diff mbox series

[v5,1/2] drm/panel: Add support for Truly NT35597 panel

Message ID 1533265776-14326-1-git-send-email-abhinavk@codeaurora.org (mailing list archive)
State Not Applicable, archived
Delegated to: Andy Gross
Headers show
Series [v5,1/2] drm/panel: Add support for Truly NT35597 panel | expand

Commit Message

Abhinav Kumar Aug. 3, 2018, 3:09 a.m. UTC
From: "abhinavk@codeaurora.org" <abhinavk@codeaurora.org>

Add support for Truly NT35597 panel used
in MSM reference platforms.

This panel supports both single DSI and dual DSI
modes.

However, this patch series adds support only for
dual DSI mode.

Changes in v5:
- Added comments for the delays
- Fix error messages and return code
- Start using backlight_enable/disable helpers
- Start using ARRAY_SIZE everywhere
- Split the panel commands into three sets to
  remove redundant structure fields and simplify
  the DCS command sending method
- Use of_get_drm_display_mode() and simplify
  get_modes function
- Remove truly_wqxga_panel_del and do necessary
  cleanup
- Replace dev_err with DRM_DEV_ERROR

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
---
 drivers/gpu/drm/panel/Kconfig               |   8 +
 drivers/gpu/drm/panel/Makefile              |   1 +
 drivers/gpu/drm/panel/panel-truly-nt35597.c | 684 ++++++++++++++++++++++++++++
 3 files changed, 693 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c

Comments

kernel test robot Aug. 3, 2018, 4:47 p.m. UTC | #1
Hi abhinavk,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on linus/master]
[also build test WARNING on v4.18-rc7 next-20180802]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url:    https://github.com/0day-ci/linux/commits/Abhinav-Kumar/drm-panel-Add-support-for-Truly-NT35597-panel/20180803-114716
reproduce:
        # apt-get install sparse
        make ARCH=x86_64 allmodconfig
        make C=1 CF=-D__CHECK_ENDIAN__


sparse warnings: (new ones prefixed by >>)

>> drivers/gpu/drm/panel/panel-truly-nt35597.c:68:16: sparse: symbol 'panel_cmds_set_1' was not declared. Should it be static?
>> drivers/gpu/drm/panel/panel-truly-nt35597.c:207:16: sparse: symbol 'panel_cmds_set_2' was not declared. Should it be static?
>> drivers/gpu/drm/panel/panel-truly-nt35597.c:212:16: sparse: symbol 'panel_cmds_set_3' was not declared. Should it be static?

Please review and possibly fold the followup patch.

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox series

Patch

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 6020c30..7ae74c2 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -186,4 +186,12 @@  config DRM_PANEL_SITRONIX_ST7789V
 	  Say Y here if you want to enable support for the Sitronix
 	  ST7789V controller for 240x320 LCD panels
 
+config DRM_PANEL_TRULY_NT35597_WQXGA
+	tristate "Truly WQXGA"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	select VIDEOMODE_HELPERS
+	help
+	  Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
+	  Video Mode panel
 endmenu
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 5ccaaa9..80fd19f 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -19,3 +19,4 @@  obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
 obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
+obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
diff --git a/drivers/gpu/drm/panel/panel-truly-nt35597.c b/drivers/gpu/drm/panel/panel-truly-nt35597.c
new file mode 100644
index 0000000..e6c7662
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-truly-nt35597.c
@@ -0,0 +1,684 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <linux/pinctrl/consumer.h>
+
+#include <video/mipi_display.h>
+#include <video/of_videomode.h>
+#include <video/videomode.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_mipi_dsi.h>
+
+static const char * const regulator_names[] = {
+	"vdda",
+	"vdispp",
+	"vdispn",
+};
+
+static unsigned long const regulator_enable_loads[] = {
+	62000,
+	100000,
+	100000,
+};
+
+static unsigned long const regulator_disable_loads[] = {
+	80,
+	100,
+	100,
+};
+
+struct truly_wqxga {
+	struct device *dev;
+	struct drm_panel panel;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *mode_gpio;
+
+	struct backlight_device *backlight;
+	struct drm_display_mode dm;
+	u32 bus_flags;
+	struct mipi_dsi_device *dsi[2];
+
+	bool prepared;
+	bool enabled;
+};
+
+static inline struct truly_wqxga *panel_to_truly_wqxga(struct drm_panel *panel)
+{
+	return container_of(panel, struct truly_wqxga, panel);
+}
+
+#define MAX_LEN	5
+#define SHORT_PACKET 2
+#define LONG_PACKET 4
+
+struct cmd_set {
+	u8 commands[MAX_LEN];
+};
+
+struct cmd_set panel_cmds_set_1[] = {
+	/* CMD2_P0 */
+	{ { 0xff, 0x20 } },
+	{ { 0xfb, 0x01 } },
+	{ { 0x00, 0x01 } },
+	{ { 0x01, 0x55 } },
+	{ { 0x02, 0x45 } },
+	{ { 0x05, 0x40 } },
+	{ { 0x06, 0x19 } },
+	{ { 0x07, 0x1e } },
+	{ { 0x0b, 0x73 } },
+	{ { 0x0c, 0x73 } },
+	{ { 0x0e, 0xb0 } },
+	{ { 0x0f, 0xae } },
+	{ { 0x11, 0xb8 } },
+	{ { 0x13, 0x00 } },
+	{ { 0x58, 0x80 } },
+	{ { 0x59, 0x01 } },
+	{ { 0x5a, 0x00 } },
+	{ { 0x5b, 0x01 } },
+	{ { 0x5c, 0x80 } },
+	{ { 0x5d, 0x81 } },
+	{ { 0x5e, 0x00 } },
+	{ { 0x5f, 0x01 } },
+	{ { 0x72, 0x11 } },
+	{ { 0x68, 0x03 } },
+	/* CMD2_P4 */
+	{ { 0xFF, 0x24 } },
+	{ { 0xFB, 0x01 } },
+	{ { 0x00, 0x1C } },
+	{ { 0x01, 0x0B } },
+	{ { 0x02, 0x0C } },
+	{ { 0x03, 0x01 } },
+	{ { 0x04, 0x0F } },
+	{ { 0x05, 0x10 } },
+	{ { 0x06, 0x10 } },
+	{ { 0x07, 0x10 } },
+	{ { 0x08, 0x89 } },
+	{ { 0x09, 0x8A } },
+	{ { 0x0A, 0x13 } },
+	{ { 0x0B, 0x13 } },
+	{ { 0x0C, 0x15 } },
+	{ { 0x0D, 0x15 } },
+	{ { 0x0E, 0x17 } },
+	{ { 0x0F, 0x17 } },
+	{ { 0x10, 0x1C } },
+	{ { 0x11, 0x0B } },
+	{ { 0x12, 0x0C } },
+	{ { 0x13, 0x01 } },
+	{ { 0x14, 0x0F } },
+	{ { 0x15, 0x10 } },
+	{ { 0x16, 0x10 } },
+	{ { 0x17, 0x10 } },
+	{ { 0x18, 0x89 } },
+	{ { 0x19, 0x8A } },
+	{ { 0x1A, 0x13 } },
+	{ { 0x1B, 0x13 } },
+	{ { 0x1C, 0x15 } },
+	{ { 0x1D, 0x15 } },
+	{ { 0x1E, 0x17 } },
+	{ { 0x1F, 0x17 } },
+	/* STV */
+	{ { 0x20, 0x40 } },
+	{ { 0x21, 0x01 } },
+	{ { 0x22, 0x00 } },
+	{ { 0x23, 0x40 } },
+	{ { 0x24, 0x40 } },
+	{ { 0x25, 0x6D } },
+	{ { 0x26, 0x40 } },
+	{ { 0x27, 0x40 } },
+	/* Vend */
+	{ { 0xE0, 0x00 } },
+	{ { 0xDC, 0x21 } },
+	{ { 0xDD, 0x22 } },
+	{ { 0xDE, 0x07 } },
+	{ { 0xDF, 0x07 } },
+	{ { 0xE3, 0x6D } },
+	{ { 0xE1, 0x07 } },
+	{ { 0xE2, 0x07 } },
+	/* UD */
+	{ { 0x29, 0xD8 } },
+	{ { 0x2A, 0x2A } },
+	/* CLK */
+	{ { 0x4B, 0x03 } },
+	{ { 0x4C, 0x11 } },
+	{ { 0x4D, 0x10 } },
+	{ { 0x4E, 0x01 } },
+	{ { 0x4F, 0x01 } },
+	{ { 0x50, 0x10 } },
+	{ { 0x51, 0x00 } },
+	{ { 0x52, 0x80 } },
+	{ { 0x53, 0x00 } },
+	{ { 0x56, 0x00 } },
+	{ { 0x54, 0x07 } },
+	{ { 0x58, 0x07 } },
+	{ { 0x55, 0x25 } },
+	/* Reset XDONB */
+	{ { 0x5B, 0x43 } },
+	{ { 0x5C, 0x00 } },
+	{ { 0x5F, 0x73 } },
+	{ { 0x60, 0x73 } },
+	{ { 0x63, 0x22 } },
+	{ { 0x64, 0x00 } },
+	{ { 0x67, 0x08 } },
+	{ { 0x68, 0x04 } },
+	/* Resolution:1440x2560 */
+	{ { 0x72, 0x02 } },
+	/* mux */
+	{ { 0x7A, 0x80 } },
+	{ { 0x7B, 0x91 } },
+	{ { 0x7C, 0xD8 } },
+	{ { 0x7D, 0x60 } },
+	{ { 0x7F, 0x15 } },
+	{ { 0x75, 0x15 } },
+	/* ABOFF */
+	{ { 0xB3, 0xC0 } },
+	{ { 0xB4, 0x00 } },
+	{ { 0xB5, 0x00 } },
+	/* Source EQ */
+	{ { 0x78, 0x00 } },
+	{ { 0x79, 0x00 } },
+	{ { 0x80, 0x00 } },
+	{ { 0x83, 0x00 } },
+	/* FP BP */
+	{ { 0x93, 0x0A } },
+	{ { 0x94, 0x0A } },
+	/* Inversion Type */
+	{ { 0x8A, 0x00 } },
+	{ { 0x9B, 0xFF } },
+	/* IMGSWAP =1 @PortSwap=1 */
+	{ { 0x9D, 0xB0 } },
+	{ { 0x9F, 0x63 } },
+	{ { 0x98, 0x10 } },
+	/* FRM */
+	{ { 0xEC, 0x00 } },
+	/* CMD1 */
+	{ { 0xFF, 0x10 } },
+};
+
+struct cmd_set panel_cmds_set_2[] = {
+	/* VBP+VSA=,VFP = 10H */
+	{ { 0x3B, 0x03, 0x0A, 0x0A } },
+};
+
+struct cmd_set panel_cmds_set_3[] = {
+	/* FTE on */
+	{ { 0x35, 0x00 } },
+	/* EN_BK =1(auto black) */
+	{ { 0xE5, 0x01 } },
+	/* CMD mode(10) VDO mode(03) */
+	{ { 0xBB, 0x03 } },
+	/* Non Reload MTP */
+	{ { 0xFB, 0x01 } },
+};
+
+static int truly_dcs_write(struct drm_panel *panel, u32 command)
+{
+	struct truly_wqxga *ctx = panel_to_truly_wqxga(panel);
+	int i, ret;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write(ctx->dsi[i],
+			command, NULL, 0);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"set_display_off cmd failed for dsi = %d\n",
+			i);
+		}
+	}
+
+	return ret;
+}
+
+static int truly_dcs_write_buf(struct drm_panel *panel,
+	u32 size, u32 num_cmds, struct cmd_set *buf)
+{
+	struct truly_wqxga *ctx = panel_to_truly_wqxga(panel);
+	int ret = 0;
+	int i, j;
+
+	for (i = 0; i < num_cmds; i++) {
+		for (j = 0; j < ARRAY_SIZE(ctx->dsi); j++) {
+			ret = mipi_dsi_dcs_write_buffer(ctx->dsi[j],
+					buf[i].commands,
+					size);
+			if (ret < 0) {
+				DRM_DEV_ERROR(ctx->dev,
+					"failed to tx cmd [%d], err: %d\n",
+					i, ret);
+				return ret;
+			}
+		}
+	}
+
+	return ret;
+}
+
+#define truly_call_write_func(ret, func, panel, command) {\
+	ret = func(panel, command);     \
+}
+
+#define truly_write_buf_func(ret, func, panel, size, cmds, buf) {\
+	ret = func(panel, size, cmds, buf); \
+}
+
+static int truly_wqxga_power_on(struct truly_wqxga *ctx)
+{
+	int ret, i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+					regulator_enable_loads[i]);
+		if (ret)
+			return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	/* Reset sequence of truly panel requires
+	 * the reset pin to be pulled high for 10ms
+	 * followed by a low period of 10ms and then
+	 * pulled high again
+	 */
+
+	gpiod_set_value(ctx->reset_gpio, 1);
+	msleep(20);
+	gpiod_set_value(ctx->reset_gpio, 0);
+	msleep(20);
+	gpiod_set_value(ctx->reset_gpio, 1);
+
+	return 0;
+}
+
+static int truly_wqxga_power_off(struct truly_wqxga *ctx)
+{
+	int ret, i;
+
+	gpiod_set_value(ctx->reset_gpio, 0);
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+				regulator_disable_loads[i]);
+		if (ret)
+			return ret;
+	}
+
+	return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+}
+
+static int truly_wqxga_disable(struct drm_panel *panel)
+{
+	struct truly_wqxga *ctx = panel_to_truly_wqxga(panel);
+	int ret;
+
+	if (!ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_disable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
+				ret);
+	}
+
+	ctx->enabled = false;
+	return 0;
+}
+
+static int truly_wqxga_unprepare(struct drm_panel *panel)
+{
+	struct truly_wqxga *ctx = panel_to_truly_wqxga(panel);
+	int ret = 0;
+
+	if (!ctx->prepared)
+		return 0;
+
+	ctx->dsi[0]->mode_flags = 0;
+	ctx->dsi[1]->mode_flags = 0;
+
+	truly_call_write_func(ret, truly_dcs_write, panel,
+		MIPI_DCS_SET_DISPLAY_OFF);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_off cmd failed ret = %d\n",
+			ret);
+	}
+
+	/* 120ms delay required here as per DCS spec */
+	msleep(120);
+
+	truly_call_write_func(ret, truly_dcs_write, panel,
+		MIPI_DCS_ENTER_SLEEP_MODE);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"enter_sleep cmd failed ret = %d\n",
+			ret);
+	}
+
+	ret = truly_wqxga_power_off(ctx);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev,
+			"truly_wqxga_power_off failed ret = %d\n",
+			ret);
+
+	ctx->prepared = false;
+	return ret;
+}
+
+static int truly_wqxga_prepare(struct drm_panel *panel)
+{
+	struct truly_wqxga *ctx = panel_to_truly_wqxga(panel);
+	int ret;
+
+	if (ctx->prepared)
+		return 0;
+
+	ret = truly_wqxga_power_on(ctx);
+	if (ret < 0)
+		return ret;
+
+	ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM;
+	ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	truly_write_buf_func(ret, truly_dcs_write_buf,
+		panel, SHORT_PACKET,
+		ARRAY_SIZE(panel_cmds_set_1),
+		panel_cmds_set_1);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"panel_cmds_set_1 failed ret = %d\n",
+			ret);
+	}
+
+	truly_write_buf_func(ret, truly_dcs_write_buf,
+		panel, LONG_PACKET,
+		ARRAY_SIZE(panel_cmds_set_2),
+		panel_cmds_set_2);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"panel_cmds_set_2 failed ret = %d\n",
+			ret);
+	}
+
+	truly_write_buf_func(ret, truly_dcs_write_buf,
+		panel, SHORT_PACKET,
+		ARRAY_SIZE(panel_cmds_set_3),
+		panel_cmds_set_3);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"panel_cmds_set_3 failed ret = %d\n",
+			ret);
+	}
+
+	/* As per DSI spec need to wait for 120ms
+	 * after sending the exit sleep DCS command
+	 */
+
+	truly_call_write_func(ret, truly_dcs_write, panel,
+		MIPI_DCS_EXIT_SLEEP_MODE);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"exit_sleep_mode cmd failed ret = %d\n",
+			ret);
+	}
+
+	msleep(120);
+
+	truly_call_write_func(ret, truly_dcs_write, panel,
+		MIPI_DCS_SET_DISPLAY_ON);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_on cmd failed ret = %d\n",
+			ret);
+	}
+
+	/* Adding 120ms delay before the start of
+	 * pixel stream to the panel after sending
+	 * the set_display_on DCS command
+	 */
+
+	msleep(120);
+
+	ctx->prepared = true;
+
+	return 0;
+}
+
+static int truly_wqxga_enable(struct drm_panel *panel)
+{
+	struct truly_wqxga *ctx = panel_to_truly_wqxga(panel);
+	int ret;
+
+	if (ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_enable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
+						  ret);
+	}
+
+	ctx->enabled = true;
+
+	return 0;
+}
+
+static int truly_wqxga_get_modes(struct drm_panel *panel)
+{
+	struct drm_connector *connector = panel->connector;
+	struct truly_wqxga *ctx = panel_to_truly_wqxga(panel);
+	struct drm_display_mode *mode;
+
+	mode = drm_mode_create(connector->dev);
+	if (!mode) {
+		DRM_DEV_ERROR(ctx->dev,
+			"failed to create a new display mode\n");
+		return 0;
+	}
+
+	connector->display_info.width_mm = 74;
+	connector->display_info.height_mm = 131;
+	/* Copy the mode from the DT and add it */
+	drm_mode_copy(mode, &ctx->dm);
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs truly_wqxga_drm_funcs = {
+	.disable = truly_wqxga_disable,
+	.unprepare = truly_wqxga_unprepare,
+	.prepare = truly_wqxga_prepare,
+	.enable = truly_wqxga_enable,
+	.get_modes = truly_wqxga_get_modes,
+};
+
+static int truly_wqxga_panel_add(struct truly_wqxga *ctx)
+{
+	struct device *dev = ctx->dev;
+	int ret, i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
+		ctx->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+				      ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(ctx->reset_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
+			PTR_ERR(ctx->reset_gpio));
+		return PTR_ERR(ctx->reset_gpio);
+	}
+
+	ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->mode_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n",
+			PTR_ERR(ctx->mode_gpio));
+		return PTR_ERR(ctx->mode_gpio);
+	}
+
+	/* dual port */
+	gpiod_set_value(ctx->mode_gpio, 0);
+
+	ret = of_get_drm_display_mode(dev->of_node,
+		&ctx->dm, &ctx->bus_flags, 0);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "failed to get display mode\n");
+		return ret;
+	}
+
+	drm_panel_init(&ctx->panel);
+	ctx->panel.dev = dev;
+	ctx->panel.funcs = &truly_wqxga_drm_funcs;
+	drm_panel_add(&ctx->panel);
+
+	return 0;
+}
+
+static int truly_wqxga_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct truly_wqxga *ctx;
+	struct mipi_dsi_device *dsi1_device;
+	struct device_node *dsi1;
+	struct mipi_dsi_host *dsi1_host;
+	struct mipi_dsi_device *dsi_dev;
+	int ret = 0;
+	int i;
+
+	const struct mipi_dsi_device_info info = {.type = "trulynt35597",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+
+	if (!ctx)
+		return -ENOMEM;
+
+	/* This device represents itself as one with
+	 * two input ports which are fed by the output
+	 * ports of the two DSI controllers . The DSI0
+	 * is the master controller and has most of the
+	 * panel related info in its child node.
+	 */
+
+	dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
+	if (!dsi1) {
+		DRM_DEV_ERROR(dev,
+			"failed to get remote node for dsi1_device\n");
+		ret = -ENODEV;
+		goto err_get_remote;
+	}
+
+	dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);
+	if (!dsi1_host) {
+		DRM_DEV_ERROR(dev, "failed to find dsi host\n");
+		ret = -EPROBE_DEFER;
+		goto err_host;
+	}
+
+	of_node_put(dsi1);
+
+	/* register the second DSI device */
+	dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info);
+	if (IS_ERR(dsi1_device)) {
+		DRM_DEV_ERROR(dev, "failed to create dsi device\n");
+		ret = PTR_ERR(dsi);
+		goto err_dsi_device;
+	}
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	ctx->dev = dev;
+	ctx->dsi[0] = dsi;
+	ctx->dsi[1] = dsi1_device;
+
+	ret = truly_wqxga_panel_add(ctx);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to add panel\n");
+		goto err_panel_add;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		dsi_dev = ctx->dsi[i];
+		dsi_dev->lanes = 4;
+		dsi_dev->format = MIPI_DSI_FMT_RGB888;
+		dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
+			MIPI_DSI_CLOCK_NON_CONTINUOUS;
+		ret = mipi_dsi_attach(dsi_dev);
+		if (ret < 0) {
+			DRM_DEV_ERROR(dev,
+				"dsi attach failed i = %d\n", i);
+				goto err_dsi_attach;
+		}
+	}
+
+	return 0;
+
+err_dsi_attach:
+	drm_panel_remove(&ctx->panel);
+err_panel_add:
+	mipi_dsi_device_unregister(dsi1_device);
+err_dsi_device:
+err_host:
+	of_node_put(dsi1);
+err_get_remote:
+	return ret;
+}
+
+static int truly_wqxga_remove(struct mipi_dsi_device *dsi)
+{
+	struct truly_wqxga *ctx = mipi_dsi_get_drvdata(dsi);
+
+	if (ctx->dsi[0])
+		mipi_dsi_detach(ctx->dsi[0]);
+	if (ctx->dsi[1]) {
+		mipi_dsi_detach(ctx->dsi[1]);
+		mipi_dsi_device_unregister(ctx->dsi[1]);
+	}
+
+	drm_panel_remove(&ctx->panel);
+	return 0;
+}
+
+static const struct of_device_id truly_wqxga_of_match[] = {
+	{ .compatible = "truly,nt35597", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, truly_wqxga_of_match);
+
+static struct mipi_dsi_driver truly_wqxga_driver = {
+	.driver = {
+		.name = "panel_truly_nt35597",
+		.of_match_table = truly_wqxga_of_match,
+	},
+	.probe = truly_wqxga_probe,
+	.remove = truly_wqxga_remove,
+};
+module_mipi_dsi_driver(truly_wqxga_driver);
+
+MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver");
+MODULE_LICENSE("GPL v2");