@@ -592,10 +592,6 @@ void dp_catalog_ctrl_hpd_config(struct dp_catalog *dp_catalog)
u32 reftimer = dp_read_aux(catalog, REG_DP_DP_HPD_REFTIMER);
- /* enable HPD plug and unplug interrupts */
- dp_catalog_hpd_config_intr(dp_catalog,
- DP_DP_HPD_PLUG_INT_MASK | DP_DP_HPD_UNPLUG_INT_MASK, true);
-
/* Configure REFTIMER and enable it */
reftimer |= DP_DP_HPD_REFTIMER_ENABLE;
dp_write_aux(catalog, REG_DP_DP_HPD_REFTIMER, reftimer);
@@ -622,13 +618,14 @@ u32 dp_catalog_hpd_get_intr_status(struct dp_catalog *dp_catalog)
{
struct dp_catalog_private *catalog = container_of(dp_catalog,
struct dp_catalog_private, dp_catalog);
- int isr = 0;
+ int isr, mask;
isr = dp_read_aux(catalog, REG_DP_DP_HPD_INT_STATUS);
dp_write_aux(catalog, REG_DP_DP_HPD_INT_ACK,
(isr & DP_DP_HPD_INT_MASK));
+ mask = dp_read_aux(catalog, REG_DP_DP_HPD_INT_MASK);
- return isr;
+ return isr & (DP_DP_HPD_STATE_STATUS_MASK | mask);
}
int dp_catalog_ctrl_get_interrupt(struct dp_catalog *dp_catalog)
@@ -687,7 +687,8 @@ static int dp_hpd_unplug_handle(struct dp_display_private *dp, u32 data)
dp_display_handle_plugged_change(&dp->dp_display, false);
/* enable HDP plug interrupt to prepare for next plugin */
- dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK, true);
+ if (dp->dp_display.connector_type == DRM_MODE_CONNECTOR_DisplayPort)
+ dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK, true);
DRM_DEBUG_DP("After, type=%d hpd_state=%d\n",
dp->dp_display.connector_type, state);
@@ -1096,10 +1097,17 @@ void msm_dp_snapshot(struct msm_disp_state *disp_state, struct msm_dp *dp)
static void dp_display_config_hpd(struct dp_display_private *dp)
{
-
dp_display_host_init(dp);
+
dp_catalog_ctrl_hpd_config(dp->catalog);
+ /* Enable plug and unplug interrupts only for external DisplayPort */
+ if (dp->dp_display.connector_type == DRM_MODE_CONNECTOR_DisplayPort)
+ dp_catalog_hpd_config_intr(dp->catalog,
+ DP_DP_HPD_PLUG_INT_MASK |
+ DP_DP_HPD_UNPLUG_INT_MASK,
+ true);
+
/* Enable interrupt first time
* we are leaving dp clocks on during disconnect
* and never disable interrupt
@@ -1383,6 +1391,12 @@ static int dp_pm_resume(struct device *dev)
dp_catalog_ctrl_hpd_config(dp->catalog);
+ if (dp->dp_display.connector_type == DRM_MODE_CONNECTOR_DisplayPort)
+ dp_catalog_hpd_config_intr(dp->catalog,
+ DP_DP_HPD_PLUG_INT_MASK |
+ DP_DP_HPD_UNPLUG_INT_MASK,
+ true);
+
if (dp_catalog_link_is_connected(dp->catalog)) {
/*
* set sink to normal operation mode -- D0
@@ -1647,6 +1661,9 @@ void dp_bridge_enable(struct drm_bridge *drm_bridge)
return;
}
+ if (dp->connector_type == DRM_MODE_CONNECTOR_eDP)
+ dp_hpd_plug_handle(dp_display, 0);
+
mutex_lock(&dp_display->event_mutex);
/* stop sentinel checking */
@@ -1711,6 +1728,9 @@ void dp_bridge_post_disable(struct drm_bridge *drm_bridge)
dp_display = container_of(dp, struct dp_display_private, dp_display);
+ if (dp->connector_type == DRM_MODE_CONNECTOR_eDP)
+ dp_hpd_unplug_handle(dp_display, 0);
+
mutex_lock(&dp_display->event_mutex);
/* stop sentinel checking */
The panel-edp enables the eDP panel power during probe, get_modes and enable. The eDP connect and disconnect interrupts for the eDP/DP controller are directly dependent on panel power. As eDP display can be assumed as always connected, the controller driver can skip the eDP connect and disconnect interrupts. Any disruption in the link status will be indicated via the IRQ_HPD interrupts. So, the eDP controller driver can just enable the IRQ_HPD and replug interrupts. The DP controller driver still needs to enable all the interrupts. The interrupt register will still reflect the connect and disconnect interrupt status without generating an actual HW interrupt. The controller driver should not handle those masked interrupts. Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com> --- drivers/gpu/drm/msm/dp/dp_catalog.c | 9 +++------ drivers/gpu/drm/msm/dp/dp_display.c | 24 ++++++++++++++++++++++-- 2 files changed, 25 insertions(+), 8 deletions(-)