| Message ID | 1521193101-4586-3-git-send-email-sricharan@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
On 2018-03-16 15:08, Sricharan R wrote: > Now with the driver updates for some peripherals being there, > add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available > peripheral support. > > Signed-off-by: Sricharan R <sricharan@codeaurora.org> Reviwed-by: Abhishek Sahu <absahu@codeaurora.org> > --- > arch/arm/boot/dts/qcom-ipq4019.dtsi | 134 > ++++++++++++++++++++++++++++++++++++ > 1 file changed, 134 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi > b/arch/arm/boot/dts/qcom-ipq4019.dtsi > index 10d112a..e38fffa 100644 > --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi > +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi > @@ -25,7 +25,9 @@ > > aliases { > spi0 = &spi_0; > + spi1 = &spi_1; > i2c0 = &i2c_0; > + i2c1 = &i2c_1; > }; > > cpus { > @@ -104,6 +106,12 @@ > }; > }; > > + firmware { > + scm { > + compatible = "qcom,scm-ipq4019"; > + }; > + }; > + > timer { > compatible = "arm,armv7-timer"; > interrupts = <1 2 0xf08>, > @@ -172,6 +180,22 @@ > clock-names = "core", "iface"; > #address-cells = <1>; > #size-cells = <0>; > + dmas = <&blsp_dma 5>, <&blsp_dma 4>; > + dma-names = "rx", "tx"; > + status = "disabled"; > + }; > + > + spi_1: spi@78b6000 { /* BLSP1 QUP2 */ > + compatible = "qcom,spi-qup-v2.2.1"; > + reg = <0x78b6000 0x600>; > + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, > + <&gcc GCC_BLSP1_AHB_CLK>; > + clock-names = "core", "iface"; > + #address-cells = <1>; > + #size-cells = <0>; > + dmas = <&blsp_dma 7>, <&blsp_dma 6>; > + dma-names = "rx", "tx"; > status = "disabled"; > }; > > @@ -184,9 +208,24 @@ > clock-names = "iface", "core"; > #address-cells = <1>; > #size-cells = <0>; > + dmas = <&blsp_dma 9>, <&blsp_dma 8>; > + dma-names = "rx", "tx"; > status = "disabled"; > }; > > + i2c_1: i2c@78b8000 { /* BLSP1 QUP4 */ > + compatible = "qcom,i2c-qup-v2.2.1"; > + reg = <0x78b8000 0x600>; > + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_AHB_CLK>, > + <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; > + clock-names = "iface", "core"; > + #address-cells = <1>; > + #size-cells = <0>; > + dmas = <&blsp_dma 11>, <&blsp_dma 10>; > + dma-names = "rx", "tx"; > + status = "disabled"; > + }; > > cryptobam: dma@8e04000 { > compatible = "qcom,bam-v1.7.0"; > @@ -293,6 +332,101 @@ > reg = <0x4ab000 0x4>; > }; > > + pcie0: pci@40000000 { > + compatible = "qcom,pcie-ipq4019", "snps,dw-pcie"; > + reg = <0x40000000 0xf1d > + 0x40000f20 0xa8 > + 0x80000 0x2000 > + 0x40100000 0x1000>; > + reg-names = "dbi", "elbi", "parf", "config"; > + device_type = "pci"; > + linux,pci-domain = <0>; > + bus-range = <0x00 0xff>; > + num-lanes = <1>; > + #address-cells = <3>; > + #size-cells = <2>; > + > + ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000 > + 0x82000000 0 0x48000000 0x48000000 0 0x10000000>; > + > + interrupts = <GIC_SPI 141 IRQ_TYPE_NONE>; > + interrupt-names = "msi"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0x7>; > + interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a > */ > + <0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ > + <0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ > + <0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ > + clocks = <&gcc GCC_PCIE_AHB_CLK>, > + <&gcc GCC_PCIE_AXI_M_CLK>, > + <&gcc GCC_PCIE_AXI_S_CLK>; > + clock-names = "aux", > + "master_bus", > + "slave_bus"; > + > + resets = <&gcc PCIE_AXI_M_ARES>, > + <&gcc PCIE_AXI_S_ARES>, > + <&gcc PCIE_PIPE_ARES>, > + <&gcc PCIE_AXI_M_VMIDMT_ARES>, > + <&gcc PCIE_AXI_S_XPU_ARES>, > + <&gcc PCIE_PARF_XPU_ARES>, > + <&gcc PCIE_PHY_ARES>, > + <&gcc PCIE_AXI_M_STICKY_ARES>, > + <&gcc PCIE_PIPE_STICKY_ARES>, > + <&gcc PCIE_PWR_ARES>, > + <&gcc PCIE_AHB_ARES>, > + <&gcc PCIE_PHY_AHB_ARES>; > + reset-names = "axi_m", > + "axi_s", > + "pipe", > + "axi_m_vmid", > + "axi_s_xpu", > + "parf", > + "phy", > + "axi_m_sticky", > + "pipe_sticky", > + "pwr", > + "ahb", > + "phy_ahb"; > + > + status = "disabled"; > + }; > + > + qpic_bam: dma@7984000 { > + compatible = "qcom,bam-v1.7.0"; > + reg = <0x7984000 0x1a000>; > + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_QPIC_CLK>; > + clock-names = "bam_clk"; > + #dma-cells = <1>; > + qcom,ee = <0>; > + status = "disabled"; > + }; > + > + nand: qpic-nand@79b0000 { > + compatible = "qcom,ipq4019-nand"; > + reg = <0x79b0000 0x1000>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&gcc GCC_QPIC_CLK>, > + <&gcc GCC_QPIC_AHB_CLK>; > + clock-names = "core", "aon"; > + > + dmas = <&qpic_bam 0>, > + <&qpic_bam 1>, > + <&qpic_bam 2>; > + dma-names = "tx", "rx", "cmd"; > + status = "disabled"; > + > + nand@0 { > + reg = <0>; > + > + nand-ecc-strength = <4>; > + nand-ecc-step-size = <512>; > + nand-bus-width = <8>; > + }; > + }; > + > wifi0: wifi@a000000 { > compatible = "qcom,ipq4019-wifi"; > reg = <0xa000000 0x200000>; -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 2018-03-16 15:08, Sricharan R wrote: > Now with the driver updates for some peripherals being there, > add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available > peripheral support. > > Signed-off-by: Sricharan R <sricharan@codeaurora.org> Reviewed-by: Abhishek Sahu <absahu@codeaurora.org> > --- > arch/arm/boot/dts/qcom-ipq4019.dtsi | 134 > ++++++++++++++++++++++++++++++++++++ > 1 file changed, 134 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi > b/arch/arm/boot/dts/qcom-ipq4019.dtsi > index 10d112a..e38fffa 100644 > --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi > +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi > @@ -25,7 +25,9 @@ > > aliases { > spi0 = &spi_0; > + spi1 = &spi_1; > i2c0 = &i2c_0; > + i2c1 = &i2c_1; > }; > > cpus { > @@ -104,6 +106,12 @@ > }; > }; > > + firmware { > + scm { > + compatible = "qcom,scm-ipq4019"; > + }; > + }; > + > timer { > compatible = "arm,armv7-timer"; > interrupts = <1 2 0xf08>, > @@ -172,6 +180,22 @@ > clock-names = "core", "iface"; > #address-cells = <1>; > #size-cells = <0>; > + dmas = <&blsp_dma 5>, <&blsp_dma 4>; > + dma-names = "rx", "tx"; > + status = "disabled"; > + }; > + > + spi_1: spi@78b6000 { /* BLSP1 QUP2 */ > + compatible = "qcom,spi-qup-v2.2.1"; > + reg = <0x78b6000 0x600>; > + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, > + <&gcc GCC_BLSP1_AHB_CLK>; > + clock-names = "core", "iface"; > + #address-cells = <1>; > + #size-cells = <0>; > + dmas = <&blsp_dma 7>, <&blsp_dma 6>; > + dma-names = "rx", "tx"; > status = "disabled"; > }; > > @@ -184,9 +208,24 @@ > clock-names = "iface", "core"; > #address-cells = <1>; > #size-cells = <0>; > + dmas = <&blsp_dma 9>, <&blsp_dma 8>; > + dma-names = "rx", "tx"; > status = "disabled"; > }; > > + i2c_1: i2c@78b8000 { /* BLSP1 QUP4 */ > + compatible = "qcom,i2c-qup-v2.2.1"; > + reg = <0x78b8000 0x600>; > + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_AHB_CLK>, > + <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; > + clock-names = "iface", "core"; > + #address-cells = <1>; > + #size-cells = <0>; > + dmas = <&blsp_dma 11>, <&blsp_dma 10>; > + dma-names = "rx", "tx"; > + status = "disabled"; > + }; > > cryptobam: dma@8e04000 { > compatible = "qcom,bam-v1.7.0"; > @@ -293,6 +332,101 @@ > reg = <0x4ab000 0x4>; > }; > > + pcie0: pci@40000000 { > + compatible = "qcom,pcie-ipq4019", "snps,dw-pcie"; > + reg = <0x40000000 0xf1d > + 0x40000f20 0xa8 > + 0x80000 0x2000 > + 0x40100000 0x1000>; > + reg-names = "dbi", "elbi", "parf", "config"; > + device_type = "pci"; > + linux,pci-domain = <0>; > + bus-range = <0x00 0xff>; > + num-lanes = <1>; > + #address-cells = <3>; > + #size-cells = <2>; > + > + ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000 > + 0x82000000 0 0x48000000 0x48000000 0 0x10000000>; > + > + interrupts = <GIC_SPI 141 IRQ_TYPE_NONE>; > + interrupt-names = "msi"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0x7>; > + interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a > */ > + <0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ > + <0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ > + <0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ > + clocks = <&gcc GCC_PCIE_AHB_CLK>, > + <&gcc GCC_PCIE_AXI_M_CLK>, > + <&gcc GCC_PCIE_AXI_S_CLK>; > + clock-names = "aux", > + "master_bus", > + "slave_bus"; > + > + resets = <&gcc PCIE_AXI_M_ARES>, > + <&gcc PCIE_AXI_S_ARES>, > + <&gcc PCIE_PIPE_ARES>, > + <&gcc PCIE_AXI_M_VMIDMT_ARES>, > + <&gcc PCIE_AXI_S_XPU_ARES>, > + <&gcc PCIE_PARF_XPU_ARES>, > + <&gcc PCIE_PHY_ARES>, > + <&gcc PCIE_AXI_M_STICKY_ARES>, > + <&gcc PCIE_PIPE_STICKY_ARES>, > + <&gcc PCIE_PWR_ARES>, > + <&gcc PCIE_AHB_ARES>, > + <&gcc PCIE_PHY_AHB_ARES>; > + reset-names = "axi_m", > + "axi_s", > + "pipe", > + "axi_m_vmid", > + "axi_s_xpu", > + "parf", > + "phy", > + "axi_m_sticky", > + "pipe_sticky", > + "pwr", > + "ahb", > + "phy_ahb"; > + > + status = "disabled"; > + }; > + > + qpic_bam: dma@7984000 { > + compatible = "qcom,bam-v1.7.0"; > + reg = <0x7984000 0x1a000>; > + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_QPIC_CLK>; > + clock-names = "bam_clk"; > + #dma-cells = <1>; > + qcom,ee = <0>; > + status = "disabled"; > + }; > + > + nand: qpic-nand@79b0000 { > + compatible = "qcom,ipq4019-nand"; > + reg = <0x79b0000 0x1000>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&gcc GCC_QPIC_CLK>, > + <&gcc GCC_QPIC_AHB_CLK>; > + clock-names = "core", "aon"; > + > + dmas = <&qpic_bam 0>, > + <&qpic_bam 1>, > + <&qpic_bam 2>; > + dma-names = "tx", "rx", "cmd"; > + status = "disabled"; > + > + nand@0 { > + reg = <0>; > + > + nand-ecc-strength = <4>; > + nand-ecc-step-size = <512>; > + nand-bus-width = <8>; > + }; > + }; > + > wifi0: wifi@a000000 { > compatible = "qcom,ipq4019-wifi"; > reg = <0xa000000 0x200000>; -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 16/03/18 09:38, Sricharan R wrote: > Now with the driver updates for some peripherals being there, > add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available > peripheral support. > > Signed-off-by: Sricharan R <sricharan@codeaurora.org> > --- > arch/arm/boot/dts/qcom-ipq4019.dtsi | 134 ++++++++++++++++++++++++++++++++++++ > 1 file changed, 134 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi > index 10d112a..e38fffa 100644 > --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi > +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi > @@ -25,7 +25,9 @@ [...] > + pcie0: pci@40000000 { > + compatible = "qcom,pcie-ipq4019", "snps,dw-pcie"; > + reg = <0x40000000 0xf1d > + 0x40000f20 0xa8 > + 0x80000 0x2000 > + 0x40100000 0x1000>; > + reg-names = "dbi", "elbi", "parf", "config"; > + device_type = "pci"; > + linux,pci-domain = <0>; > + bus-range = <0x00 0xff>; > + num-lanes = <1>; > + #address-cells = <3>; > + #size-cells = <2>; > + > + ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000 > + 0x82000000 0 0x48000000 0x48000000 0 0x10000000>; > + > + interrupts = <GIC_SPI 141 IRQ_TYPE_NONE>; There is no such thing as IRQ_TYPE_NONE. Please replace this with the actual trigger information. Thanks, M.
Hi Marc, On 3/16/2018 5:47 PM, Marc Zyngier wrote: > On 16/03/18 09:38, Sricharan R wrote: >> Now with the driver updates for some peripherals being there, >> add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available >> peripheral support. >> >> Signed-off-by: Sricharan R <sricharan@codeaurora.org> >> --- >> arch/arm/boot/dts/qcom-ipq4019.dtsi | 134 ++++++++++++++++++++++++++++++++++++ >> 1 file changed, 134 insertions(+) >> >> diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi >> index 10d112a..e38fffa 100644 >> --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi >> +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi >> @@ -25,7 +25,9 @@ > > [...] > >> + pcie0: pci@40000000 { >> + compatible = "qcom,pcie-ipq4019", "snps,dw-pcie"; >> + reg = <0x40000000 0xf1d >> + 0x40000f20 0xa8 >> + 0x80000 0x2000 >> + 0x40100000 0x1000>; >> + reg-names = "dbi", "elbi", "parf", "config"; >> + device_type = "pci"; >> + linux,pci-domain = <0>; >> + bus-range = <0x00 0xff>; >> + num-lanes = <1>; >> + #address-cells = <3>; >> + #size-cells = <2>; >> + >> + ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000 >> + 0x82000000 0 0x48000000 0x48000000 0 0x10000000>; >> + >> + interrupts = <GIC_SPI 141 IRQ_TYPE_NONE>; > > There is no such thing as IRQ_TYPE_NONE. Please replace this with the > actual trigger information. ok, will update this. Regards, Sricharan
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi index 10d112a..e38fffa 100644 --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi @@ -25,7 +25,9 @@ aliases { spi0 = &spi_0; + spi1 = &spi_1; i2c0 = &i2c_0; + i2c1 = &i2c_1; }; cpus { @@ -104,6 +106,12 @@ }; }; + firmware { + scm { + compatible = "qcom,scm-ipq4019"; + }; + }; + timer { compatible = "arm,armv7-timer"; interrupts = <1 2 0xf08>, @@ -172,6 +180,22 @@ clock-names = "core", "iface"; #address-cells = <1>; #size-cells = <0>; + dmas = <&blsp_dma 5>, <&blsp_dma 4>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + spi_1: spi@78b6000 { /* BLSP1 QUP2 */ + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x78b6000 0x600>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&blsp_dma 7>, <&blsp_dma 6>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -184,9 +208,24 @@ clock-names = "iface", "core"; #address-cells = <1>; #size-cells = <0>; + dmas = <&blsp_dma 9>, <&blsp_dma 8>; + dma-names = "rx", "tx"; status = "disabled"; }; + i2c_1: i2c@78b8000 { /* BLSP1 QUP4 */ + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x78b8000 0x600>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; + clock-names = "iface", "core"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&blsp_dma 11>, <&blsp_dma 10>; + dma-names = "rx", "tx"; + status = "disabled"; + }; cryptobam: dma@8e04000 { compatible = "qcom,bam-v1.7.0"; @@ -293,6 +332,101 @@ reg = <0x4ab000 0x4>; }; + pcie0: pci@40000000 { + compatible = "qcom,pcie-ipq4019", "snps,dw-pcie"; + reg = <0x40000000 0xf1d + 0x40000f20 0xa8 + 0x80000 0x2000 + 0x40100000 0x1000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000 + 0x82000000 0 0x48000000 0x48000000 0 0x10000000>; + + interrupts = <GIC_SPI 141 IRQ_TYPE_NONE>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc GCC_PCIE_AHB_CLK>, + <&gcc GCC_PCIE_AXI_M_CLK>, + <&gcc GCC_PCIE_AXI_S_CLK>; + clock-names = "aux", + "master_bus", + "slave_bus"; + + resets = <&gcc PCIE_AXI_M_ARES>, + <&gcc PCIE_AXI_S_ARES>, + <&gcc PCIE_PIPE_ARES>, + <&gcc PCIE_AXI_M_VMIDMT_ARES>, + <&gcc PCIE_AXI_S_XPU_ARES>, + <&gcc PCIE_PARF_XPU_ARES>, + <&gcc PCIE_PHY_ARES>, + <&gcc PCIE_AXI_M_STICKY_ARES>, + <&gcc PCIE_PIPE_STICKY_ARES>, + <&gcc PCIE_PWR_ARES>, + <&gcc PCIE_AHB_ARES>, + <&gcc PCIE_PHY_AHB_ARES>; + reset-names = "axi_m", + "axi_s", + "pipe", + "axi_m_vmid", + "axi_s_xpu", + "parf", + "phy", + "axi_m_sticky", + "pipe_sticky", + "pwr", + "ahb", + "phy_ahb"; + + status = "disabled"; + }; + + qpic_bam: dma@7984000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x7984000 0x1a000>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_QPIC_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + status = "disabled"; + }; + + nand: qpic-nand@79b0000 { + compatible = "qcom,ipq4019-nand"; + reg = <0x79b0000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&gcc GCC_QPIC_CLK>, + <&gcc GCC_QPIC_AHB_CLK>; + clock-names = "core", "aon"; + + dmas = <&qpic_bam 0>, + <&qpic_bam 1>, + <&qpic_bam 2>; + dma-names = "tx", "rx", "cmd"; + status = "disabled"; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + }; + }; + wifi0: wifi@a000000 { compatible = "qcom,ipq4019-wifi"; reg = <0xa000000 0x200000>;
Now with the driver updates for some peripherals being there, add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available peripheral support. Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- arch/arm/boot/dts/qcom-ipq4019.dtsi | 134 ++++++++++++++++++++++++++++++++++++ 1 file changed, 134 insertions(+)