| Message ID | 1624377651-30604-5-git-send-email-pmaliset@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add DT bindings and DT nodes for PCIe and PHY in SC7280 | expand |
On 2021-06-22 21:30, Prasad Malisetty wrote: > pipe-clk mux needs to switch between pipe_clk > and XO as part of LPM squence. This is done by setting > pipe_clk mux as parent of pipe_clk after phy init. > This is a new requirement for sc7280. > For accessing to DBI registers during L23, > need to switch the pipe clock with free-running > clock (TCXO) using GCC’s registers > > Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org> > --- > drivers/pci/controller/dwc/pcie-qcom.c | 22 ++++++++++++++++++++++ > 1 file changed, 22 insertions(+) > > diff --git a/drivers/pci/controller/dwc/pcie-qcom.c > b/drivers/pci/controller/dwc/pcie-qcom.c > index 8a7a300..80e9ee4 100644 > --- a/drivers/pci/controller/dwc/pcie-qcom.c > +++ b/drivers/pci/controller/dwc/pcie-qcom.c > @@ -166,6 +166,9 @@ struct qcom_pcie_resources_2_7_0 { > struct regulator_bulk_data supplies[2]; > struct reset_control *pci_reset; > struct clk *pipe_clk; > + struct clk *pipe_clk_mux; > + struct clk *pipe_ext_src; > + struct clk *ref_clk_src; > }; > > union qcom_pcie_resources { > @@ -1167,6 +1170,20 @@ static int qcom_pcie_get_resources_2_7_0(struct > qcom_pcie *pcie) > if (ret < 0) > return ret; > > + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) { > + res->pipe_clk_mux = devm_clk_get(dev, "pipe_mux"); > + if (IS_ERR(res->pipe_clk_mux)) > + return PTR_ERR(res->pipe_clk_mux); > + > + res->pipe_ext_src = devm_clk_get(dev, "phy_pipe"); > + if (IS_ERR(res->pipe_ext_src)) > + return PTR_ERR(res->pipe_ext_src); > + > + res->ref_clk_src = devm_clk_get(dev, "ref"); > + if (IS_ERR(res->ref_clk_src)) > + return PTR_ERR(res->ref_clk_src); > + } > + > res->pipe_clk = devm_clk_get(dev, "pipe"); > return PTR_ERR_OR_ZERO(res->pipe_clk); > } > @@ -1255,6 +1272,11 @@ static void qcom_pcie_deinit_2_7_0(struct > qcom_pcie *pcie) > static int qcom_pcie_post_init_2_7_0(struct qcom_pcie *pcie) > { > struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; > + struct dw_pcie *pci = pcie->pci; > + struct device *dev = pci->dev; > + > + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) > + clk_set_parent(res->pipe_clk_mux, res->pipe_ext_src); > > return clk_prepare_enable(res->pipe_clk); > } Hi All, Greetings of the day !! Could you please provide your comments on updated change series Thanks -Prasad
On Tue 22 Jun 11:00 CDT 2021, Prasad Malisetty wrote: > pipe-clk mux needs to switch between pipe_clk If you spell "pipe-clk mux" as "gcc_pcie_N_pipe_clk_src" there's no ambiguity in which clock you refer to. > and XO as part of LPM squence. This is done by setting > pipe_clk mux as parent of pipe_clk after phy init. I thought the two possible cases where: xo -> gcc_pcie_N_pipe_clk_src -> gcc_pcie_N_pipe_clk PHY::pipe_clk -> gcc_pcie_N_pipe_clk_src -> gcc_pcie_N_pipe_clk But here you're saying that you're setting the parent of PHY::pipe_clk to gcc_pcie_N_pipe_clk? > This is a new requirement for sc7280. > For accessing to DBI registers during L23, > need to switch the pipe clock with free-running > clock (TCXO) using GCC’s registers So in previous platforms we could access DBI registers, in L23, without any clock? What happens if we use xo as parent for the pipe clock > > Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org> > --- > drivers/pci/controller/dwc/pcie-qcom.c | 22 ++++++++++++++++++++++ > 1 file changed, 22 insertions(+) > > diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c > index 8a7a300..80e9ee4 100644 > --- a/drivers/pci/controller/dwc/pcie-qcom.c > +++ b/drivers/pci/controller/dwc/pcie-qcom.c > @@ -166,6 +166,9 @@ struct qcom_pcie_resources_2_7_0 { > struct regulator_bulk_data supplies[2]; > struct reset_control *pci_reset; > struct clk *pipe_clk; > + struct clk *pipe_clk_mux; > + struct clk *pipe_ext_src; > + struct clk *ref_clk_src; > }; > > union qcom_pcie_resources { > @@ -1167,6 +1170,20 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie) > if (ret < 0) > return ret; > > + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) { So this is the first 2.7.0 that has this need? Are we just going to add more compatibles to this list going forward? > + res->pipe_clk_mux = devm_clk_get(dev, "pipe_mux"); > + if (IS_ERR(res->pipe_clk_mux)) > + return PTR_ERR(res->pipe_clk_mux); So this is gcc_pcie_N_pipe_clk_src? > + > + res->pipe_ext_src = devm_clk_get(dev, "phy_pipe"); > + if (IS_ERR(res->pipe_ext_src)) > + return PTR_ERR(res->pipe_ext_src); And this is the pipe_clk coming out of the PHY (What I call PHY::pipe_clk above)? > + > + res->ref_clk_src = devm_clk_get(dev, "ref"); > + if (IS_ERR(res->ref_clk_src)) > + return PTR_ERR(res->ref_clk_src); And this is TCXO? > + } > + > res->pipe_clk = devm_clk_get(dev, "pipe"); > return PTR_ERR_OR_ZERO(res->pipe_clk); > } > @@ -1255,6 +1272,11 @@ static void qcom_pcie_deinit_2_7_0(struct qcom_pcie *pcie) > static int qcom_pcie_post_init_2_7_0(struct qcom_pcie *pcie) > { > struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; > + struct dw_pcie *pci = pcie->pci; > + struct device *dev = pci->dev; > + > + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) > + clk_set_parent(res->pipe_clk_mux, res->pipe_ext_src); > So after phy_power_on() (not "phy init" as you say in the commit message, perhaps you don't mean phy_init() but in general terms "phy initialization") you need to make sure that gcc_pcie_N_pipe_clk_src is actually fed by PHY::pipe_clk? 1) What's the gcc_pcie_N_pipe_clk_src parent before this? 2) Will the PHY initialization really succeed if the pipe_clk feeding back from gcc isn't based on the PHY's pipe_clk? Is this a change in sc7280? 3) In the commit message you're talking about the need to make XO the parent of gcc_pcie_N_pipe_clk_src during L23, where in this patch does that happen? Regards, Bjorn > return clk_prepare_enable(res->pipe_clk); > } > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project >
On 2021-07-12 21:33, Bjorn Andersson wrote: > On Tue 22 Jun 11:00 CDT 2021, Prasad Malisetty wrote: > >> pipe-clk mux needs to switch between pipe_clk > > If you spell "pipe-clk mux" as "gcc_pcie_N_pipe_clk_src" there's no > ambiguity in which clock you refer to. > Sure, it looks fine, I will modify accordingly. >> and XO as part of LPM squence. This is done by setting >> pipe_clk mux as parent of pipe_clk after phy init. > > I thought the two possible cases where: > > xo -> gcc_pcie_N_pipe_clk_src -> gcc_pcie_N_pipe_clk > PHY::pipe_clk -> gcc_pcie_N_pipe_clk_src -> gcc_pcie_N_pipe_clk > > But here you're saying that you're setting the parent of PHY::pipe_clk > to gcc_pcie_N_pipe_clk? > Yeah, I will correct that statement. >> This is a new requirement for sc7280. >> For accessing to DBI registers during L23, >> need to switch the pipe clock with free-running >> clock (TCXO) using GCC’s registers > > So in previous platforms we could access DBI registers, in L23, without > any clock? > > What happens if we use xo as parent for the pipe clock > From SC7280 onwards, POR value for "gcc_pcie_N_pipe_clk_src" is TCX0. we need TCXO as parent to enable gdsc and then once PHY init successful we are changing gcc_pcie_N_pipe_clk_src to PHY pipe clk. In system suspend call back GDSC will be disabled and gcc_pcie_N_pipe_clk_src changed to TCX0. In the same way resume call back switching back gcc_pcie_N_pipe_clk_src to PHY pipe clk . >> >> Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org> >> --- >> drivers/pci/controller/dwc/pcie-qcom.c | 22 ++++++++++++++++++++++ >> 1 file changed, 22 insertions(+) >> >> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c >> b/drivers/pci/controller/dwc/pcie-qcom.c >> index 8a7a300..80e9ee4 100644 >> --- a/drivers/pci/controller/dwc/pcie-qcom.c >> +++ b/drivers/pci/controller/dwc/pcie-qcom.c >> @@ -166,6 +166,9 @@ struct qcom_pcie_resources_2_7_0 { >> struct regulator_bulk_data supplies[2]; >> struct reset_control *pci_reset; >> struct clk *pipe_clk; >> + struct clk *pipe_clk_mux; >> + struct clk *pipe_ext_src; >> + struct clk *ref_clk_src; >> }; >> >> union qcom_pcie_resources { >> @@ -1167,6 +1170,20 @@ static int qcom_pcie_get_resources_2_7_0(struct >> qcom_pcie *pcie) >> if (ret < 0) >> return ret; >> >> + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) { > > So this is the first 2.7.0 that has this need? Are we just going to add > more compatibles to this list going forward? > Will check and confirm whether above change will be applicable to future targets or not. >> + res->pipe_clk_mux = devm_clk_get(dev, "pipe_mux"); >> + if (IS_ERR(res->pipe_clk_mux)) >> + return PTR_ERR(res->pipe_clk_mux); > > So this is gcc_pcie_N_pipe_clk_src? > Yes >> + >> + res->pipe_ext_src = devm_clk_get(dev, "phy_pipe"); >> + if (IS_ERR(res->pipe_ext_src)) >> + return PTR_ERR(res->pipe_ext_src); > > And this is the pipe_clk coming out of the PHY (What I call > PHY::pipe_clk above)? > Yes >> + >> + res->ref_clk_src = devm_clk_get(dev, "ref"); >> + if (IS_ERR(res->ref_clk_src)) >> + return PTR_ERR(res->ref_clk_src); > > And this is TCXO? > Yes >> + } >> + >> res->pipe_clk = devm_clk_get(dev, "pipe"); >> return PTR_ERR_OR_ZERO(res->pipe_clk); >> } >> @@ -1255,6 +1272,11 @@ static void qcom_pcie_deinit_2_7_0(struct >> qcom_pcie *pcie) >> static int qcom_pcie_post_init_2_7_0(struct qcom_pcie *pcie) >> { >> struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; >> + struct dw_pcie *pci = pcie->pci; >> + struct device *dev = pci->dev; >> + >> + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) >> + clk_set_parent(res->pipe_clk_mux, res->pipe_ext_src); >> > > So after phy_power_on() (not "phy init" as you say in the commit > message, perhaps you don't mean phy_init() but in general terms "phy > initialization") you need to make sure that gcc_pcie_N_pipe_clk_src is > actually fed by PHY::pipe_clk? > > 1) What's the gcc_pcie_N_pipe_clk_src parent before this? > TCXO is POR value. > 2) Will the PHY initialization really succeed if the pipe_clk feeding > back from gcc isn't based on the PHY's pipe_clk? Is this a change in > sc7280? > PHY init will be successful but PCIe link will not be initialized. yes, this change is only applicable to SC7280. > 3) In the commit message you're talking about the need to make XO the > parent of gcc_pcie_N_pipe_clk_src during L23, where in this patch does > that happen? > Changes are in validation stage. will submit them soon in coming releases. Just mentioned the purpose of mux settings. > Regards, > Bjorn > >> return clk_prepare_enable(res->pipe_clk); >> } >> -- >> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora >> Forum, >> a Linux Foundation Collaborative Project >>
diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c index 8a7a300..80e9ee4 100644 --- a/drivers/pci/controller/dwc/pcie-qcom.c +++ b/drivers/pci/controller/dwc/pcie-qcom.c @@ -166,6 +166,9 @@ struct qcom_pcie_resources_2_7_0 { struct regulator_bulk_data supplies[2]; struct reset_control *pci_reset; struct clk *pipe_clk; + struct clk *pipe_clk_mux; + struct clk *pipe_ext_src; + struct clk *ref_clk_src; }; union qcom_pcie_resources { @@ -1167,6 +1170,20 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie) if (ret < 0) return ret; + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) { + res->pipe_clk_mux = devm_clk_get(dev, "pipe_mux"); + if (IS_ERR(res->pipe_clk_mux)) + return PTR_ERR(res->pipe_clk_mux); + + res->pipe_ext_src = devm_clk_get(dev, "phy_pipe"); + if (IS_ERR(res->pipe_ext_src)) + return PTR_ERR(res->pipe_ext_src); + + res->ref_clk_src = devm_clk_get(dev, "ref"); + if (IS_ERR(res->ref_clk_src)) + return PTR_ERR(res->ref_clk_src); + } + res->pipe_clk = devm_clk_get(dev, "pipe"); return PTR_ERR_OR_ZERO(res->pipe_clk); } @@ -1255,6 +1272,11 @@ static void qcom_pcie_deinit_2_7_0(struct qcom_pcie *pcie) static int qcom_pcie_post_init_2_7_0(struct qcom_pcie *pcie) { struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0; + struct dw_pcie *pci = pcie->pci; + struct device *dev = pci->dev; + + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) + clk_set_parent(res->pipe_clk_mux, res->pipe_ext_src); return clk_prepare_enable(res->pipe_clk); }
pipe-clk mux needs to switch between pipe_clk and XO as part of LPM squence. This is done by setting pipe_clk mux as parent of pipe_clk after phy init. This is a new requirement for sc7280. For accessing to DBI registers during L23, need to switch the pipe clock with free-running clock (TCXO) using GCC’s registers Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org> --- drivers/pci/controller/dwc/pcie-qcom.c | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)