| Message ID | 1590461850-9908-1-git-send-email-zijuhu@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v2] bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot | expand |
On Tue, May 26, 2020 at 10:57:30AM +0800, Zijun Hu wrote: > Warm reboot can not restore qca6390 controller baudrate > to default due to lack of controllable BT_EN pin or power > supply, so fails to download firmware after warm reboot. > > Fixed by sending EDL_SOC_RESET VSC to reset controller > within added device shutdown implementation. > > Signed-off-by: Zijun Hu <zijuhu@codeaurora.org> > --- > drivers/bluetooth/hci_qca.c | 27 +++++++++++++++++++++++++++ > 1 file changed, 27 insertions(+) > > diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c > index e4a6823..b479e51 100644 > --- a/drivers/bluetooth/hci_qca.c > +++ b/drivers/bluetooth/hci_qca.c > @@ -1975,6 +1975,32 @@ static void qca_serdev_remove(struct serdev_device *serdev) > hci_uart_unregister_device(&qcadev->serdev_hu); > } > > +static void qca_serdev_shutdown(struct device *dev) > +{ > + int res; nit: 'ret' would be a more standard name > + int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS); > + struct serdev_device *serdev = to_serdev_device(dev); > + struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev); > + const u8 ibs_wake_cmd[] = { 0xFD }; > + const u8 edl_reset_soc_cmd[] = { 0x01, 0x00, 0xFC, 0x01, 0x05 }; > + > + if (qcadev->btsoc_type == QCA_QCA6390) { > + serdev_device_write_flush(serdev); > + res = serdev_device_write_buf(serdev, > + ibs_wake_cmd, sizeof(ibs_wake_cmd)); > + BT_DBG("%s: send ibs_wake_cmd res = %d", __func__, res); Why use BT_DBG regardless of the result, instead of using BT_ERR/WARN only in the failure case? And does it actually make sense to continue in case of an error? > + serdev_device_wait_until_sent(serdev, timeout); > + usleep_range(8000, 10000); > + > + serdev_device_write_flush(serdev); > + res = serdev_device_write_buf(serdev, > + edl_reset_soc_cmd, sizeof(edl_reset_soc_cmd)); > + BT_DBG("%s: send edl_reset_soc_cmd res = %d", __func__, res); ditto > + serdev_device_wait_until_sent(serdev, timeout); > + usleep_range(8000, 10000); > + } > +} > + > static int __maybe_unused qca_suspend(struct device *dev) > { > struct hci_dev *hdev = container_of(dev, struct hci_dev, dev); > @@ -2100,6 +2126,7 @@ static struct serdev_device_driver qca_serdev_driver = { > .name = "hci_uart_qca", > .of_match_table = of_match_ptr(qca_bluetooth_of_match), > .acpi_match_table = ACPI_PTR(qca_bluetooth_acpi_match), > + .shutdown = qca_serdev_shutdown, > .pm = &qca_pm_ops, > }, > }; > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project >
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c index e4a6823..b479e51 100644 --- a/drivers/bluetooth/hci_qca.c +++ b/drivers/bluetooth/hci_qca.c @@ -1975,6 +1975,32 @@ static void qca_serdev_remove(struct serdev_device *serdev) hci_uart_unregister_device(&qcadev->serdev_hu); } +static void qca_serdev_shutdown(struct device *dev) +{ + int res; + int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS); + struct serdev_device *serdev = to_serdev_device(dev); + struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev); + const u8 ibs_wake_cmd[] = { 0xFD }; + const u8 edl_reset_soc_cmd[] = { 0x01, 0x00, 0xFC, 0x01, 0x05 }; + + if (qcadev->btsoc_type == QCA_QCA6390) { + serdev_device_write_flush(serdev); + res = serdev_device_write_buf(serdev, + ibs_wake_cmd, sizeof(ibs_wake_cmd)); + BT_DBG("%s: send ibs_wake_cmd res = %d", __func__, res); + serdev_device_wait_until_sent(serdev, timeout); + usleep_range(8000, 10000); + + serdev_device_write_flush(serdev); + res = serdev_device_write_buf(serdev, + edl_reset_soc_cmd, sizeof(edl_reset_soc_cmd)); + BT_DBG("%s: send edl_reset_soc_cmd res = %d", __func__, res); + serdev_device_wait_until_sent(serdev, timeout); + usleep_range(8000, 10000); + } +} + static int __maybe_unused qca_suspend(struct device *dev) { struct hci_dev *hdev = container_of(dev, struct hci_dev, dev); @@ -2100,6 +2126,7 @@ static struct serdev_device_driver qca_serdev_driver = { .name = "hci_uart_qca", .of_match_table = of_match_ptr(qca_bluetooth_of_match), .acpi_match_table = ACPI_PTR(qca_bluetooth_acpi_match), + .shutdown = qca_serdev_shutdown, .pm = &qca_pm_ops, }, };
Warm reboot can not restore qca6390 controller baudrate to default due to lack of controllable BT_EN pin or power supply, so fails to download firmware after warm reboot. Fixed by sending EDL_SOC_RESET VSC to reset controller within added device shutdown implementation. Signed-off-by: Zijun Hu <zijuhu@codeaurora.org> --- drivers/bluetooth/hci_qca.c | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+)