| Message ID | 1630098658-23149-1-git-send-email-khsieh@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v2] phy: qcom-qmp: add support for display port voltage and pre-emphasis swing | expand |
On 28/08/2021 00:10, Kuogee Hsieh wrote: > Both voltage and pre-emphasis swing level are set during link training > negotiation between host and sink. There are totally four tables added. > A voltage swing table for both hbr and hbr1, a voltage table for both > hbr2 and hbr3, a pre-emphasis table for both hbr and hbr1 and a pre-emphasis > table for both hbr2 and hbr3. In addition, write 0x0a to TX_TX_POL_INV is > added to complete the sequence of configure dp phy base on HPG. > > Chnages in v2: > -- revise commit test > -- add Fixes tag > -- replaced voltage_swing_cfg with voltage > -- replaced pre_emphasis_cfg with emphasis > -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_v4_phy_configure_dp_swing() > -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_phy_configure_dp_swing() > > Fixes: aff188feb5e1 ("phy: qcom-qmp: add support for sm8250-usb3-dp phy") > Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> > --- > drivers/phy/qualcomm/phy-qcom-qmp.c | 117 ++++++++++++++++++++++++++---------- > 1 file changed, 85 insertions(+), 32 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c > index 31036aa..021cbb0 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c > @@ -3546,12 +3546,11 @@ static const u8 qmp_dp_v3_voltage_swing_hbr_rbr[4][4] = { > { 0x1f, 0xff, 0xff, 0xff } > }; > > -static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, > - unsigned int drv_lvl_reg, unsigned int emp_post_reg) > +static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy) As this becomes a v3-only function, could you please rename it to qcom_qmp_v3_phy_configure_dp_swing() > { > const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; > unsigned int v_level = 0, p_level = 0; > - u8 voltage_swing_cfg, pre_emphasis_cfg; > + u8 voltage, emphasis; > int i; > > for (i = 0; i < dp_opts->lanes; i++) { > @@ -3560,26 +3559,25 @@ static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, > } > > if (dp_opts->link_rate <= 2700) { > - voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr_rbr[v_level][p_level]; > - pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr_rbr[v_level][p_level]; > + voltage = qmp_dp_v3_voltage_swing_hbr_rbr[v_level][p_level]; > + emphasis = qmp_dp_v3_pre_emphasis_hbr_rbr[v_level][p_level]; > } else { > - voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr3_hbr2[v_level][p_level]; > - pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr3_hbr2[v_level][p_level]; > + voltage = qmp_dp_v3_voltage_swing_hbr3_hbr2[v_level][p_level]; > + emphasis = qmp_dp_v3_pre_emphasis_hbr3_hbr2[v_level][p_level]; > } > > /* TODO: Move check to config check */ > - if (voltage_swing_cfg == 0xFF && pre_emphasis_cfg == 0xFF) > + if (voltage == 0xFF && emphasis == 0xFF) > return -EINVAL; > > /* Enable MUX to use Cursor values from these registers */ > - voltage_swing_cfg |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; > - pre_emphasis_cfg |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; > - > - writel(voltage_swing_cfg, qphy->tx + drv_lvl_reg); > - writel(pre_emphasis_cfg, qphy->tx + emp_post_reg); > - writel(voltage_swing_cfg, qphy->tx2 + drv_lvl_reg); > - writel(pre_emphasis_cfg, qphy->tx2 + emp_post_reg); > + voltage |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; > + emphasis |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; > > + writel(voltage, qphy->tx + QSERDES_V3_TX_TX_DRV_LVL); > + writel(emphasis, qphy->tx + QSERDES_V3_TX_TX_EMP_POST1_LVL); > + writel(voltage, qphy->tx2 + QSERDES_V3_TX_TX_DRV_LVL); > + writel(emphasis, qphy->tx2 + QSERDES_V3_TX_TX_EMP_POST1_LVL); > return 0; > } > > @@ -3588,9 +3586,7 @@ static void qcom_qmp_v3_phy_configure_dp_tx(struct qmp_phy *qphy) > const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; > u32 bias_en, drvr_en; > > - if (qcom_qmp_phy_configure_dp_swing(qphy, > - QSERDES_V3_TX_TX_DRV_LVL, > - QSERDES_V3_TX_TX_EMP_POST1_LVL) < 0) > + if (qcom_qmp_phy_configure_dp_swing(qphy) < 0) > return; > > if (dp_opts->lanes == 1) { > @@ -3728,6 +3724,71 @@ static int qcom_qmp_v3_dp_phy_calibrate(struct qmp_phy *qphy) > return 0; > } > > +/* The values in these tables are given without MUX_EN (0x20) bit set */ > +static const u8 qmp_dp_v4_pre_emphasis_hbr3_hbr2[4][4] = { > + { 0x00, 0x0c, 0x15, 0x1b }, > + { 0x02, 0x0e, 0x16, 0xff }, > + { 0x02, 0x11, 0xff, 0xff }, > + { 0x04, 0xff, 0xff, 0xff } > +}; > + > +static const u8 qmp_dp_v4_voltage_swing_hbr3_hbr2[4][4] = { > + { 0x02, 0x12, 0x16, 0x1a }, > + { 0x09, 0x19, 0x1f, 0xff }, > + { 0x10, 0x1f, 0xff, 0xff }, > + { 0x1f, 0xff, 0xff, 0xff } > +}; > + > +static const u8 qmp_dp_v4_pre_emphasis_hbr_rbr[4][4] = { > + { 0x00, 0x0e, 0x15, 0x1b }, > + { 0x00, 0x0e, 0x15, 0xff }, > + { 0x00, 0x0e, 0xff, 0xff }, > + { 0x04, 0xff, 0xff, 0xff } > +}; > + > +static const u8 qmp_dp_v4_voltage_swing_hbr_rbr[4][4] = { > + { 0x08, 0x0f, 0x16, 0x1f }, > + { 0x11, 0x1e, 0x1f, 0xff }, > + { 0x16, 0x1f, 0xff, 0xff }, > + { 0x1f, 0xff, 0xff, 0xff } > +}; > + > +static int qcom_qmp_v4_phy_configure_dp_swing(struct qmp_phy *qphy) > +{ > + const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; > + unsigned int v_level = 0, p_level = 0; > + u8 voltage, emphasis; > + int i; > + > + for (i = 0; i < dp_opts->lanes; i++) { > + v_level = max(v_level, dp_opts->voltage[i]); > + p_level = max(p_level, dp_opts->pre[i]); > + } > + > + if (dp_opts->link_rate <= 2700) { > + voltage = qmp_dp_v4_voltage_swing_hbr_rbr[v_level][p_level]; > + emphasis = qmp_dp_v4_pre_emphasis_hbr_rbr[v_level][p_level]; > + } else { > + voltage = qmp_dp_v4_voltage_swing_hbr3_hbr2[v_level][p_level]; > + emphasis = qmp_dp_v4_pre_emphasis_hbr3_hbr2[v_level][p_level]; > + } > + > + /* TODO: Move check to config check */ > + if (voltage == 0xFF && emphasis == 0xFF) > + return -EINVAL; > + > + /* Enable MUX to use Cursor values from these registers */ > + voltage |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; > + emphasis |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; > + > + writel(voltage, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); > + writel(emphasis, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); > + writel(voltage, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); > + writel(emphasis, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL); > + > + return 0; > +} > + > static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy) > { > writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_PSR_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | > @@ -3757,16 +3818,7 @@ static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy) > > static void qcom_qmp_v4_phy_configure_dp_tx(struct qmp_phy *qphy) > { > - /* Program default values before writing proper values */ > - writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); > - writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); > - > - writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); > - writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL); > - > - qcom_qmp_phy_configure_dp_swing(qphy, > - QSERDES_V4_TX_TX_DRV_LVL, > - QSERDES_V4_TX_TX_EMP_POST1_LVL); > + qcom_qmp_v4_phy_configure_dp_swing(qphy); > } > > static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) > @@ -3885,6 +3937,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) > writel(drvr1_en, qphy->tx2 + QSERDES_V4_TX_HIGHZ_DRVR_EN); > writel(bias1_en, qphy->tx2 + QSERDES_V4_TX_TRANSCEIVER_BIAS_EN); > > + writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV); > + writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV); > + > writel(0x18, qphy->pcs + QSERDES_DP_PHY_CFG); > udelay(2000); > writel(0x19, qphy->pcs + QSERDES_DP_PHY_CFG); > @@ -3896,11 +3951,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) > 10000)) > return -ETIMEDOUT; > > - writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV); > - writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV); > > - writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); > - writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); > + writel(0x22, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); > + writel(0x22, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); > > writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); > writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL); >
Quoting Dmitry Baryshkov (2021-09-03 12:09:14) > On 28/08/2021 00:10, Kuogee Hsieh wrote: > > Both voltage and pre-emphasis swing level are set during link training > > negotiation between host and sink. There are totally four tables added. > > A voltage swing table for both hbr and hbr1, a voltage table for both > > hbr2 and hbr3, a pre-emphasis table for both hbr and hbr1 and a pre-emphasis > > table for both hbr2 and hbr3. In addition, write 0x0a to TX_TX_POL_INV is > > added to complete the sequence of configure dp phy base on HPG. > > > > Chnages in v2: > > -- revise commit test > > -- add Fixes tag > > -- replaced voltage_swing_cfg with voltage > > -- replaced pre_emphasis_cfg with emphasis > > -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_v4_phy_configure_dp_swing() > > -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_phy_configure_dp_swing() > > > > Fixes: aff188feb5e1 ("phy: qcom-qmp: add support for sm8250-usb3-dp phy") > > Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> > > --- > > drivers/phy/qualcomm/phy-qcom-qmp.c | 117 ++++++++++++++++++++++++++---------- > > 1 file changed, 85 insertions(+), 32 deletions(-) > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c > > index 31036aa..021cbb0 100644 > > --- a/drivers/phy/qualcomm/phy-qcom-qmp.c > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c > > @@ -3546,12 +3546,11 @@ static const u8 qmp_dp_v3_voltage_swing_hbr_rbr[4][4] = { > > { 0x1f, 0xff, 0xff, 0xff } > > }; > > > > -static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, > > - unsigned int drv_lvl_reg, unsigned int emp_post_reg) > > +static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy) > > As this becomes a v3-only function, could you please rename it to > qcom_qmp_v3_phy_configure_dp_swing() Can it be combined with the v4 version instead? The code structure is essentially the same, modulo the tables used and the register offset written to.
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c index 31036aa..021cbb0 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c @@ -3546,12 +3546,11 @@ static const u8 qmp_dp_v3_voltage_swing_hbr_rbr[4][4] = { { 0x1f, 0xff, 0xff, 0xff } }; -static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, - unsigned int drv_lvl_reg, unsigned int emp_post_reg) +static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy) { const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; unsigned int v_level = 0, p_level = 0; - u8 voltage_swing_cfg, pre_emphasis_cfg; + u8 voltage, emphasis; int i; for (i = 0; i < dp_opts->lanes; i++) { @@ -3560,26 +3559,25 @@ static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, } if (dp_opts->link_rate <= 2700) { - voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr_rbr[v_level][p_level]; - pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr_rbr[v_level][p_level]; + voltage = qmp_dp_v3_voltage_swing_hbr_rbr[v_level][p_level]; + emphasis = qmp_dp_v3_pre_emphasis_hbr_rbr[v_level][p_level]; } else { - voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr3_hbr2[v_level][p_level]; - pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr3_hbr2[v_level][p_level]; + voltage = qmp_dp_v3_voltage_swing_hbr3_hbr2[v_level][p_level]; + emphasis = qmp_dp_v3_pre_emphasis_hbr3_hbr2[v_level][p_level]; } /* TODO: Move check to config check */ - if (voltage_swing_cfg == 0xFF && pre_emphasis_cfg == 0xFF) + if (voltage == 0xFF && emphasis == 0xFF) return -EINVAL; /* Enable MUX to use Cursor values from these registers */ - voltage_swing_cfg |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; - pre_emphasis_cfg |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; - - writel(voltage_swing_cfg, qphy->tx + drv_lvl_reg); - writel(pre_emphasis_cfg, qphy->tx + emp_post_reg); - writel(voltage_swing_cfg, qphy->tx2 + drv_lvl_reg); - writel(pre_emphasis_cfg, qphy->tx2 + emp_post_reg); + voltage |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; + emphasis |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; + writel(voltage, qphy->tx + QSERDES_V3_TX_TX_DRV_LVL); + writel(emphasis, qphy->tx + QSERDES_V3_TX_TX_EMP_POST1_LVL); + writel(voltage, qphy->tx2 + QSERDES_V3_TX_TX_DRV_LVL); + writel(emphasis, qphy->tx2 + QSERDES_V3_TX_TX_EMP_POST1_LVL); return 0; } @@ -3588,9 +3586,7 @@ static void qcom_qmp_v3_phy_configure_dp_tx(struct qmp_phy *qphy) const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; u32 bias_en, drvr_en; - if (qcom_qmp_phy_configure_dp_swing(qphy, - QSERDES_V3_TX_TX_DRV_LVL, - QSERDES_V3_TX_TX_EMP_POST1_LVL) < 0) + if (qcom_qmp_phy_configure_dp_swing(qphy) < 0) return; if (dp_opts->lanes == 1) { @@ -3728,6 +3724,71 @@ static int qcom_qmp_v3_dp_phy_calibrate(struct qmp_phy *qphy) return 0; } +/* The values in these tables are given without MUX_EN (0x20) bit set */ +static const u8 qmp_dp_v4_pre_emphasis_hbr3_hbr2[4][4] = { + { 0x00, 0x0c, 0x15, 0x1b }, + { 0x02, 0x0e, 0x16, 0xff }, + { 0x02, 0x11, 0xff, 0xff }, + { 0x04, 0xff, 0xff, 0xff } +}; + +static const u8 qmp_dp_v4_voltage_swing_hbr3_hbr2[4][4] = { + { 0x02, 0x12, 0x16, 0x1a }, + { 0x09, 0x19, 0x1f, 0xff }, + { 0x10, 0x1f, 0xff, 0xff }, + { 0x1f, 0xff, 0xff, 0xff } +}; + +static const u8 qmp_dp_v4_pre_emphasis_hbr_rbr[4][4] = { + { 0x00, 0x0e, 0x15, 0x1b }, + { 0x00, 0x0e, 0x15, 0xff }, + { 0x00, 0x0e, 0xff, 0xff }, + { 0x04, 0xff, 0xff, 0xff } +}; + +static const u8 qmp_dp_v4_voltage_swing_hbr_rbr[4][4] = { + { 0x08, 0x0f, 0x16, 0x1f }, + { 0x11, 0x1e, 0x1f, 0xff }, + { 0x16, 0x1f, 0xff, 0xff }, + { 0x1f, 0xff, 0xff, 0xff } +}; + +static int qcom_qmp_v4_phy_configure_dp_swing(struct qmp_phy *qphy) +{ + const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; + unsigned int v_level = 0, p_level = 0; + u8 voltage, emphasis; + int i; + + for (i = 0; i < dp_opts->lanes; i++) { + v_level = max(v_level, dp_opts->voltage[i]); + p_level = max(p_level, dp_opts->pre[i]); + } + + if (dp_opts->link_rate <= 2700) { + voltage = qmp_dp_v4_voltage_swing_hbr_rbr[v_level][p_level]; + emphasis = qmp_dp_v4_pre_emphasis_hbr_rbr[v_level][p_level]; + } else { + voltage = qmp_dp_v4_voltage_swing_hbr3_hbr2[v_level][p_level]; + emphasis = qmp_dp_v4_pre_emphasis_hbr3_hbr2[v_level][p_level]; + } + + /* TODO: Move check to config check */ + if (voltage == 0xFF && emphasis == 0xFF) + return -EINVAL; + + /* Enable MUX to use Cursor values from these registers */ + voltage |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; + emphasis |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; + + writel(voltage, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); + writel(emphasis, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); + writel(voltage, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); + writel(emphasis, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL); + + return 0; +} + static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy) { writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_PSR_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | @@ -3757,16 +3818,7 @@ static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy) static void qcom_qmp_v4_phy_configure_dp_tx(struct qmp_phy *qphy) { - /* Program default values before writing proper values */ - writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); - writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); - - writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); - writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL); - - qcom_qmp_phy_configure_dp_swing(qphy, - QSERDES_V4_TX_TX_DRV_LVL, - QSERDES_V4_TX_TX_EMP_POST1_LVL); + qcom_qmp_v4_phy_configure_dp_swing(qphy); } static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) @@ -3885,6 +3937,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) writel(drvr1_en, qphy->tx2 + QSERDES_V4_TX_HIGHZ_DRVR_EN); writel(bias1_en, qphy->tx2 + QSERDES_V4_TX_TRANSCEIVER_BIAS_EN); + writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV); + writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV); + writel(0x18, qphy->pcs + QSERDES_DP_PHY_CFG); udelay(2000); writel(0x19, qphy->pcs + QSERDES_DP_PHY_CFG); @@ -3896,11 +3951,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) 10000)) return -ETIMEDOUT; - writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV); - writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV); - writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); - writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); + writel(0x22, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); + writel(0x22, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL);
Both voltage and pre-emphasis swing level are set during link training negotiation between host and sink. There are totally four tables added. A voltage swing table for both hbr and hbr1, a voltage table for both hbr2 and hbr3, a pre-emphasis table for both hbr and hbr1 and a pre-emphasis table for both hbr2 and hbr3. In addition, write 0x0a to TX_TX_POL_INV is added to complete the sequence of configure dp phy base on HPG. Chnages in v2: -- revise commit test -- add Fixes tag -- replaced voltage_swing_cfg with voltage -- replaced pre_emphasis_cfg with emphasis -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_v4_phy_configure_dp_swing() -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_phy_configure_dp_swing() Fixes: aff188feb5e1 ("phy: qcom-qmp: add support for sm8250-usb3-dp phy") Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> --- drivers/phy/qualcomm/phy-qcom-qmp.c | 117 ++++++++++++++++++++++++++---------- 1 file changed, 85 insertions(+), 32 deletions(-)