deleted file mode 100644
@@ -1,217 +0,0 @@
-Qualcomm Technologies, Inc.
-dpu-dp is the master Display Port device which supports DP host controllers that are compatible with VESA Display Port interface specification.
-DP Controller: Required properties:
-- compatible: Should be "qcom,dp-display".
-- reg: Base address and length of DP hardware's memory mapped regions.
-- reg-names: A list of strings that name the list of regs. "dp_ctrl" - DP controller memory region.
- "dp_phy" - DP PHY memory region.
- "dp_ln_tx0" - USB3 DP PHY combo TX-0 lane memory region.
- "dp_ln_tx1" - USB3 DP PHY combo TX-1 lane memory region.
- "dp_mmss_cc" - Display Clock Control memory region.
- "qfprom_physical" - QFPROM Phys memory region.
- "dp_pll" - USB3 DP combo PLL memory region.
- "usb3_dp_com" - USB3 DP PHY combo memory region.
- "hdcp_physical" - DP HDCP memory region.
-- cell-index: Specifies the controller instance.
-- clocks: Clocks required for Display Port operation.
-- clock-names: Names of the clocks corresponding to handles. Following clocks are required:
- "core_aux_clk", "core_usb_ref_clk_src","core_usb_ref_clk", "core_usb_cfg_ahb_clk",
- "core_usb_pipe_clk", "ctrl_link_clk", "ctrl_link_iface_clk", "ctrl_crypto_clk",
- "ctrl_pixel_clk", "pixel_clk_rcg", "pixel_parent".
-- gdsc-supply: phandle to gdsc regulator node.
-- vdda-1p2-supply: phandle to vdda 1.2V regulator node.
-- vdda-0p9-supply: phandle to vdda 0.9V regulator node.
-- interrupt-parent phandle to the interrupt parent device node.
-- interrupts: The interrupt signal from the DSI block.
-- qcom,aux-en-gpio: Specifies the aux-channel enable gpio.
-- qcom,aux-sel-gpio: Specifies the aux-channel select gpio.
-- qcom,usbplug-cc-gpio: Specifies the usbplug orientation gpio.
-- qcom,aux-cfg0-settings: Specifies the DP AUX configuration 0 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg1-settings: Specifies the DP AUX configuration 1 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg2-settings: Specifies the DP AUX configuration 2 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg3-settings: Specifies the DP AUX configuration 3 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg4-settings: Specifies the DP AUX configuration 4 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg5-settings: Specifies the DP AUX configuration 5 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg6-settings: Specifies the DP AUX configuration 6 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg7-settings: Specifies the DP AUX configuration 7 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg8-settings: Specifies the DP AUX configuration 8 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,aux-cfg9-settings: Specifies the DP AUX configuration 9 settings. The first
- entry in this array corresponds to the register offset
- within DP AUX, while the remaining entries indicate the
- programmable values.
-- qcom,max-pclk-frequency-khz: An integer specifying the max. pixel clock in KHz supported by Display Port.
-- qcom,dp-usbpd-detection: Phandle for the PMI regulator node for USB PHY PD detection.
-- qcom,<type>-supply-entries: A node that lists the elements of the supply used by the a particular "type" of DSI module. The module "types"
- can be "core", "ctrl", and "phy". Within the same type,
- there can be more than one instance of this binding,
- in which case the entry would be appended with the
- supply entry index.
- e.g. qcom,ctrl-supply-entry@0
- -- qcom,supply-name: name of the supply (vdd/vdda/vddio)
- -- qcom,supply-min-voltage: minimum voltage level (uV)
- -- qcom,supply-max-voltage: maximum voltage level (uV)
- -- qcom,supply-enable-load: load drawn (uA) from enabled supply
- -- qcom,supply-disable-load: load drawn (uA) from disabled supply
- -- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
- -- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
- -- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
- -- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
-- pinctrl-names: List of names to assign mdss pin states defined in pinctrl device node
- Refer to pinctrl-bindings.txt
-- pinctrl-<0..n>: Lists phandles each pointing to the pin configuration node within a pin
- controller. These pin configurations are installed in the pinctrl
- device node. Refer to pinctrl-bindings.txt
-
-msm_ext_disp is a device which manages the interaction between external
-display interfaces, e.g. Display Port, and the audio subsystem.
-
-Optional properties:
-- qcom,ext-disp: phandle for msm-ext-display module
-- compatible: Must be "qcom,msm-ext-disp"
-
-[Optional child nodes]: These nodes are for devices which are
-dependent on msm_ext_disp. If msm_ext_disp is disabled then
-these devices will be disabled as well. Ex. Audio Codec device.
-
-- ext_disp_audio_codec: Node for Audio Codec.
-- compatible : "qcom,msm-ext-disp-audio-codec-rx";
-
-Example:
- ext_disp: qcom,msm-ext-disp {
- compatible = "qcom,msm-ext-disp";
- ext_disp_audio_codec: qcom,msm-ext-disp-audio-codec-rx {
- compatible = "qcom,msm-ext-disp-audio-codec-rx";
- };
- };
-
- dpu_dp: qcom,dp_display@0{
- cell-index = <0>;
- compatible = "qcom,dp-display";
-
- gdsc-supply = <&mdss_core_gdsc>;
- vdda-1p2-supply = <&pm8998_l26>;
- vdda-0p9-supply = <&pm8998_l1>;
-
- reg = <0xae90000 0xa84>,
- <0x88eaa00 0x200>,
- <0x88ea200 0x200>,
- <0x88ea600 0x200>,
- <0xaf02000 0x1a0>,
- <0x780000 0x621c>,
- <0x88ea030 0x10>,
- <0x88e8000 0x621c>,
- <0x0aee1000 0x034>;
- reg-names = "dp_ctrl", "dp_phy", "dp_ln_tx0", "dp_ln_tx1",
- "dp_mmss_cc", "qfprom_physical", "dp_pll",
- "usb3_dp_com", "hdcp_physical";
-
- interrupt-parent = <&mdss_mdp>;
- interrupts = <12 0>;
-
- clocks = <&clock_dispcc DISP_CC_MDSS_DP_AUX_CLK>,
- <&clock_rpmh RPMH_CXO_CLK>,
- <&clock_gcc GCC_USB3_PRIM_CLKREF_CLK>,
- <&clock_gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
- <&clock_gcc GCC_USB3_PRIM_PHY_PIPE_CLK>,
- <&clock_dispcc DISP_CC_MDSS_DP_LINK_CLK>,
- <&clock_dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
- <&clock_dispcc DISP_CC_MDSS_DP_CRYPTO_CLK>,
- <&clock_dispcc DISP_CC_MDSS_DP_PIXEL_CLK>,
- <&clock_dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>,
- <&mdss_dp_pll DP_VCO_DIVIDED_CLK_SRC_MUX>;
- clock-names = "core_aux_clk", "core_usb_ref_clk_src",
- "core_usb_ref_clk", "core_usb_cfg_ahb_clk",
- "core_usb_pipe_clk", "ctrl_link_clk",
- "ctrl_link_iface_clk", "ctrl_crypto_clk",
- "ctrl_pixel_clk", "pixel_clk_rcg", "pixel_parent";
-
- qcom,dp-usbpd-detection = <&pmi8998_pdphy>;
- qcom,ext-disp = <&ext_disp>;
-
- qcom,aux-cfg0-settings = [1c 00];
- qcom,aux-cfg1-settings = [20 13 23 1d];
- qcom,aux-cfg2-settings = [24 00];
- qcom,aux-cfg3-settings = [28 00];
- qcom,aux-cfg4-settings = [2c 0a];
- qcom,aux-cfg5-settings = [30 26];
- qcom,aux-cfg6-settings = [34 0a];
- qcom,aux-cfg7-settings = [38 03];
- qcom,aux-cfg8-settings = [3c bb];
- qcom,aux-cfg9-settings = [40 03];
- qcom,max-pclk-frequency-khz = <593470>;
- pinctrl-names = "mdss_dp_active", "mdss_dp_sleep";
- pinctrl-0 = <&dpu_dp_aux_active &dpu_dp_usbplug_cc_active>;
- pinctrl-1 = <&dpu_dp_aux_suspend &dpu_dp_usbplug_cc_suspend>;
- qcom,aux-en-gpio = <&tlmm 43 0>;
- qcom,aux-sel-gpio = <&tlmm 51 0>;
- qcom,usbplug-cc-gpio = <&tlmm 38 0>;
- qcom,core-supply-entries {
- #address-cells = <1>;
- #size-cells = <0>;
-
- qcom,core-supply-entry@0 {
- reg = <0>;
- qcom,supply-name = "gdsc";
- qcom,supply-min-voltage = <0>;
- qcom,supply-max-voltage = <0>;
- qcom,supply-enable-load = <0>;
- qcom,supply-disable-load = <0>;
- };
- };
-
- qcom,ctrl-supply-entries {
- #address-cells = <1>;
- #size-cells = <0>;
-
- qcom,ctrl-supply-entry@0 {
- reg = <0>;
- qcom,supply-name = "vdda-1p2";
- qcom,supply-min-voltage = <1200000>;
- qcom,supply-max-voltage = <1200000>;
- qcom,supply-enable-load = <21800>;
- qcom,supply-disable-load = <4>;
- };
- };
-
- qcom,phy-supply-entries {
- #address-cells = <1>;
- #size-cells = <0>;
-
- qcom,phy-supply-entry@0 {
- reg = <0>;
- qcom,supply-name = "vdda-0p9";
- qcom,supply-min-voltage = <880000>;
- qcom,supply-max-voltage = <880000>;
- qcom,supply-enable-load = <36000>;
- qcom,supply-disable-load = <32>;
- };
- };
- };
-};
DPU display port driver is not enabled yet so removing the bindings. The driver code is also reverted. The bindings will be added back when display port driver is reworked and enabled for sdm845. Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org> --- .../devicetree/bindings/drm/msm/dpu-dp.txt | 217 --------------------- 1 file changed, 217 deletions(-) delete mode 100644 Documentation/devicetree/bindings/drm/msm/dpu-dp.txt