| Message ID | 1578658699-30458-6-git-send-email-sanm@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add QUSB2 PHY support for SC7180 | expand |
On Fri, Jan 10, 2020 at 05:48:19PM +0530, Sandeep Maheswaram wrote: > Overriding the QUSB2 V2 Phy tuning parameters for SC7180 SOC. This patch doesn't set the PHY tuning parameters for the SC7180 SoC, but for the IDP board, which is based on the SC7180. Please reflect this in the commit message (including subject) to avoid confusion. > Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org> > --- > arch/arm64/boot/dts/qcom/sc7180-idp.dts | 6 ++++-- > 1 file changed, 4 insertions(+), 2 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts > index 388f50a..826cf02 100644 > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts > @@ -276,9 +276,11 @@ > vdda-pll-supply = <&vreg_l11a_1p8>; > vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; > qcom,imp-res-offset-value = <8>; > - qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; > - qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; > + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; > qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; > + qcom,bias-ctrl-value = <0x22>; > + qcom,charge-ctrl-value = <3>; > + qcom,hsdisc-trim-value = <0>; > }; > > &usb_1_qmpphy { > -- > QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member > of Code Aurora Forum, hosted by The Linux Foundation >
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts index 388f50a..826cf02 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts @@ -276,9 +276,11 @@ vdda-pll-supply = <&vreg_l11a_1p8>; vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; qcom,imp-res-offset-value = <8>; - qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; - qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; + qcom,bias-ctrl-value = <0x22>; + qcom,charge-ctrl-value = <3>; + qcom,hsdisc-trim-value = <0>; }; &usb_1_qmpphy {
Overriding the QUSB2 V2 Phy tuning parameters for SC7180 SOC. Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org> --- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)