new file mode 100644
@@ -0,0 +1,207 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dpu-sc7180.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DPU dt properties
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
+ sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
+ bindings of MDSS and DPU are mentioned for SC7180 target.
+
+properties:
+ compatible:
+ items:
+ - const: qcom,sc7180-mdss
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: mdss
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Display AHB clock from gcc
+ - description: Display AHB clock from dispcc
+ - description: Display core clock
+
+ clock-names:
+ items:
+ - const: iface
+ - const: ahb
+ - const: core
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 1
+
+ iommus:
+ items:
+ - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0
+
+ ranges: true
+
+ interconnects:
+ items:
+ - description: Interconnect path specifying the port ids for data bus
+
+ interconnect-names:
+ const: mdp0-mem
+
+patternProperties:
+ "^display-controller@[0-9a-f]+$":
+ type: object
+ description: Node containing the properties of DPU.
+
+ properties:
+ compatible:
+ items:
+ - const: qcom,sc7180-dpu
+
+ reg:
+ items:
+ - description: Address offset and size for mdp register set
+ - description: Address offset and size for vbif register set
+
+ reg-names:
+ items:
+ - const: mdp
+ - const: vbif
+
+ clocks:
+ items:
+ - description: Display hf axi clock
+ - description: Display ahb clock
+ - description: Display rotator clock
+ - description: Display lut clock
+ - description: Display core clock
+ - description: Display vsync clock
+
+ clock-names:
+ items:
+ - const: bus
+ - const: iface
+ - const: rot
+ - const: lut
+ - const: core
+ - const: vsync
+
+ interrupts:
+ maxItems: 1
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/port
+ type: object
+ description: |
+ Contains the list of output ports from DPU device. These ports
+ connect to interfaces that are external to the DPU hardware,
+ such as DSI, DP etc. Each output port contains an endpoint that
+ describes how it is connected to an external interface.
+
+ properties:
+ port@0:
+ type: object
+ description: DPU_INTF1 (DSI1)
+
+ port@1:
+ type: object
+ description: DPU_INTF2 (DSI2)
+ port@2:
+ type: object
+ description: DPU_INTF0 (DP)
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - power-domains
+ - clocks
+ - interrupts
+ - interrupt-controller
+ - iommus
+ - ranges
+
+additionalProperties: true
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
+ #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interconnect/qcom,sdm845.h>
+
+ mdss@ae00000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "qcom,sc7180-mdss";
+ reg = <0xae00000 0x1000>;
+ reg-names = "mdss";
+ power-domains = <&dispcc MDSS_GDSC>;
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "ahb", "core";
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interconnects = <&mmss_noc MASTER_MDP0 &mc_virt SLAVE_EBI1>;
+ interconnect-names = "mdp0-mem";
+
+ iommus = <&apps_smmu 0x800 0x2>;
+ ranges;
+
+ display-controller@ae01000 {
+ compatible = "qcom,sc7180-dpu";
+ reg = <0x0ae01000 0x8f000>,
+ <0x0aeb0000 0x2008>;
+
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_ROT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus", "iface", "rot", "lut", "core",
+ "vsync";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ dpu_intf0_out: endpoint {
+ remote-endpoint = <&dp_in>;
+ };
+ };
+ };
+ };
+ };
+...
new file mode 100644
@@ -0,0 +1,188 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/dpu-sdm845.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Description of Qualcomm Display DPU dt properties
+
+maintainers:
+ - Krishna Manikandan <mkrishn@codeaurora.org>
+
+description: |
+ Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
+ sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
+ bindings of MDSS and DPU are mentioned for SDM845 target.
+
+properties:
+ compatible:
+ items:
+ - const: qcom,sdm845-mdss
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ const: mdss
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Display AHB clock from gcc
+ - description: Display AXI clock
+ - description: Display core clock
+
+ clock-names:
+ items:
+ - const: iface
+ - const: bus
+ - const: core
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 1
+
+ iommus:
+ items:
+ - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0
+ - description: Phandle to apps_smmu node with SID mask for Hard-Fail port1
+
+ ranges: true
+
+patternProperties:
+ "^display-controller@[0-9a-f]+$":
+ type: object
+ description: Node containing the properties of DPU.
+
+ properties:
+ compatible:
+ items:
+ - const: qcom,sdm845-dpu
+
+ reg:
+ items:
+ - description: Address offset and size for mdp register set
+ - description: Address offset and size for vbif register set
+
+ reg-names:
+ items:
+ - const: mdp
+ - const: vbif
+
+ clocks:
+ items:
+ - description: Display ahb clock
+ - description: Display axi clock
+ - description: Display core clock
+ - description: Display vsync clock
+
+ clock-names:
+ items:
+ - const: iface
+ - const: bus
+ - const: core
+ - const: vsync
+
+ interrupts:
+ maxItems: 1
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/port
+ type: object
+ description: |
+ Contains the list of output ports from DPU device. These ports
+ connect to interfaces that are external to the DPU hardware,
+ such as DSI, DP etc. Each output port contains an endpoint that
+ describes how it is connected to an external interface.
+
+ properties:
+ port@0:
+ type: object
+ description: DPU_INTF1 (DSI1)
+
+ port@1:
+ type: object
+ description: DPU_INTF2 (DSI2)
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - power-domains
+ - clocks
+ - interrupts
+ - interrupt-controller
+ - iommus
+ - ranges
+
+additionalProperties: true
+
+examples:
+- |
+ #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ mdss@ae00000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "qcom,sdm845-mdss";
+ reg = <0x0ae00000 0x1000>;
+ reg-names = "mdss";
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&gcc GCC_DISP_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "bus", "core";
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_smmu 0x880 0x8>,
+ <&apps_smmu 0xc80 0x8>;
+ ranges;
+
+ display-controller@ae01000 {
+ compatible = "qcom,sdm845-dpu";
+ reg = <0x0ae01000 0x8f000>,
+ <0x0aeb0000 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "iface", "bus", "core", "vsync";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&dsi1_in>;
+ };
+ };
+ };
+ };
+ };
+...
deleted file mode 100644
@@ -1,141 +0,0 @@
-Qualcomm Technologies, Inc. DPU KMS
-
-Description:
-
-Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
-sub-blocks like DPU display controller, DSI and DP interfaces etc.
-The DPU display controller is found in SDM845 SoC.
-
-MDSS:
-Required properties:
-- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss"
-- reg: physical base address and length of contoller's registers.
-- reg-names: register region names. The following region is required:
- * "mdss"
-- power-domains: a power domain consumer specifier according to
- Documentation/devicetree/bindings/power/power_domain.txt
-- clocks: list of clock specifiers for clocks needed by the device.
-- clock-names: device clock names, must be in same order as clocks property.
- The following clocks are required:
- * "iface"
- * "bus"
- * "core"
-- interrupts: interrupt signal from MDSS.
-- interrupt-controller: identifies the node as an interrupt controller.
-- #interrupt-cells: specifies the number of cells needed to encode an interrupt
- source, should be 1.
-- iommus: phandle of iommu device node.
-- #address-cells: number of address cells for the MDSS children. Should be 1.
-- #size-cells: Should be 1.
-- ranges: parent bus address space is the same as the child bus address space.
-- interconnects : interconnect path specifier for MDSS according to
- Documentation/devicetree/bindings/interconnect/interconnect.txt. Should be
- 2 paths corresponding to 2 AXI ports.
-- interconnect-names : MDSS will have 2 port names to differentiate between the
- 2 interconnect paths defined with interconnect specifier.
-
-Optional properties:
-- assigned-clocks: list of clock specifiers for clocks needing rate assignment
-- assigned-clock-rates: list of clock frequencies sorted in the same order as
- the assigned-clocks property.
-
-MDP:
-Required properties:
-- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu"
-- reg: physical base address and length of controller's registers.
-- reg-names : register region names. The following region is required:
- * "mdp"
- * "vbif"
-- clocks: list of clock specifiers for clocks needed by the device.
-- clock-names: device clock names, must be in same order as clocks property.
- The following clocks are required.
- * "bus"
- * "iface"
- * "core"
- * "vsync"
-- interrupts: interrupt line from DPU to MDSS.
-- ports: contains the list of output ports from DPU device. These ports connect
- to interfaces that are external to the DPU hardware, such as DSI, DP etc.
-
- Each output port contains an endpoint that describes how it is connected to an
- external interface. These are described by the standard properties documented
- here:
- Documentation/devicetree/bindings/graph.txt
- Documentation/devicetree/bindings/media/video-interfaces.txt
-
- Port 0 -> DPU_INTF1 (DSI1)
- Port 1 -> DPU_INTF2 (DSI2)
-
-Optional properties:
-- assigned-clocks: list of clock specifiers for clocks needing rate assignment
-- assigned-clock-rates: list of clock frequencies sorted in the same order as
- the assigned-clocks property.
-
-Example:
-
- mdss: mdss@ae00000 {
- compatible = "qcom,sdm845-mdss";
- reg = <0xae00000 0x1000>;
- reg-names = "mdss";
-
- power-domains = <&clock_dispcc 0>;
-
- clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>,
- <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
- clock-names = "iface", "bus", "core";
-
- assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
- assigned-clock-rates = <300000000>;
-
- interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-controller;
- #interrupt-cells = <1>;
-
- interconnects = <&rsc_hlos MASTER_MDP0 &rsc_hlos SLAVE_EBI1>,
- <&rsc_hlos MASTER_MDP1 &rsc_hlos SLAVE_EBI1>;
-
- interconnect-names = "mdp0-mem", "mdp1-mem";
-
- iommus = <&apps_iommu 0>;
-
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0xae00000 0xb2008>;
-
- mdss_mdp: mdp@ae01000 {
- compatible = "qcom,sdm845-dpu";
- reg = <0 0x1000 0x8f000>, <0 0xb0000 0x2008>;
- reg-names = "mdp", "vbif";
-
- clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>,
- <&clock_dispcc DISP_CC_MDSS_AXI_CLK>,
- <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
- <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
- clock-names = "iface", "bus", "core", "vsync";
-
- assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
- <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
- assigned-clock-rates = <0 0 300000000 19200000>;
-
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- dpu_intf1_out: endpoint {
- remote-endpoint = <&dsi0_in>;
- };
- };
-
- port@1 {
- reg = <1>;
- dpu_intf2_out: endpoint {
- remote-endpoint = <&dsi1_in>;
- };
- };
- };
- };
- };
MSM Mobile Display Subsytem (MDSS) encapsulates sub-blocks like DPU display controller, DSI etc. Add YAML schema for DPU device tree bindings. Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org> Changes in v2: - Changed dpu to DPU (Sam Ravnborg) - Fixed indentation issues (Sam Ravnborg) - Added empty line between different properties (Sam Ravnborg) - Replaced reference txt files with their corresponding yaml files (Sam Ravnborg) - Modified the file to use "|" only when it is necessary (Sam Ravnborg) Changes in v3: - Corrected the license used (Rob Herring) - Added maxItems for properties (Rob Herring) - Dropped generic descriptions (Rob Herring) - Added ranges property (Rob Herring) - Corrected the indendation (Rob Herring) - Added additionalProperties (Rob Herring) - Split dsi file into two, one for dsi controller and another one for dsi phy per target (Rob Herring) - Corrected description for pinctrl-names (Rob Herring) - Corrected the examples used in yaml file (Rob Herring) - Delete dsi.txt and dpu.txt (Rob Herring) Changes in v4: - Move schema up by one level (Rob Herring) - Add patternProperties for mdp node (Rob Herring) - Corrected description of some properties (Rob Herring) Changes in v5: - Correct the indentation (Rob Herring) - Remove unnecessary description from properties (Rob Herring) - Correct the number of interconnect entries (Rob Herring) - Add interconnect names for sc7180 (Rob Herring) - Add description for ports (Rob Herring) - Remove common properties (Rob Herring) - Add unevalutatedProperties (Rob Herring) - Reference existing dsi controller yaml in the common dsi controller file (Rob Herring) - Correct the description of clock names to include only the clocks that are required (Rob Herring) - Remove properties which are already covered under the common binding (Rob Herring) - Add dsi phy supply nodes which are required for sc7180 and sdm845 targets (Rob Herring) - Add type ref for syscon-sfpb (Rob Herring) Changes in v6: - Fixed errors during dt_binding_check (Rob Herring) - Add maxItems for phys and phys-names (Rob Herring) - Use unevaluatedProperties wherever required (Rob Herring) - Removed interrupt controller from required properties for dsi controller (Rob Herring) - Add constraints for dsi-phy reg-names based on the compatible phy version (Rob Herring) - Add constraints for dsi-phy supply nodes based on the compatible phy version (Rob Herring) Changes in v7: - Add default value for qcom,mdss-mdp-transfer-time-us (Rob Herring) - Modify the schema for data-lanes (Rob Herring) - Split the phy schema into separate schemas based on the phy version (Rob Herring) Changes in v8: - Resolve merge conflicts with latest dsi.txt file - Include dp yaml change also in the same series Changes in v9: - Combine target specific dsi controller yaml files to a single yaml file (Rob Herring) - Combine target specific dsi phy yaml files into a single yaml file (Rob Herring) - Use unevaluatedProperties and additionalProperties wherever required - Remove duplicate properties from common yaml files Changes in v10: - Split the patch into separate patches for DPU, DSI and PHY (Stephen Boyd) - Drop unnecessary fullstop (Stephen Boyd) - Add newline whereever required (Stephen Boyd) - Add description for clock used (Stephen Boyd) - Modify the description for interconnect entries (Stephen Boyd) - Drop assigned clock entries as it a generic property (Stephen Boyd) - Correct the definition for interrupts (Stephen Boyd) - Drop clock names from required properties (Stephen Boyd) - Drop labels for display nodes from example (Stephen Boyd) - Drop flags from interrupts entries (Stephen Boyd) Changes in v11: - Drop maxItems for clocks (Stephen Boyd) Changes in v12: - Add description for register property (Stephen Boyd) - Add maxItems for interrupts (Stephen Boyd) - Add description for iommus property (Stephen Boyd) - Add description for interconnects (Stephen Boyd) - Change display node name to display_controller (Stephen Boyd) Changes in v13: - Add maxItems for reg property (Stephen Boyd) - Add ranges property in example (Stephen Boyd) - Modify description for iommus property (Stephen Boyd) - Add Dp bindings for ports in the same patch (Stephen Boyd) - Remove soc from examples and change address and size cells accordingly (Stephen Boyd) - Add reference for ports --- .../bindings/display/msm/dpu-sc7180.yaml | 207 +++++++++++++++++++++ .../bindings/display/msm/dpu-sdm845.yaml | 188 +++++++++++++++++++ .../devicetree/bindings/display/msm/dpu.txt | 141 -------------- 3 files changed, 395 insertions(+), 141 deletions(-) create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml delete mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt