| Message ID | 1577421760-1174-4-git-send-email-tdas@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add modem Clock controller (MSS CC) driver for SC7180 | expand |
Hey Taniya, On 2019-12-27 10:12, Taniya Das wrote: > Add support for the modem clock controller found on SC7180 > based devices. This would allow modem drivers to probe and > control their clocks. > > Signed-off-by: Taniya Das <tdas@codeaurora.org> > --- > drivers/clk/qcom/Kconfig | 9 +++++ > drivers/clk/qcom/Makefile | 1 + > drivers/clk/qcom/gcc-sc7180.c | 70 ++++++++++++++++++++++++++++++++ > drivers/clk/qcom/mss-sc7180.c | 94 > +++++++++++++++++++++++++++++++++++++++++++ > 4 files changed, 174 insertions(+) > create mode 100644 drivers/clk/qcom/mss-sc7180.c > > diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig > index 3b33ef1..5d4b6e5 100644 > --- a/drivers/clk/qcom/Kconfig > +++ b/drivers/clk/qcom/Kconfig > @@ -245,6 +245,15 @@ config SC_GCC_7180 > Say Y if you want to use peripheral devices such as UART, SPI, > I2C, USB, UFS, SDCC, etc. > > +config SC_MSS_7180 > + tristate "SC7180 MSS Clock Controller" > + select SC_GCC_7180 > + help > + Support for the MSS clock controller on Qualcomm Technologies, Inc > + SC7180 devices. > + Say Y if you want to use the MSS branch clocks of the MSS clock > + controller to reset the MSS subsystem. > + > config SDM_CAMCC_845 > tristate "SDM845 Camera Clock Controller" > select SDM_GCC_845 > diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile > index d899661..0e66bc6 100644 > --- a/drivers/clk/qcom/Makefile > +++ b/drivers/clk/qcom/Makefile > @@ -46,6 +46,7 @@ obj-$(CONFIG_QCS_GCC_404) += gcc-qcs404.o > obj-$(CONFIG_QCS_Q6SSTOP_404) += q6sstop-qcs404.o > obj-$(CONFIG_QCS_TURING_404) += turingcc-qcs404.o > obj-$(CONFIG_SC_GCC_7180) += gcc-sc7180.o > +obj-$(CONFIG_SC_MSS_7180) += mss-sc7180.o > obj-$(CONFIG_SDM_CAMCC_845) += camcc-sdm845.o > obj-$(CONFIG_SDM_DISPCC_845) += dispcc-sdm845.o > obj-$(CONFIG_SDM_GCC_660) += gcc-sdm660.o > diff --git a/drivers/clk/qcom/gcc-sc7180.c > b/drivers/clk/qcom/gcc-sc7180.c > index 38424e6..7b3a705 100644 > --- a/drivers/clk/qcom/gcc-sc7180.c > +++ b/drivers/clk/qcom/gcc-sc7180.c > @@ -2165,6 +2165,71 @@ static struct clk_branch gcc_video_xo_clk = { > }, > }; > > +static struct clk_branch gcc_mss_cfg_ahb_clk = { > + .halt_reg = 0x8a000, > + .halt_check = BRANCH_HALT, > + .clkr = { > + .enable_reg = 0x8a000, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "gcc_mss_cfg_ahb_clk", > + .ops = &clk_branch2_ops, > + }, > + }, > +}; > + > +static struct clk_branch gcc_mss_mfab_axis_clk = { > + .halt_reg = 0x8a004, > + .halt_check = BRANCH_HALT_VOTED, > + .clkr = { > + .enable_reg = 0x8a004, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "gcc_mss_mfab_axis_clk", > + .ops = &clk_branch2_ops, > + }, > + }, > +}; > + > +static struct clk_branch gcc_mss_nav_axi_clk = { > + .halt_reg = 0x8a00c, > + .halt_check = BRANCH_HALT_VOTED, > + .clkr = { > + .enable_reg = 0x8a00c, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "gcc_mss_nav_axi_clk", > + .ops = &clk_branch2_ops, > + }, > + }, > +}; > + > +static struct clk_branch gcc_mss_snoc_axi_clk = { > + .halt_reg = 0x8a150, > + .halt_check = BRANCH_HALT, > + .clkr = { > + .enable_reg = 0x8a150, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "gcc_mss_snoc_axi_clk", > + .ops = &clk_branch2_ops, > + }, > + }, > +}; > + > +static struct clk_branch gcc_mss_q6_memnoc_axi_clk = { > + .halt_reg = 0x8a154, > + .halt_check = BRANCH_HALT, > + .clkr = { > + .enable_reg = 0x8a154, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "gcc_mss_q6_memnoc_axi_clk", > + .ops = &clk_branch2_ops, > + }, > + }, > +}; > + > static struct gdsc ufs_phy_gdsc = { > .gdscr = 0x77004, > .pd = { > @@ -2334,6 +2399,11 @@ static struct clk_regmap *gcc_sc7180_clocks[] = > { > [GPLL7] = &gpll7.clkr, > [GPLL4] = &gpll4.clkr, > [GPLL1] = &gpll1.clkr, > + [GCC_MSS_CFG_AHB_CBCR] = &gcc_mss_cfg_ahb_clk.clkr, > + [GCC_MSS_MFAB_AXIS_CBCR] = &gcc_mss_mfab_axis_clk.clkr, > + [GCC_MSS_NAV_AXI_CBCR] = &gcc_mss_nav_axi_clk.clkr, > + [GCC_MSS_Q6_MEMNOC_AXI_CBCR] = &gcc_mss_q6_memnoc_axi_clk.clkr, > + [GCC_MSS_SNOC_AXI_CBCR] = &gcc_mss_snoc_axi_clk.clkr, > }; > > static const struct qcom_reset_map gcc_sc7180_resets[] = { > diff --git a/drivers/clk/qcom/mss-sc7180.c > b/drivers/clk/qcom/mss-sc7180.c > new file mode 100644 > index 0000000..24c38dc > --- /dev/null > +++ b/drivers/clk/qcom/mss-sc7180.c > @@ -0,0 +1,94 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Copyright (c) 2019, The Linux Foundation. All rights reserved. > + */ > + > +#include <linux/clk-provider.h> > +#include <linux/platform_device.h> > +#include <linux/module.h> > +#include <linux/of_address.h> > +#include <linux/regmap.h> > + > +#include <dt-bindings/clock/qcom,mss-sc7180.h> > + > +#include "clk-regmap.h" > +#include "clk-branch.h" > +#include "common.h" > + > +static struct clk_branch mss_axi_nav_clk = { > + .halt_reg = 0xbc, if we use the entire mpss_perph reg space it should be 0x20bc instead. > + .halt_check = BRANCH_HALT, > + .clkr = { > + .enable_reg = 0xbc, 0x20bc > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "mss_axi_nav_clk", > + .ops = &clk_branch2_ops, > + }, > + }, > +}; > + > +static struct clk_branch mss_axi_crypto_clk = { > + .halt_reg = 0xcc, if we use the entire mpss_perph reg space it should be 0x20cc instead. > + .halt_check = BRANCH_HALT, > + .clkr = { > + .enable_reg = 0xcc, 0x20cc > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "mss_axi_crypto_clk", > + .ops = &clk_branch2_ops, > + }, > + }, > +}; > + > +static struct regmap_config mss_regmap_config = { > + .reg_bits = 32, > + .reg_stride = 4, > + .val_bits = 32, > + .fast_io = true, > +}; > + > +static struct clk_regmap *mss_sc7180_clocks[] = { > + [MSS_AXI_CRYPTO_CLK] = &mss_axi_crypto_clk.clkr, > + [MSS_AXI_NAV_CLK] = &mss_axi_nav_clk.clkr, > +}; > + > +static const struct qcom_cc_desc mss_sc7180_desc = { > + .config = &mss_regmap_config, > + .clks = mss_sc7180_clocks, > + .num_clks = ARRAY_SIZE(mss_sc7180_clocks), > +}; > + > +static int mss_sc7180_probe(struct platform_device *pdev) > +{ > + return qcom_cc_probe(pdev, &mss_sc7180_desc); Similar to turingcc-qcs404 and q6sstop-qcs404 shouldn't we model the iface clk dependency here since both the above clocks cant be turned on/off without it. > +} > + > +static const struct of_device_id mss_sc7180_match_table[] = { > + { .compatible = "qcom,sc7180-mss" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, mss_sc7180_match_table); > + > +static struct platform_driver mss_sc7180_driver = { > + .probe = mss_sc7180_probe, > + .driver = { > + .name = "sc7180-mss", > + .of_match_table = mss_sc7180_match_table, > + }, > +}; > + > +static int __init mss_sc7180_init(void) > +{ > + return platform_driver_register(&mss_sc7180_driver); > +} > +subsys_initcall(mss_sc7180_init); > + > +static void __exit mss_sc7180_exit(void) > +{ > + platform_driver_unregister(&mss_sc7180_driver); > +} > +module_exit(mss_sc7180_exit); > + > +MODULE_DESCRIPTION("QTI MSS SC7180 Driver"); > +MODULE_LICENSE("GPL v2"); > -- > Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc.is a > member > of the Code Aurora Forum, hosted by the Linux Foundation.
Hi Sibi, Thanks for your review. On 12/27/2019 12:50 PM, Sibi Sankar wrote: > Hey Taniya, > >> static const struct qcom_reset_map gcc_sc7180_resets[] = { >> diff --git a/drivers/clk/qcom/mss-sc7180.c >> b/drivers/clk/qcom/mss-sc7180.c >> new file mode 100644 >> index 0000000..24c38dc >> --- /dev/null >> +++ b/drivers/clk/qcom/mss-sc7180.c >> @@ -0,0 +1,94 @@ >> +// SPDX-License-Identifier: GPL-2.0-only >> +/* >> + * Copyright (c) 2019, The Linux Foundation. All rights reserved. >> + */ >> + >> +#include <linux/clk-provider.h> >> +#include <linux/platform_device.h> >> +#include <linux/module.h> >> +#include <linux/of_address.h> >> +#include <linux/regmap.h> >> + >> +#include <dt-bindings/clock/qcom,mss-sc7180.h> >> + >> +#include "clk-regmap.h" >> +#include "clk-branch.h" >> +#include "common.h" >> + >> +static struct clk_branch mss_axi_nav_clk = { >> + .halt_reg = 0xbc, > > if we use the entire mpss_perph > reg space it should be 0x20bc > instead. > >> + .halt_check = BRANCH_HALT, >> + .clkr = { >> + .enable_reg = 0xbc, > > 0x20bc > yes, will take care in the next patch. >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "mss_axi_nav_clk", >> + .ops = &clk_branch2_ops, >> + }, >> + }, >> +}; >> + >> +static struct clk_branch mss_axi_crypto_clk = { >> + .halt_reg = 0xcc, > > if we use the entire mpss_perph > reg space it should be 0x20cc > instead. > >> + .halt_check = BRANCH_HALT, >> + .clkr = { >> + .enable_reg = 0xcc, > > 0x20cc > same as above. >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "mss_axi_crypto_clk", >> + .ops = &clk_branch2_ops, >> + }, >> + }, >> +}; >> + >> +static struct regmap_config mss_regmap_config = { >> + .reg_bits = 32, >> + .reg_stride = 4, >> + .val_bits = 32, >> + .fast_io = true, >> +}; >> + >> +static struct clk_regmap *mss_sc7180_clocks[] = { >> + [MSS_AXI_CRYPTO_CLK] = &mss_axi_crypto_clk.clkr, >> + [MSS_AXI_NAV_CLK] = &mss_axi_nav_clk.clkr, >> +}; >> + >> +static const struct qcom_cc_desc mss_sc7180_desc = { >> + .config = &mss_regmap_config, >> + .clks = mss_sc7180_clocks, >> + .num_clks = ARRAY_SIZE(mss_sc7180_clocks), >> +}; >> + >> +static int mss_sc7180_probe(struct platform_device *pdev) >> +{ >> + return qcom_cc_probe(pdev, &mss_sc7180_desc); > > Similar to turingcc-qcs404 and q6sstop-qcs404 > shouldn't we model the iface clk dependency > here since both the above clocks cant be turned > on/off without it. > Could we skip and proceed with the above for now? >> +} >> + >> +static const struct of_device_id mss_sc7180_match_table[] = { >> + { .compatible = "qcom,sc7180-mss" }, >> + { } >> +}; >> +MODULE_DEVICE_TABLE(of, mss_sc7180_match_table); >> + >> +static struct platform_driver mss_sc7180_driver = { >> + .probe = mss_sc7180_probe, >> + .driver = { >> + .name = "sc7180-mss", >> + .of_match_table = mss_sc7180_match_table, >> + }, >> +}; >> + >> +static int __init mss_sc7180_init(void) >> +{ >> + return platform_driver_register(&mss_sc7180_driver); >> +} >> +subsys_initcall(mss_sc7180_init); >> + >> +static void __exit mss_sc7180_exit(void) >> +{ >> + platform_driver_unregister(&mss_sc7180_driver); >> +} >> +module_exit(mss_sc7180_exit); >> + >> +MODULE_DESCRIPTION("QTI MSS SC7180 Driver"); >> +MODULE_LICENSE("GPL v2"); >> -- >> Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc.is a member >> of the Code Aurora Forum, hosted by the Linux Foundation. >
Hi, On Thu, Dec 26, 2019 at 8:43 PM Taniya Das <tdas@codeaurora.org> wrote: > > Add support for the modem clock controller found on SC7180 > based devices. This would allow modem drivers to probe and > control their clocks. > > Signed-off-by: Taniya Das <tdas@codeaurora.org> > --- > drivers/clk/qcom/Kconfig | 9 +++++ > drivers/clk/qcom/Makefile | 1 + > drivers/clk/qcom/gcc-sc7180.c | 70 ++++++++++++++++++++++++++++++++ > drivers/clk/qcom/mss-sc7180.c | 94 +++++++++++++++++++++++++++++++++++++++++++ > 4 files changed, 174 insertions(+) > create mode 100644 drivers/clk/qcom/mss-sc7180.c > > diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig > index 3b33ef1..5d4b6e5 100644 > --- a/drivers/clk/qcom/Kconfig > +++ b/drivers/clk/qcom/Kconfig > @@ -245,6 +245,15 @@ config SC_GCC_7180 > Say Y if you want to use peripheral devices such as UART, SPI, > I2C, USB, UFS, SDCC, etc. > > +config SC_MSS_7180 > + tristate "SC7180 MSS Clock Controller" > + select SC_GCC_7180 > + help > + Support for the MSS clock controller on Qualcomm Technologies, Inc > + SC7180 devices. > + Say Y if you want to use the MSS branch clocks of the MSS clock > + controller to reset the MSS subsystem. I didn't review your whole patch, but I was skimming through things and trying to figure out what the heck a "MSS" clock was for a while before I finally thought to look at the commit message and figured out that it probably means "modem subsystem". I assume you're going to spin this patch somewhat soon. When you do, can you please expand the "MSS" acronym somewhere in your KConfig description? Thanks! -Doug
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig index 3b33ef1..5d4b6e5 100644 --- a/drivers/clk/qcom/Kconfig +++ b/drivers/clk/qcom/Kconfig @@ -245,6 +245,15 @@ config SC_GCC_7180 Say Y if you want to use peripheral devices such as UART, SPI, I2C, USB, UFS, SDCC, etc. +config SC_MSS_7180 + tristate "SC7180 MSS Clock Controller" + select SC_GCC_7180 + help + Support for the MSS clock controller on Qualcomm Technologies, Inc + SC7180 devices. + Say Y if you want to use the MSS branch clocks of the MSS clock + controller to reset the MSS subsystem. + config SDM_CAMCC_845 tristate "SDM845 Camera Clock Controller" select SDM_GCC_845 diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile index d899661..0e66bc6 100644 --- a/drivers/clk/qcom/Makefile +++ b/drivers/clk/qcom/Makefile @@ -46,6 +46,7 @@ obj-$(CONFIG_QCS_GCC_404) += gcc-qcs404.o obj-$(CONFIG_QCS_Q6SSTOP_404) += q6sstop-qcs404.o obj-$(CONFIG_QCS_TURING_404) += turingcc-qcs404.o obj-$(CONFIG_SC_GCC_7180) += gcc-sc7180.o +obj-$(CONFIG_SC_MSS_7180) += mss-sc7180.o obj-$(CONFIG_SDM_CAMCC_845) += camcc-sdm845.o obj-$(CONFIG_SDM_DISPCC_845) += dispcc-sdm845.o obj-$(CONFIG_SDM_GCC_660) += gcc-sdm660.o diff --git a/drivers/clk/qcom/gcc-sc7180.c b/drivers/clk/qcom/gcc-sc7180.c index 38424e6..7b3a705 100644 --- a/drivers/clk/qcom/gcc-sc7180.c +++ b/drivers/clk/qcom/gcc-sc7180.c @@ -2165,6 +2165,71 @@ static struct clk_branch gcc_video_xo_clk = { }, }; +static struct clk_branch gcc_mss_cfg_ahb_clk = { + .halt_reg = 0x8a000, + .halt_check = BRANCH_HALT, + .clkr = { + .enable_reg = 0x8a000, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "gcc_mss_cfg_ahb_clk", + .ops = &clk_branch2_ops, + }, + }, +}; + +static struct clk_branch gcc_mss_mfab_axis_clk = { + .halt_reg = 0x8a004, + .halt_check = BRANCH_HALT_VOTED, + .clkr = { + .enable_reg = 0x8a004, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "gcc_mss_mfab_axis_clk", + .ops = &clk_branch2_ops, + }, + }, +}; + +static struct clk_branch gcc_mss_nav_axi_clk = { + .halt_reg = 0x8a00c, + .halt_check = BRANCH_HALT_VOTED, + .clkr = { + .enable_reg = 0x8a00c, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "gcc_mss_nav_axi_clk", + .ops = &clk_branch2_ops, + }, + }, +}; + +static struct clk_branch gcc_mss_snoc_axi_clk = { + .halt_reg = 0x8a150, + .halt_check = BRANCH_HALT, + .clkr = { + .enable_reg = 0x8a150, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "gcc_mss_snoc_axi_clk", + .ops = &clk_branch2_ops, + }, + }, +}; + +static struct clk_branch gcc_mss_q6_memnoc_axi_clk = { + .halt_reg = 0x8a154, + .halt_check = BRANCH_HALT, + .clkr = { + .enable_reg = 0x8a154, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "gcc_mss_q6_memnoc_axi_clk", + .ops = &clk_branch2_ops, + }, + }, +}; + static struct gdsc ufs_phy_gdsc = { .gdscr = 0x77004, .pd = { @@ -2334,6 +2399,11 @@ static struct clk_regmap *gcc_sc7180_clocks[] = { [GPLL7] = &gpll7.clkr, [GPLL4] = &gpll4.clkr, [GPLL1] = &gpll1.clkr, + [GCC_MSS_CFG_AHB_CBCR] = &gcc_mss_cfg_ahb_clk.clkr, + [GCC_MSS_MFAB_AXIS_CBCR] = &gcc_mss_mfab_axis_clk.clkr, + [GCC_MSS_NAV_AXI_CBCR] = &gcc_mss_nav_axi_clk.clkr, + [GCC_MSS_Q6_MEMNOC_AXI_CBCR] = &gcc_mss_q6_memnoc_axi_clk.clkr, + [GCC_MSS_SNOC_AXI_CBCR] = &gcc_mss_snoc_axi_clk.clkr, }; static const struct qcom_reset_map gcc_sc7180_resets[] = { diff --git a/drivers/clk/qcom/mss-sc7180.c b/drivers/clk/qcom/mss-sc7180.c new file mode 100644 index 0000000..24c38dc --- /dev/null +++ b/drivers/clk/qcom/mss-sc7180.c @@ -0,0 +1,94 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2019, The Linux Foundation. All rights reserved. + */ + +#include <linux/clk-provider.h> +#include <linux/platform_device.h> +#include <linux/module.h> +#include <linux/of_address.h> +#include <linux/regmap.h> + +#include <dt-bindings/clock/qcom,mss-sc7180.h> + +#include "clk-regmap.h" +#include "clk-branch.h" +#include "common.h" + +static struct clk_branch mss_axi_nav_clk = { + .halt_reg = 0xbc, + .halt_check = BRANCH_HALT, + .clkr = { + .enable_reg = 0xbc, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "mss_axi_nav_clk", + .ops = &clk_branch2_ops, + }, + }, +}; + +static struct clk_branch mss_axi_crypto_clk = { + .halt_reg = 0xcc, + .halt_check = BRANCH_HALT, + .clkr = { + .enable_reg = 0xcc, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "mss_axi_crypto_clk", + .ops = &clk_branch2_ops, + }, + }, +}; + +static struct regmap_config mss_regmap_config = { + .reg_bits = 32, + .reg_stride = 4, + .val_bits = 32, + .fast_io = true, +}; + +static struct clk_regmap *mss_sc7180_clocks[] = { + [MSS_AXI_CRYPTO_CLK] = &mss_axi_crypto_clk.clkr, + [MSS_AXI_NAV_CLK] = &mss_axi_nav_clk.clkr, +}; + +static const struct qcom_cc_desc mss_sc7180_desc = { + .config = &mss_regmap_config, + .clks = mss_sc7180_clocks, + .num_clks = ARRAY_SIZE(mss_sc7180_clocks), +}; + +static int mss_sc7180_probe(struct platform_device *pdev) +{ + return qcom_cc_probe(pdev, &mss_sc7180_desc); +} + +static const struct of_device_id mss_sc7180_match_table[] = { + { .compatible = "qcom,sc7180-mss" }, + { } +}; +MODULE_DEVICE_TABLE(of, mss_sc7180_match_table); + +static struct platform_driver mss_sc7180_driver = { + .probe = mss_sc7180_probe, + .driver = { + .name = "sc7180-mss", + .of_match_table = mss_sc7180_match_table, + }, +}; + +static int __init mss_sc7180_init(void) +{ + return platform_driver_register(&mss_sc7180_driver); +} +subsys_initcall(mss_sc7180_init); + +static void __exit mss_sc7180_exit(void) +{ + platform_driver_unregister(&mss_sc7180_driver); +} +module_exit(mss_sc7180_exit); + +MODULE_DESCRIPTION("QTI MSS SC7180 Driver"); +MODULE_LICENSE("GPL v2");
Add support for the modem clock controller found on SC7180 based devices. This would allow modem drivers to probe and control their clocks. Signed-off-by: Taniya Das <tdas@codeaurora.org> --- drivers/clk/qcom/Kconfig | 9 +++++ drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/gcc-sc7180.c | 70 ++++++++++++++++++++++++++++++++ drivers/clk/qcom/mss-sc7180.c | 94 +++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 174 insertions(+) create mode 100644 drivers/clk/qcom/mss-sc7180.c -- Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc.is a member of the Code Aurora Forum, hosted by the Linux Foundation.