@@ -195,54 +195,31 @@ static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
qusb2_setbits(qphy->base, QUSB2PHY_PORT_TUNE2, val[0] << 0x4);
}
-static int qusb2_phy_poweron(struct phy *phy)
+static int qusb2_phy_init(struct phy *phy)
{
struct qusb2_phy *qphy = phy_get_drvdata(phy);
- int num = ARRAY_SIZE(qphy->vregs);
+ unsigned int val;
+ unsigned int clk_scheme;
int ret;
- dev_vdbg(&phy->dev, "%s(): Powering-on QUSB2 phy\n", __func__);
+ dev_vdbg(&phy->dev, "%s(): Initializing QUSB2 phy\n", __func__);
/* turn on regulator supplies */
- ret = regulator_bulk_enable(num, qphy->vregs);
+ ret = regulator_bulk_enable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
if (ret)
return ret;
ret = clk_prepare_enable(qphy->iface_clk);
if (ret) {
dev_err(&phy->dev, "failed to enable iface_clk, %d\n", ret);
- regulator_bulk_disable(num, qphy->vregs);
- return ret;
+ goto poweroff_phy;
}
- return 0;
-}
-
-static int qusb2_phy_poweroff(struct phy *phy)
-{
- struct qusb2_phy *qphy = phy_get_drvdata(phy);
-
- clk_disable_unprepare(qphy->iface_clk);
-
- regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
-
- return 0;
-}
-
-static int qusb2_phy_init(struct phy *phy)
-{
- struct qusb2_phy *qphy = phy_get_drvdata(phy);
- unsigned int val;
- unsigned int clk_scheme;
- int ret;
-
- dev_vdbg(&phy->dev, "%s(): Initializing QUSB2 phy\n", __func__);
-
/* enable ahb interface clock to program phy */
ret = clk_prepare_enable(qphy->cfg_ahb_clk);
if (ret) {
dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
- return ret;
+ goto disable_iface_clk;
}
/* Perform phy reset */
@@ -344,6 +321,11 @@ static int qusb2_phy_init(struct phy *phy)
reset_control_assert(qphy->phy_reset);
disable_ahb_clk:
clk_disable_unprepare(qphy->cfg_ahb_clk);
+disable_iface_clk:
+ clk_disable_unprepare(qphy->iface_clk);
+poweroff_phy:
+ regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+
return ret;
}
@@ -361,6 +343,9 @@ static int qusb2_phy_exit(struct phy *phy)
reset_control_assert(qphy->phy_reset);
clk_disable_unprepare(qphy->cfg_ahb_clk);
+ clk_disable_unprepare(qphy->iface_clk);
+
+ regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
return 0;
}
@@ -368,8 +353,6 @@ static int qusb2_phy_exit(struct phy *phy)
static const struct phy_ops qusb2_phy_gen_ops = {
.init = qusb2_phy_init,
.exit = qusb2_phy_exit,
- .power_on = qusb2_phy_poweron,
- .power_off = qusb2_phy_poweroff,
.owner = THIS_MODULE,
};
PHY must be powered on before turning ON clocks and attempting to initialize it. Driver is exposing separate init and power_on routines for this. Apparently USB dwc3 core driver performs power-on after init. Also, poweron and init for QUSB2 PHY need to be executed together always, hence remove poweron callback from phy_ops and explicitly perform this from init, similar changes needed for poweroff. Signed-off-by: Manu Gautam <mgautam@codeaurora.org> --- drivers/phy/qualcomm/phy-qcom-qusb2.c | 47 +++++++++++------------------------ 1 file changed, 15 insertions(+), 32 deletions(-)