| Message ID | 1529406822-15379-4-git-send-email-kgunda@codeaurora.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
On Tue 19 Jun 04:13 PDT 2018, Kiran Gunda wrote: > diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt [..] > - qcom,num-strings > Usage: optional > Value type: <u32> > Definition: #; number of led strings attached; > - value from 1 to 3. default: 2 > - This property is supported only for PM8941. > + value: For PM8941 from 1 to 3. default: 2 > + For PMI8998 from 1 to 4. default: 4 [..] > +- qcom,enabled-strings > + Usage: optional > + Value tyoe: <u32 array> > + Definition: Array of the WLED strings numbered from 0 to 3. Each > + string of leds are operated individually. Specify the > + list of strings used by the device. Any combination of > + led strings can be used. > + for pm8941: Default values are [00 01]. > + for pmi8998: Default values are [00 01 02 03]. I would suggest omitting the defaults, as we can see in several places in this document we end up having to update the document with new defaults for each platform. Also, per the defaults of the optional qcom,num-strings these are already the defaults... [..] > +pmi8998-wled@d800 { > + compatible = "qcom,pmi8998-wled"; > + reg = <0xd800 0xd900>; > + label = "backlight"; > + > + interrupts = <3 0xd8 2 IRQ_TYPE_EDGE_RISING>, > + <3 0xd8 1 IRQ_TYPE_EDGE_RISING>; > + interrupt-names = "short", "ovp"; > + qcom,current-limit-microamp = <25000>; > + qcom,current-boost-limit = <805>; > + qcom,switching-freq = <1600>; > + qcom,ovp-millivolt = <29600>; > + qcom,num-strings = <4>; > + qcom,enabled-strings = <0x00 0x01 0x02 0x03>; Please omit the pmi8998 example as well, there's no real benefit of adding similar examples for each platform. Regards, Bjorn -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 2018-06-20 04:33, Bjorn Andersson wrote: > On Tue 19 Jun 04:13 PDT 2018, Kiran Gunda wrote: >> diff --git >> a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt >> b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt > [..] >> - qcom,num-strings >> Usage: optional >> Value type: <u32> >> Definition: #; number of led strings attached; >> - value from 1 to 3. default: 2 >> - This property is supported only for PM8941. >> + value: For PM8941 from 1 to 3. default: 2 >> + For PMI8998 from 1 to 4. default: 4 > [..] >> +- qcom,enabled-strings >> + Usage: optional >> + Value tyoe: <u32 array> >> + Definition: Array of the WLED strings numbered from 0 to 3. Each >> + string of leds are operated individually. Specify the >> + list of strings used by the device. Any combination of >> + led strings can be used. >> + for pm8941: Default values are [00 01]. >> + for pmi8998: Default values are [00 01 02 03]. > > I would suggest omitting the defaults, as we can see in several places > in this document we end up having to update the document with new > defaults for each platform. > > Also, per the defaults of the optional qcom,num-strings these are > already the defaults... > Sure. I will remove the defaults in the next series. > [..] >> +pmi8998-wled@d800 { >> + compatible = "qcom,pmi8998-wled"; >> + reg = <0xd800 0xd900>; >> + label = "backlight"; >> + >> + interrupts = <3 0xd8 2 IRQ_TYPE_EDGE_RISING>, >> + <3 0xd8 1 IRQ_TYPE_EDGE_RISING>; >> + interrupt-names = "short", "ovp"; >> + qcom,current-limit-microamp = <25000>; >> + qcom,current-boost-limit = <805>; >> + qcom,switching-freq = <1600>; >> + qcom,ovp-millivolt = <29600>; >> + qcom,num-strings = <4>; >> + qcom,enabled-strings = <0x00 0x01 0x02 0x03>; > > Please omit the pmi8998 example as well, there's no real benefit of > adding similar examples for each platform. > Sure. I will remove it. > Regards, > Bjorn -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Jun 19, 2018 at 04:43:38PM +0530, Kiran Gunda wrote: > Update the bindings with the new properties used for > PMI8998. > > Signed-off-by: Kiran Gunda <kgunda@codeaurora.org> > --- > .../bindings/leds/backlight/qcom-wled.txt | 84 ++++++++++++++++++++-- > 1 file changed, 77 insertions(+), 7 deletions(-) > > diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt > index 14f28f2..503ce87 100644 > --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt > +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt > @@ -48,11 +48,15 @@ platforms. The PMIC is connected to the host processor via SPMI bus. > - qcom,current-limit > Usage: optional > Value type: <u32> > - Definition: mA; per-string current limit > - value: For pm8941: from 0 to 25 with 5 mA step > - Default 20 mA. > - For pmi8998: from 0 to 30 with 5 mA step > - Default 25 mA. > + Definition: mA; per-string current limit; value from 0 to 25 with > + 1 mA step. Default 20 mA. > + This property is supported only for pm8941. > + > +- qcom,current-limit-microamp > + Usage: optional > + Value type: <u32> > + Definition: uA; per-string current limit; value from 0 to 30000 with > + 2500 uA step. Default 25000 uA. This doesn't really seem worth adding just to add '-microamp'. > - qcom,current-boost-limit > Usage: optional > @@ -79,12 +83,61 @@ platforms. The PMIC is connected to the host processor via SPMI bus. > 27, 29, 32, 35. default: 29V > This property is supported only for PM8941. > > +- qcom,ovp-millivolt Is this the same as qcom,ovp? If so, same comment. > + Usage: optional > + Value type: <u32> > + Definition: mV; Over-voltage protection limit; > + For pmi8998: one of 18100, 19600, 29600, 31100 > + Default: 29600 mV > + If this property is not specified for PM8941, it > + falls back to "qcom,ovp" property. > + > - qcom,num-strings > Usage: optional > Value type: <u32> > Definition: #; number of led strings attached; > - value from 1 to 3. default: 2 > - This property is supported only for PM8941. > + value: For PM8941 from 1 to 3. default: 2 > + For PMI8998 from 1 to 4. default: 4 > + > +- interrupts > + Usage: optional > + Value type: <prop encoded array> > + Definition: Interrupts associated with WLED. This should be > + "short" and "ovp" interrupts. Interrupts can be > + specified as per the encoding listed under > + Documentation/devicetree/bindings/spmi/ > + qcom,spmi-pmic-arb.txt. > + > +- interrupt-names > + Usage: optional > + Value type: <string> > + Definition: Interrupt names associated with the interrupts. > + Must be "short" and "ovp". The short circuit detection > + is not supported for PM8941. > + > +- qcom,enabled-strings > + Usage: optional > + Value tyoe: <u32 array> > + Definition: Array of the WLED strings numbered from 0 to 3. Each > + string of leds are operated individually. Specify the > + list of strings used by the device. Any combination of > + led strings can be used. > + for pm8941: Default values are [00 01]. > + for pmi8998: Default values are [00 01 02 03]. u32 or u8 because dts syntax for 8-bit array is []. > + > +- qcom,external-pfet > + Usage: optional > + Value type: <bool> > + Definition: Specify if external PFET control for short circuit > + protection is used. This property is supported only > + for PMI8998. > + > +- qcom,auto-string-detection > + Usage: optional > + Value type: <bool> > + Definition: Enables auto-detection of the WLED string configuration. > + This feature is not supported for PM8941. > + > > Example: > > @@ -99,4 +152,21 @@ pm8941-wled@d800 { > qcom,switching-freq = <1600>; > qcom,ovp = <29>; > qcom,num-strings = <2>; > + qcom,enabled-strings = <0x00 0x01>; > +}; > + > +pmi8998-wled@d800 { led-controller { And needs a unit-address. > + compatible = "qcom,pmi8998-wled"; > + reg = <0xd800 0xd900>; > + label = "backlight"; > + > + interrupts = <3 0xd8 2 IRQ_TYPE_EDGE_RISING>, > + <3 0xd8 1 IRQ_TYPE_EDGE_RISING>; > + interrupt-names = "short", "ovp"; > + qcom,current-limit-microamp = <25000>; > + qcom,current-boost-limit = <805>; > + qcom,switching-freq = <1600>; > + qcom,ovp-millivolt = <29600>; > + qcom,num-strings = <4>; > + qcom,enabled-strings = <0x00 0x01 0x02 0x03>; > }; > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project > -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt index 14f28f2..503ce87 100644 --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt @@ -48,11 +48,15 @@ platforms. The PMIC is connected to the host processor via SPMI bus. - qcom,current-limit Usage: optional Value type: <u32> - Definition: mA; per-string current limit - value: For pm8941: from 0 to 25 with 5 mA step - Default 20 mA. - For pmi8998: from 0 to 30 with 5 mA step - Default 25 mA. + Definition: mA; per-string current limit; value from 0 to 25 with + 1 mA step. Default 20 mA. + This property is supported only for pm8941. + +- qcom,current-limit-microamp + Usage: optional + Value type: <u32> + Definition: uA; per-string current limit; value from 0 to 30000 with + 2500 uA step. Default 25000 uA. - qcom,current-boost-limit Usage: optional @@ -79,12 +83,61 @@ platforms. The PMIC is connected to the host processor via SPMI bus. 27, 29, 32, 35. default: 29V This property is supported only for PM8941. +- qcom,ovp-millivolt + Usage: optional + Value type: <u32> + Definition: mV; Over-voltage protection limit; + For pmi8998: one of 18100, 19600, 29600, 31100 + Default: 29600 mV + If this property is not specified for PM8941, it + falls back to "qcom,ovp" property. + - qcom,num-strings Usage: optional Value type: <u32> Definition: #; number of led strings attached; - value from 1 to 3. default: 2 - This property is supported only for PM8941. + value: For PM8941 from 1 to 3. default: 2 + For PMI8998 from 1 to 4. default: 4 + +- interrupts + Usage: optional + Value type: <prop encoded array> + Definition: Interrupts associated with WLED. This should be + "short" and "ovp" interrupts. Interrupts can be + specified as per the encoding listed under + Documentation/devicetree/bindings/spmi/ + qcom,spmi-pmic-arb.txt. + +- interrupt-names + Usage: optional + Value type: <string> + Definition: Interrupt names associated with the interrupts. + Must be "short" and "ovp". The short circuit detection + is not supported for PM8941. + +- qcom,enabled-strings + Usage: optional + Value tyoe: <u32 array> + Definition: Array of the WLED strings numbered from 0 to 3. Each + string of leds are operated individually. Specify the + list of strings used by the device. Any combination of + led strings can be used. + for pm8941: Default values are [00 01]. + for pmi8998: Default values are [00 01 02 03]. + +- qcom,external-pfet + Usage: optional + Value type: <bool> + Definition: Specify if external PFET control for short circuit + protection is used. This property is supported only + for PMI8998. + +- qcom,auto-string-detection + Usage: optional + Value type: <bool> + Definition: Enables auto-detection of the WLED string configuration. + This feature is not supported for PM8941. + Example: @@ -99,4 +152,21 @@ pm8941-wled@d800 { qcom,switching-freq = <1600>; qcom,ovp = <29>; qcom,num-strings = <2>; + qcom,enabled-strings = <0x00 0x01>; +}; + +pmi8998-wled@d800 { + compatible = "qcom,pmi8998-wled"; + reg = <0xd800 0xd900>; + label = "backlight"; + + interrupts = <3 0xd8 2 IRQ_TYPE_EDGE_RISING>, + <3 0xd8 1 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "short", "ovp"; + qcom,current-limit-microamp = <25000>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp-millivolt = <29600>; + qcom,num-strings = <4>; + qcom,enabled-strings = <0x00 0x01 0x02 0x03>; };
Update the bindings with the new properties used for PMI8998. Signed-off-by: Kiran Gunda <kgunda@codeaurora.org> --- .../bindings/leds/backlight/qcom-wled.txt | 84 ++++++++++++++++++++-- 1 file changed, 77 insertions(+), 7 deletions(-)