, mt);
+
+ /**
+ * this message cannot be handled by ISR, so
+ * let work-queue handle it
+ */
+ if (mt == SLIM_MSG_MT_CORE &&
+ mc == SLIM_MSG_MC_REPORT_PRESENT)
+ rx_buf = (u32 *)slim_get_rx(&dev->ctrl);
+ else
+ rx_buf = pkt;
+
+ if (rx_buf == NULL) {
+ dev_err(dev->dev, "dropping RX:0x%x due to RX full\n",
+ pkt[0]);
+ goto rx_ret_irq;
+ }
+
+ rx_buf[0] = pkt[0];
+ for (i = 1; i < ((len + 3) >> 2); i++) {
+ rx_buf[i] = readl_relaxed(dev->base + MGR_RX_MSG +
+ (4 * i));
+ dev_dbg(dev->dev, "reading data: %x\n", rx_buf[i]);
+ }
+
+ switch (mc) {
+ u8 *buf, la;
+ u16 ele;
+
+ case SLIM_MSG_MC_REPORT_PRESENT:
+ q_rx = true;
+ break;
+ case SLIM_MSG_MC_REPLY_INFORMATION:
+ case SLIM_MSG_MC_REPLY_VALUE:
+ slim_msg_response(&dev->ctrl, (u8 *)(rx_buf + 1),
+ (u8)(*rx_buf >> 24), (len - 4));
+ break;
+ case SLIM_MSG_MC_REPORT_INFORMATION:
+ buf = (u8 *)rx_buf;
+ la = buf[2];
+ ele = (u16)buf[4] << 4;
+
+ ele |= ((buf[3] & 0xf0) >> 4);
+ /**
+ * report information is most likely loss of
+ * sync or collision detected in data slots
+ */
+ dev_err(dev->dev, "LA:%d report inf ele:0x%x\n",
+ la, ele);
+ for (i = 0; i < len - 5; i++)
+ dev_err(dev->dev, "bit-mask:%x\n",
+ buf[i+5]);
+ break;
+ default:
+ dev_err(dev->dev, "unsupported MC,%x MT:%x\n",
+ mc, mt);
+ break;
+ }
+rx_ret_irq:
+ writel_relaxed(MGR_INT_RX_MSG_RCVD, dev->base +
+ MGR_INT_CLR);
+ /**
+ * Guarantee that CLR bit write goes through
+ * before exiting
+ */
+ mb();
+ if (q_rx)
+ queue_work(dev->rxwq, &dev->wd);
+ }
+ /**
+ * All interrupts are handled: complex RX messages requiring more work
+ * are queued to work-queue, others are handled above
+ */
+ return IRQ_HANDLED;
+}
+
+/**
+ * Qualcomm slimbus controller may experience interference on the lines
+ * causing some early messages (e.g. logical-address assignment) to be
+ * NACKed. Retry after sometime (typically 1 superframe)
+ */
+static void msm_slim_wait_retry(struct msm_slim_ctrl *dev)
+{
+ int msec_per_frm = 0;
+ int sfr_per_sec;
+
+ /* Wait for 1 superframe, or default time and then retry */
+ sfr_per_sec = dev->framer.superfreq /
+ (1 << (SLIM_MAX_CLK_GEAR - dev->ctrl.clkgear));
+ if (sfr_per_sec)
+ msec_per_frm = MSEC_PER_SEC / sfr_per_sec;
+ if (msec_per_frm < DEF_RETRY_MS)
+ msec_per_frm = DEF_RETRY_MS;
+ msleep(msec_per_frm);
+}
+
+static int msm_xfer_msg(struct slim_controller *ctrl, struct slim_msg_txn *txn,
+ void *pbuf)
+{
+ struct msm_slim_ctrl *dev = slim_get_ctrldata(ctrl);
+ DECLARE_COMPLETION_ONSTACK(done);
+ u32 *head = (u32 *)pbuf;
+ u8 *puc = (u8 *)pbuf;
+ u8 la = txn->la;
+
+ /* HW expects length field to be excluded */
+ txn->rl--;
+
+ if (txn->dt == SLIM_MSG_DEST_LOGICALADDR)
+ *head = SLIM_MSG_ASM_FIRST_WORD(txn->rl, txn->mt, txn->mc, 0,
+ la);
+ else
+ *head = SLIM_MSG_ASM_FIRST_WORD(txn->rl, txn->mt, txn->mc, 1,
+ la);
+
+ if (txn->dt == SLIM_MSG_DEST_LOGICALADDR)
+ puc += 3;
+ else
+ puc += 2;
+ if (txn->mt == SLIM_MSG_MT_CORE && slim_tid_txn(txn->mt, txn->mc))
+ *(puc++) = txn->tid;
+ if ((txn->mt == SLIM_MSG_MT_CORE) &&
+ ((txn->mc >= SLIM_MSG_MC_REQUEST_INFORMATION &&
+ txn->mc <= SLIM_MSG_MC_REPORT_INFORMATION) ||
+ (txn->mc >= SLIM_MSG_MC_REQUEST_VALUE &&
+ txn->mc <= SLIM_MSG_MC_CHANGE_VALUE))) {
+ *(puc++) = (txn->ec & 0xFF);
+ *(puc++) = (txn->ec >> 8) & 0xFF;
+ }
+ if (txn->msg && txn->msg->wbuf)
+ memcpy(puc, txn->msg->wbuf, txn->msg->num_bytes);
+
+ return msm_slim_queue_tx(dev, head, txn->rl, MGR_TX_MSG);
+}
+
+static int msm_set_laddr(struct slim_controller *ctrl,
+ struct slim_eaddr *ead, u8 laddr)
+{
+ struct msm_slim_ctrl *dev = slim_get_ctrldata(ctrl);
+ u8 buf[7];
+ int ret, retries = 0;
+ struct slim_val_inf msg = {0};
+
+ DEFINE_SLIM_EDEST_TXN(txn, SLIM_MSG_MC_ASSIGN_LOGICAL_ADDRESS,
+ 10, laddr, &msg);
+
+ /* Enumeration address */
+ buf[0] = (u8)(ead->manf_id >> 8);
+ buf[1] = (u8)(ead->manf_id & 0xFF);
+ buf[2] = (u8) (ead->prod_code >> 8);
+ buf[3] = (u8) (ead->prod_code & 0xFF);
+ buf[4] = ead->dev_index;
+ buf[5] = ead->instance;
+ /* Logical address for this EA */
+ buf[6] = laddr;
+ /**
+ * Retries are needed since bus may lose sync when multiple devices
+ * are coming up and reporting present
+ */
+ msg.wbuf = buf;
+ msg.num_bytes = 7;
+
+retry_laddr:
+ ret = slim_processtxn(&dev->ctrl, &txn);
+
+ if (ret) {
+ dev_err(dev->dev, "set LA:0x%x failed:ret:%dretry:%d\n",
+ laddr, ret, retries);
+ if (retries < INIT_MX_RETRIES) {
+ msm_slim_wait_retry(dev);
+ retries++;
+ goto retry_laddr;
+ } else {
+ dev_err(dev->dev, "set LADDR failed:ret:%d\n", ret);
+ }
+ }
+ return ret;
+}
+
+static void msm_slim_rxwq(struct work_struct *work)
+{
+ u8 buf[40];
+ u8 mc, mt, len;
+ int i, ret;
+ struct msm_slim_ctrl *dev = container_of(work, struct msm_slim_ctrl,
+ wd);
+
+ while ((slim_return_rx(&dev->ctrl, buf)) != -ENODATA) {
+ len = buf[0] & 0x1F;
+ mt = (buf[0] >> 5) & 0x7;
+ mc = buf[1];
+ if (mt == SLIM_MSG_MT_CORE &&
+ mc == SLIM_MSG_MC_REPORT_PRESENT) {
+ u8 laddr;
+ struct slim_eaddr ea;
+ u8 e_addr[6];
+
+ for (i = 0; i < 6; i++)
+ e_addr[i] = buf[7-i];
+
+ ea.manf_id = (u16)(e_addr[5] << 8) | e_addr[4];
+ ea.prod_code = (u16)(e_addr[3] << 8) | e_addr[2];
+ ea.dev_index = e_addr[1];
+ ea.instance = e_addr[0];
+ ret = slim_assign_laddr(&dev->ctrl, &ea, &laddr, false);
+ if (ret)
+ dev_err(dev->dev, "assign laddr failed:%d\n",
+ ret);
+ } else {
+ dev_err(dev->dev, "unexpected message:mc:%x, mt:%x\n",
+ mc, mt);
+
+ }
+
+ }
+}
+
+static void msm_slim_prg_slew(struct platform_device *pdev,
+ struct msm_slim_ctrl *dev)
+{
+ void __iomem *slew_reg;
+
+ /* SLEW RATE register for this slimbus */
+ dev->slew_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "slimbus_slew_reg");
+ if (!dev->slew_mem) {
+ dev_warn(&pdev->dev, "no slimbus slew resource\n");
+ return;
+ }
+
+ slew_reg = devm_ioremap(&pdev->dev, dev->slew_mem->start,
+ resource_size(dev->slew_mem));
+ if (!slew_reg) {
+ dev_err(dev->dev, "slew register mapping failed");
+ release_mem_region(dev->slew_mem->start,
+ resource_size(dev->slew_mem));
+ dev->slew_mem = NULL;
+ return;
+ }
+ writel_relaxed(1, slew_reg);
+ /* Make sure slimbus-slew rate enabling goes through */
+ wmb();
+}
+
+static int msm_slim_probe(struct platform_device *pdev)
+{
+ struct msm_slim_ctrl *dev;
+ struct resource *slim_mem;
+ struct resource *irq;
+ struct clk *hclk, *rclk;
+ int ret;
+
+ hclk = devm_clk_get(&pdev->dev, "iface_clk");
+ if (IS_ERR(hclk))
+ return PTR_ERR(hclk);
+
+ rclk = devm_clk_get(&pdev->dev, "core_clk");
+ if (IS_ERR(rclk)) {
+ /* unlikely that this is probe-defer */
+ dev_err(&pdev->dev, "rclk get failed:%ld\n", PTR_ERR(rclk));
+ devm_clk_put(&pdev->dev, hclk);
+ return PTR_ERR(rclk);
+ }
+
+ ret = clk_set_rate(rclk, SLIM_ROOT_FREQ);
+ if (ret) {
+ dev_err(&pdev->dev, "ref-clock set-rate failed:%d\n", ret);
+ return ret;
+ }
+
+ slim_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "slimbus_physical");
+ if (!slim_mem) {
+ dev_err(&pdev->dev, "no slimbus physical memory resource\n");
+ return -ENODEV;
+ }
+
+ irq = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
+ "slimbus_irq");
+ if (!irq) {
+ dev_err(&pdev->dev, "no slimbus IRQ resource\n");
+ return -ENODEV;
+ }
+
+ dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
+ if (!dev)
+ return -ENOMEM;
+
+ dev->hclk = hclk;
+ dev->rclk = rclk;
+
+ dev->dev = &pdev->dev;
+ platform_set_drvdata(pdev, dev);
+ slim_set_ctrldata(&dev->ctrl, dev);
+ dev->base = devm_ioremap(dev->dev, slim_mem->start,
+ resource_size(slim_mem));
+ if (!dev->base) {
+ dev_err(&pdev->dev, "IOremap failed\n");
+ return -ENOMEM;
+ }
+
+ dev->ctrl.set_laddr = msm_set_laddr;
+ dev->ctrl.xfer_msg = msm_xfer_msg;
+ dev->ctrl.tx.n = MSM_TX_MSGS;
+ dev->ctrl.rx.n = MSM_RX_MSGS;
+ dev->ctrl.tx.sl_sz = SLIM_MSGQ_BUF_LEN;
+ dev->ctrl.rx.sl_sz = SLIM_MSGQ_BUF_LEN;
+
+ dev->irq = irq->start;
+
+ INIT_WORK(&dev->wd, msm_slim_rxwq);
+ dev->rxwq = create_singlethread_workqueue("msm_slim_rx");
+ if (!dev->rxwq) {
+ dev_err(dev->dev, "Failed to start Rx WQ\n");
+ return -ENOMEM;
+ }
+
+ dev->framer.rootfreq = SLIM_ROOT_FREQ >> 3;
+ dev->framer.superfreq =
+ dev->framer.rootfreq / SLIM_CL_PER_SUPERFRAME_DIV8;
+ dev->ctrl.a_framer = &dev->framer;
+ dev->ctrl.clkgear = SLIM_MAX_CLK_GEAR;
+ dev->ctrl.dev.parent = &pdev->dev;
+ dev->ctrl.dev.of_node = pdev->dev.of_node;
+
+ msm_slim_prg_slew(pdev, dev);
+
+ ret = devm_request_irq(&pdev->dev, dev->irq, msm_slim_interrupt,
+ IRQF_TRIGGER_HIGH, "msm_slim_irq", dev);
+ if (ret) {
+ dev_err(&pdev->dev, "request IRQ failed\n");
+ goto err_request_irq_failed;
+ }
+
+ ret = clk_prepare_enable(hclk);
+ if (ret)
+ goto err_hclk_enable_failed;
+
+ ret = clk_prepare_enable(rclk);
+ if (ret)
+ goto err_rclk_enable_failed;
+
+ /* Register with framework before enabling frame, clock */
+ ret = slim_register_controller(&dev->ctrl);
+ if (ret) {
+ dev_err(dev->dev, "error adding controller\n");
+ goto err_ctrl_failed;
+ }
+
+ dev->ver = readl_relaxed(dev->base);
+ /* Version info in 16 MSbits */
+ dev->ver >>= 16;
+ /* Component register initialization */
+ writel_relaxed(1, dev->base + CFG_PORT(COMP_CFG, dev->ver));
+ writel_relaxed((EE_MGR_RSC_GRP | EE_NGD_2 | EE_NGD_1),
+ dev->base + CFG_PORT(COMP_TRUST_CFG, dev->ver));
+
+ writel_relaxed((MGR_INT_TX_NACKED_2 |
+ MGR_INT_MSG_BUF_CONTE | MGR_INT_RX_MSG_RCVD |
+ MGR_INT_TX_MSG_SENT), dev->base + MGR_INT_EN);
+ writel_relaxed(1, dev->base + MGR_CFG);
+ /*
+ * Framer registers are beyond 1K memory region after Manager and/or
+ * component registers. Make sure those writes are ordered
+ * before framer register writes
+ */
+ wmb();
+
+ /* Framer register initialization */
+ writel_relaxed((1 << INTR_WAKE) | (0xA << REF_CLK_GEAR) |
+ (0xA << CLK_GEAR) | (1 << ROOT_FREQ) | (1 << FRM_ACTIVE) | 1,
+ dev->base + FRM_CFG);
+ /*
+ * Make sure that framer wake-up and enabling writes go through
+ * before any other component is enabled. Framer is responsible for
+ * clocking the bus and enabling framer first will ensure that other
+ * devices can report presence when they are enabled
+ */
+ mb();
+
+ writel_relaxed(MGR_CFG_ENABLE, dev->base + MGR_CFG);
+ /*
+ * Make sure that manager-enable is written through before interface
+ * device is enabled
+ */
+ mb();
+ writel_relaxed(1, dev->base + INTF_CFG);
+ /*
+ * Make sure that interface-enable is written through before enabling
+ * ported generic device inside MSM manager
+ */
+ mb();
+
+ writel_relaxed(1, dev->base + CFG_PORT(COMP_CFG, dev->ver));
+ /*
+ * Make sure that all writes have gone through before exiting this
+ * function
+ */
+ mb();
+
+ dev_dbg(dev->dev, "MSM SB controller is up:ver:0x%x!\n", dev->ver);
+ return 0;
+
+err_ctrl_failed:
+ clk_disable_unprepare(dev->rclk);
+err_rclk_enable_failed:
+ clk_disable_unprepare(dev->hclk);
+err_hclk_enable_failed:
+err_request_irq_failed:
+ destroy_workqueue(dev->rxwq);
+ return ret;
+}
+
+static int msm_slim_remove(struct platform_device *pdev)
+{
+ struct msm_slim_ctrl *dev = platform_get_drvdata(pdev);
+
+ slim_del_controller(&dev->ctrl);
+ destroy_workqueue(dev->rxwq);
+ return 0;
+}
+
+static const struct of_device_id msm_slim_dt_match[] = {
+ {
+ .compatible = "qcom,slim-msm",
+ },
+ {}
+};
+
+static struct platform_driver msm_slim_driver = {
+ .probe = msm_slim_probe,
+ .remove = msm_slim_remove,
+ .driver = {
+ .name = MSM_SLIM_NAME,
+ .owner = THIS_MODULE,
+ .of_match_table = msm_slim_dt_match,
+ },
+};
+module_platform_driver(msm_slim_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_VERSION("0.1");
+MODULE_DESCRIPTION("Qualcomm Slimbus controller");
+MODULE_ALIAS("platform:qcom-slim");
new file mode 100644
@@ -0,0 +1,65 @@
+/* Copyright (c) 2011-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _SLIM_QCOM_H
+#define _SLIM_QCOM_H
+
+#include <linux/irq.h>
+#include <linux/workqueue.h>
+
+#define QC_MFGID_LSB 0x2
+#define QC_MFGID_MSB 0x17
+
+#define SLIM_MSG_ASM_FIRST_WORD(l, mt, mc, dt, ad) \
+ ((l) | ((mt) << 5) | ((mc) << 8) | ((dt) << 15) | ((ad) << 16))
+
+#define SLIM_ROOT_FREQ 24576000
+#define INIT_MX_RETRIES 10
+#define DEF_RETRY_MS 10
+
+/* MAX message size over control channel */
+#define SLIM_MSGQ_BUF_LEN 40
+#define MSM_TX_MSGS 2
+#define MSM_RX_MSGS 8
+
+#define CFG_PORT(r, v) ((v) ? CFG_PORT_V2(r) : CFG_PORT_V1(r))
+
+/* V2 Component registers */
+#define CFG_PORT_V2(r) ((r ## _V2))
+#define COMP_CFG_V2 4
+#define COMP_TRUST_CFG_V2 0x3000
+
+/* V1 Component registers */
+#define CFG_PORT_V1(r) ((r ## _V1))
+#define COMP_CFG_V1 0
+#define COMP_TRUST_CFG_V1 0x14
+
+/* Resource group info for manager, and non-ported generic device-components */
+#define EE_MGR_RSC_GRP (1 << 10)
+#define EE_NGD_2 (2 << 6)
+#define EE_NGD_1 0
+
+struct msm_slim_ctrl {
+ struct slim_controller ctrl;
+ struct slim_framer framer;
+ struct device *dev;
+ void __iomem *base;
+ struct resource *slew_mem;
+ int irq;
+ struct workqueue_struct *rxwq;
+ struct work_struct wd;
+ struct clk *rclk;
+ struct clk *hclk;
+ u32 ver;
+};
+
+#endif
This controller driver programs manager, interface, and framer devices for Qualcomm's slimbus HW block. Manager component currently implements logical address setting, and messaging interface. Interface device reports bus synchronization information, and framer device clocks the bus from the time it's woken up, until clock-pause is executed by the manager device. Signed-off-by: Sagar Dharia <sdharia@codeaurora.org> --- .../devicetree/bindings/slimbus/slim-qcom-ctrl.txt | 42 ++ drivers/slimbus/Kconfig | 10 + drivers/slimbus/Makefile | 1 + drivers/slimbus/slim-qcom-ctrl.c | 587 +++++++++++++++++++++ drivers/slimbus/slim-qcom.h | 65 +++ 5 files changed, 705 insertions(+) create mode 100644 Documentation/devicetree/bindings/slimbus/slim-qcom-ctrl.txt create mode 100644 drivers/slimbus/slim-qcom-ctrl.c create mode 100644 drivers/slimbus/slim-qcom.h