| Message ID | 1622668118-2237-1-git-send-email-khsieh@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64/dts/qcom/sc7180: Add Display Port dt node | expand |
Subject should be "arm64: dts: qcom: sc7180: Add DisplayPort node" Quoting Kuogee Hsieh (2021-06-02 14:08:38) > Add DP device node on sc7180. > > Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> > --- > arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 9 ++++ > arch/arm64/boot/dts/qcom/sc7180.dtsi | 77 ++++++++++++++++++++++++++++ > 2 files changed, 86 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi > index 24d293e..53ef3961 100644 > --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi > @@ -786,6 +786,15 @@ hp_i2c: &i2c9 { > status = "okay"; > }; > > +&msm_dp { Maybe the lable should just be 'dp' as msm_ prefix is redundant. > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&dp_hot_plug_det>; > + data-lanes = <0 1>; > + vdda-1p2-supply = <&vdda_usb_ss_dp_1p2>; > + vdda-0p9-supply = <&vdda_usb_ss_dp_core>; > +}; > + > &pm6150_adc { > charger-thermistor@4f { > reg = <ADC5_AMUX_THM3_100K_PU>; > diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi > index 6228ba2..2e45098 100644 > --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi > @@ -3148,6 +3155,76 @@ > > status = "disabled"; > }; > + > + msm_dp: displayport-controller@ae90000 { > + status = "disabled"; Can this come after compatible? > + compatible = "qcom,sc7180-dp"; > + > + reg = <0 0x0ae90000 0 0x1400>; > + > + interrupt-parent = <&mdss>; > + interrupts = <12 IRQ_TYPE_NONE>; Should be interrupts = <12>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&dispcc DISP_CC_MDSS_DP_AUX_CLK>, > + <&dispcc DISP_CC_MDSS_DP_LINK_CLK>, > + <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>; > + clock-names = "core_iface", "core_aux", "ctrl_link", > + "ctrl_link_iface", "stream_pixel"; > + #clock-cells = <1>; > + assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>, > + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>; > + assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>; > + phys = <&dp_phy>; > + phy-names = "dp"; > + > + operating-points-v2 = <&dp_opp_table>; > + power-domains = <&rpmhpd SC7180_CX>; > + > + #sound-dai-cells = <0>; Move this next to phy? Or at least a newline here to split from ports. > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + port@0 { > + reg = <0>; > + dp_in: endpoint { > + remote-endpoint = <&dpu_intf0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dp_out: endpoint { }; > + }; > + }; > + > + dp_opp_table: dp-opp-table { Maybe node name should be opp-table? dp_opp_table: opp-table { }; > + compatible = "operating-points-v2"; > + > + opp-160000000 { > + opp-hz = /bits/ 64 <160000000>; > + required-opps = <&rpmhpd_opp_low_svs>;
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index 24d293e..53ef3961 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -786,6 +786,15 @@ hp_i2c: &i2c9 { status = "okay"; }; +&msm_dp { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hot_plug_det>; + data-lanes = <0 1>; + vdda-1p2-supply = <&vdda_usb_ss_dp_1p2>; + vdda-0p9-supply = <&vdda_usb_ss_dp_core>; +}; + &pm6150_adc { charger-thermistor@4f { reg = <ADC5_AMUX_THM3_100K_PU>; diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index 6228ba2..2e45098 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -3032,6 +3032,13 @@ remote-endpoint = <&dsi0_in>; }; }; + + port@2 { + reg = <2>; + dpu_intf0_out: endpoint { + remote-endpoint = <&dp_in>; + }; + }; }; mdp_opp_table: mdp-opp-table { @@ -3148,6 +3155,76 @@ status = "disabled"; }; + + msm_dp: displayport-controller@ae90000 { + status = "disabled"; + compatible = "qcom,sc7180-dp"; + + reg = <0 0x0ae90000 0 0x1400>; + + interrupt-parent = <&mdss>; + interrupts = <12 IRQ_TYPE_NONE>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_DP_AUX_CLK>, + <&dispcc DISP_CC_MDSS_DP_LINK_CLK>, + <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>, + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>; + clock-names = "core_iface", "core_aux", "ctrl_link", + "ctrl_link_iface", "stream_pixel"; + #clock-cells = <1>; + assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>, + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>; + assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>; + phys = <&dp_phy>; + phy-names = "dp"; + + operating-points-v2 = <&dp_opp_table>; + power-domains = <&rpmhpd SC7180_CX>; + + #sound-dai-cells = <0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + dp_in: endpoint { + remote-endpoint = <&dpu_intf0_out>; + }; + }; + + port@1 { + reg = <1>; + dp_out: endpoint { }; + }; + }; + + dp_opp_table: dp-opp-table { + compatible = "operating-points-v2"; + + opp-160000000 { + opp-hz = /bits/ 64 <160000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-270000000 { + opp-hz = /bits/ 64 <270000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-540000000 { + opp-hz = /bits/ 64 <540000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-810000000 { + opp-hz = /bits/ 64 <810000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + }; dispcc: clock-controller@af00000 {
Add DP device node on sc7180. Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> --- arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 9 ++++ arch/arm64/boot/dts/qcom/sc7180.dtsi | 77 ++++++++++++++++++++++++++++ 2 files changed, 86 insertions(+)