| Message ID | 1652379802-8318-3-git-send-email-quic_kriskura@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | USB DWC3 host wake up support from system suspend | expand |
On Thu, May 12, 2022 at 11:53:19PM +0530, Krishna Kurapati wrote: > From: Sandeep Maheswaram <quic_c_sanm@quicinc.com> > > During suspend read the status of all port and set hs phy mode > based on current speed. Use this hs phy mode to configure wakeup > interrupts in qcom glue driver. > > Check wakeup-source property for dwc3 core node to set the > wakeup capability. Drop the device_init_wakeup call from > runtime suspend and resume. > > Also check during suspend if any wakeup capable devices are > connected to the controller (directly or through hubs), if there > are none set a flag to indicate that the PHY is powered > down during suspend. > > Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com> > Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> > --- > drivers/usb/dwc3/core.c | 30 +++++++++++++++++------------- > drivers/usb/dwc3/core.h | 4 ++++ > drivers/usb/dwc3/host.c | 24 ++++++++++++++++++++++++ > 3 files changed, 45 insertions(+), 13 deletions(-) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index 01115df..8bcabc5 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -1785,6 +1785,7 @@ static int dwc3_probe(struct platform_device *pdev) > > platform_set_drvdata(pdev, dwc); > dwc3_cache_hwparams(dwc); > + device_init_wakeup(&pdev->dev, of_property_read_bool(dev->of_node, "wakeup-source")); > > spin_lock_init(&dwc->lock); > mutex_init(&dwc->mutex); > @@ -1946,10 +1947,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) > dwc3_core_exit(dwc); > break; > case DWC3_GCTL_PRTCAP_HOST: > - if (!PMSG_IS_AUTO(msg)) { > - dwc3_core_exit(dwc); > - break; > - } > + dwc3_check_phy_speed_mode(dwc); > > /* Let controller to suspend HSPHY before PHY driver suspends */ > if (dwc->dis_u2_susphy_quirk || > @@ -1965,6 +1963,15 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) > > phy_pm_runtime_put_sync(dwc->usb2_generic_phy); > phy_pm_runtime_put_sync(dwc->usb3_generic_phy); > + > + if (!PMSG_IS_AUTO(msg)) { > + if (device_may_wakeup(dwc->dev)) I think this should be device_can_wakeup(), i.e. hardware capability instead of device policy. A drawback of powering the PHYs off is that it causes a high power consumption of certain peripherals if VBUS is still supplied, so this should be limited to platforms where the PHYs must be powered off (using wakeup capability as a proxy for now). > + dwc->phy_power_off = false; > + else { > + dwc->phy_power_off = true; > + dwc3_core_exit(dwc); > + } > + } > break; > case DWC3_GCTL_PRTCAP_OTG: > /* do nothing during runtime_suspend */ > @@ -2008,11 +2015,12 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) > break; > case DWC3_GCTL_PRTCAP_HOST: > if (!PMSG_IS_AUTO(msg)) { > - ret = dwc3_core_init_for_resume(dwc); > - if (ret) > - return ret; > - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); > - break; > + if (dwc->phy_power_off) { > + ret = dwc3_core_init_for_resume(dwc); > + if (ret) > + return ret; > + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); > + } > } > /* Restore GUSB2PHYCFG bits that were modified in suspend */ > reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); > @@ -2084,8 +2092,6 @@ static int dwc3_runtime_suspend(struct device *dev) > if (ret) > return ret; > > - device_init_wakeup(dev, true); > - > return 0; > } > > @@ -2094,8 +2100,6 @@ static int dwc3_runtime_resume(struct device *dev) > struct dwc3 *dwc = dev_get_drvdata(dev); > int ret; > > - device_init_wakeup(dev, false); > - > ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME); > if (ret) > return ret; > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > index 81c486b..37397a8 100644 > --- a/drivers/usb/dwc3/core.h > +++ b/drivers/usb/dwc3/core.h > @@ -1155,6 +1155,9 @@ struct dwc3 { > > bool phys_ready; > > + unsigned int hs_phy_mode; > + bool phy_power_off; > + > struct ulpi *ulpi; > bool ulpi_ready; > > @@ -1539,6 +1542,7 @@ int dwc3_core_soft_reset(struct dwc3 *dwc); > #if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE) > int dwc3_host_init(struct dwc3 *dwc); > void dwc3_host_exit(struct dwc3 *dwc); > +void dwc3_check_phy_speed_mode(struct dwc3 *dwc); > #else > static inline int dwc3_host_init(struct dwc3 *dwc) > { return 0; } > diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c > index f56c30c..e19b40a 100644 > --- a/drivers/usb/dwc3/host.c > +++ b/drivers/usb/dwc3/host.c > @@ -12,6 +12,7 @@ > #include <linux/platform_device.h> > > #include "core.h" > +#include "../host/xhci.h" > > static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc, > int irq, char *name) > @@ -136,3 +137,26 @@ void dwc3_host_exit(struct dwc3 *dwc) > { > platform_device_unregister(dwc->xhci); > } > + > +void dwc3_check_phy_speed_mode(struct dwc3 *dwc) > +{ > + int i, num_ports; > + u32 reg; > + struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); > + struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd); > + > + dwc->hs_phy_mode = 0; > + > + reg = readl(&xhci_hcd->cap_regs->hcs_params1); > + > + num_ports = HCS_MAX_PORTS(reg); > + for (i = 0; i < num_ports; i++) { > + reg = readl(&xhci_hcd->op_regs->port_status_base + i * NUM_PORT_REGS); > + if (reg & PORT_PE) { > + if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg)) > + dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS; > + else if (DEV_LOWSPEED(reg)) > + dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS; > + } > + } > +} I anticipate that it might raise concerns from maintainers that dwc3_check_phy_speed_mode() accesses xHCI data structures and registers directly. Could there be a generic HCD API that provides this functionality (if implemented by the specific HCD)?
On 5/13/2022 4:10 AM, Matthias Kaehlcke wrote: > On Thu, May 12, 2022 at 11:53:19PM +0530, Krishna Kurapati wrote: >> From: Sandeep Maheswaram <quic_c_sanm@quicinc.com> >> >> During suspend read the status of all port and set hs phy mode >> based on current speed. Use this hs phy mode to configure wakeup >> interrupts in qcom glue driver. >> >> Check wakeup-source property for dwc3 core node to set the >> wakeup capability. Drop the device_init_wakeup call from >> runtime suspend and resume. >> >> Also check during suspend if any wakeup capable devices are >> connected to the controller (directly or through hubs), if there >> are none set a flag to indicate that the PHY is powered >> down during suspend. >> >> Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com> >> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> >> --- >> drivers/usb/dwc3/core.c | 30 +++++++++++++++++------------- >> drivers/usb/dwc3/core.h | 4 ++++ >> drivers/usb/dwc3/host.c | 24 ++++++++++++++++++++++++ >> 3 files changed, 45 insertions(+), 13 deletions(-) >> >> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c >> index 01115df..8bcabc5 100644 >> --- a/drivers/usb/dwc3/core.c >> +++ b/drivers/usb/dwc3/core.c >> @@ -1785,6 +1785,7 @@ static int dwc3_probe(struct platform_device *pdev) >> >> platform_set_drvdata(pdev, dwc); >> dwc3_cache_hwparams(dwc); >> + device_init_wakeup(&pdev->dev, of_property_read_bool(dev->of_node, "wakeup-source")); >> >> spin_lock_init(&dwc->lock); >> mutex_init(&dwc->mutex); >> @@ -1946,10 +1947,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) >> dwc3_core_exit(dwc); >> break; >> case DWC3_GCTL_PRTCAP_HOST: >> - if (!PMSG_IS_AUTO(msg)) { >> - dwc3_core_exit(dwc); >> - break; >> - } >> + dwc3_check_phy_speed_mode(dwc); >> >> /* Let controller to suspend HSPHY before PHY driver suspends */ >> if (dwc->dis_u2_susphy_quirk || >> @@ -1965,6 +1963,15 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) >> >> phy_pm_runtime_put_sync(dwc->usb2_generic_phy); >> phy_pm_runtime_put_sync(dwc->usb3_generic_phy); >> + >> + if (!PMSG_IS_AUTO(msg)) { >> + if (device_may_wakeup(dwc->dev)) > I think this should be device_can_wakeup(), i.e. hardware capability instead of > device policy. A drawback of powering the PHYs off is that it causes a high > power consumption of certain peripherals if VBUS is still supplied, so this > should be limited to platforms where the PHYs must be powered off (using wakeup > capability as a proxy for now). Thnaks Mathias for the review. Will make this change in the next patchset. >> + dwc->phy_power_off = false; >> + else { >> + dwc->phy_power_off = true; >> + dwc3_core_exit(dwc); >> + } >> + } >> break; >> case DWC3_GCTL_PRTCAP_OTG: >> /* do nothing during runtime_suspend */ >> @@ -2008,11 +2015,12 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) >> break; >> case DWC3_GCTL_PRTCAP_HOST: >> if (!PMSG_IS_AUTO(msg)) { >> - ret = dwc3_core_init_for_resume(dwc); >> - if (ret) >> - return ret; >> - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); >> - break; >> + if (dwc->phy_power_off) { >> + ret = dwc3_core_init_for_resume(dwc); >> + if (ret) >> + return ret; >> + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); >> + } >> } >> /* Restore GUSB2PHYCFG bits that were modified in suspend */ >> reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); >> @@ -2084,8 +2092,6 @@ static int dwc3_runtime_suspend(struct device *dev) >> if (ret) >> return ret; >> >> - device_init_wakeup(dev, true); >> - >> return 0; >> } >> >> @@ -2094,8 +2100,6 @@ static int dwc3_runtime_resume(struct device *dev) >> struct dwc3 *dwc = dev_get_drvdata(dev); >> int ret; >> >> - device_init_wakeup(dev, false); >> - >> ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME); >> if (ret) >> return ret; >> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h >> index 81c486b..37397a8 100644 >> --- a/drivers/usb/dwc3/core.h >> +++ b/drivers/usb/dwc3/core.h >> @@ -1155,6 +1155,9 @@ struct dwc3 { >> >> bool phys_ready; >> >> + unsigned int hs_phy_mode; >> + bool phy_power_off; >> + >> struct ulpi *ulpi; >> bool ulpi_ready; >> >> @@ -1539,6 +1542,7 @@ int dwc3_core_soft_reset(struct dwc3 *dwc); >> #if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE) >> int dwc3_host_init(struct dwc3 *dwc); >> void dwc3_host_exit(struct dwc3 *dwc); >> +void dwc3_check_phy_speed_mode(struct dwc3 *dwc); >> #else >> static inline int dwc3_host_init(struct dwc3 *dwc) >> { return 0; } >> diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c >> index f56c30c..e19b40a 100644 >> --- a/drivers/usb/dwc3/host.c >> +++ b/drivers/usb/dwc3/host.c >> @@ -12,6 +12,7 @@ >> #include <linux/platform_device.h> >> >> #include "core.h" >> +#include "../host/xhci.h" >> >> static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc, >> int irq, char *name) >> @@ -136,3 +137,26 @@ void dwc3_host_exit(struct dwc3 *dwc) >> { >> platform_device_unregister(dwc->xhci); >> } >> + >> +void dwc3_check_phy_speed_mode(struct dwc3 *dwc) >> +{ >> + int i, num_ports; >> + u32 reg; >> + struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); >> + struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd); >> + >> + dwc->hs_phy_mode = 0; >> + >> + reg = readl(&xhci_hcd->cap_regs->hcs_params1); >> + >> + num_ports = HCS_MAX_PORTS(reg); >> + for (i = 0; i < num_ports; i++) { >> + reg = readl(&xhci_hcd->op_regs->port_status_base + i * NUM_PORT_REGS); >> + if (reg & PORT_PE) { >> + if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg)) >> + dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS; >> + else if (DEV_LOWSPEED(reg)) >> + dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS; >> + } >> + } >> +} > I anticipate that it might raise concerns from maintainers that > dwc3_check_phy_speed_mode() accesses xHCI data structures and > registers directly. Could there be a generic HCD API that provides > this functionality (if implemented by the specific HCD)? Hi Mathias, we are not sure if there is any such API present currently. Hi Alan, can you help suggest any API (if present) that we can reuse here to avoid xhci registers and structs here in dwc3.
On Fri, May 13, 2022 at 09:28:16AM +0530, Krishna Kurapati PSSNV wrote: > > On 5/13/2022 4:10 AM, Matthias Kaehlcke wrote: > >On Thu, May 12, 2022 at 11:53:19PM +0530, Krishna Kurapati wrote: > >>From: Sandeep Maheswaram <quic_c_sanm@quicinc.com> > >> > >>During suspend read the status of all port and set hs phy mode > >>based on current speed. Use this hs phy mode to configure wakeup > >>interrupts in qcom glue driver. > >> > >>Check wakeup-source property for dwc3 core node to set the > >>wakeup capability. Drop the device_init_wakeup call from > >>runtime suspend and resume. > >> > >>Also check during suspend if any wakeup capable devices are > >>connected to the controller (directly or through hubs), if there > >>are none set a flag to indicate that the PHY is powered > >>down during suspend. > >> > >>Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com> > >>Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> > >>--- > >> drivers/usb/dwc3/core.c | 30 +++++++++++++++++------------- > >> drivers/usb/dwc3/core.h | 4 ++++ > >> drivers/usb/dwc3/host.c | 24 ++++++++++++++++++++++++ > >> 3 files changed, 45 insertions(+), 13 deletions(-) > >> > >>diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > >>index 01115df..8bcabc5 100644 > >>--- a/drivers/usb/dwc3/core.c > >>+++ b/drivers/usb/dwc3/core.c > >>@@ -1785,6 +1785,7 @@ static int dwc3_probe(struct platform_device *pdev) > >> platform_set_drvdata(pdev, dwc); > >> dwc3_cache_hwparams(dwc); > >>+ device_init_wakeup(&pdev->dev, of_property_read_bool(dev->of_node, "wakeup-source")); > >> spin_lock_init(&dwc->lock); > >> mutex_init(&dwc->mutex); > >>@@ -1946,10 +1947,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) > >> dwc3_core_exit(dwc); > >> break; > >> case DWC3_GCTL_PRTCAP_HOST: > >>- if (!PMSG_IS_AUTO(msg)) { > >>- dwc3_core_exit(dwc); > >>- break; > >>- } > >>+ dwc3_check_phy_speed_mode(dwc); > >> /* Let controller to suspend HSPHY before PHY driver suspends */ > >> if (dwc->dis_u2_susphy_quirk || > >>@@ -1965,6 +1963,15 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) > >> phy_pm_runtime_put_sync(dwc->usb2_generic_phy); > >> phy_pm_runtime_put_sync(dwc->usb3_generic_phy); > >>+ > >>+ if (!PMSG_IS_AUTO(msg)) { > >>+ if (device_may_wakeup(dwc->dev)) > >I think this should be device_can_wakeup(), i.e. hardware capability instead of > >device policy. A drawback of powering the PHYs off is that it causes a high > >power consumption of certain peripherals if VBUS is still supplied, so this > >should be limited to platforms where the PHYs must be powered off (using wakeup > >capability as a proxy for now). > Thnaks Mathias for the review. Will make this change in the next patchset. > >>+ dwc->phy_power_off = false; > >>+ else { > >>+ dwc->phy_power_off = true; > >>+ dwc3_core_exit(dwc); > >>+ } > >>+ } > >> break; > >> case DWC3_GCTL_PRTCAP_OTG: > >> /* do nothing during runtime_suspend */ > >>@@ -2008,11 +2015,12 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) > >> break; > >> case DWC3_GCTL_PRTCAP_HOST: > >> if (!PMSG_IS_AUTO(msg)) { > >>- ret = dwc3_core_init_for_resume(dwc); > >>- if (ret) > >>- return ret; > >>- dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); > >>- break; > >>+ if (dwc->phy_power_off) { > >>+ ret = dwc3_core_init_for_resume(dwc); > >>+ if (ret) > >>+ return ret; > >>+ dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); > >>+ } > >> } > >> /* Restore GUSB2PHYCFG bits that were modified in suspend */ > >> reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); > >>@@ -2084,8 +2092,6 @@ static int dwc3_runtime_suspend(struct device *dev) > >> if (ret) > >> return ret; > >>- device_init_wakeup(dev, true); > >>- > >> return 0; > >> } > >>@@ -2094,8 +2100,6 @@ static int dwc3_runtime_resume(struct device *dev) > >> struct dwc3 *dwc = dev_get_drvdata(dev); > >> int ret; > >>- device_init_wakeup(dev, false); > >>- > >> ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME); > >> if (ret) > >> return ret; > >>diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > >>index 81c486b..37397a8 100644 > >>--- a/drivers/usb/dwc3/core.h > >>+++ b/drivers/usb/dwc3/core.h > >>@@ -1155,6 +1155,9 @@ struct dwc3 { > >> bool phys_ready; > >>+ unsigned int hs_phy_mode; > >>+ bool phy_power_off; > >>+ > >> struct ulpi *ulpi; > >> bool ulpi_ready; > >>@@ -1539,6 +1542,7 @@ int dwc3_core_soft_reset(struct dwc3 *dwc); > >> #if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE) > >> int dwc3_host_init(struct dwc3 *dwc); > >> void dwc3_host_exit(struct dwc3 *dwc); > >>+void dwc3_check_phy_speed_mode(struct dwc3 *dwc); > >> #else > >> static inline int dwc3_host_init(struct dwc3 *dwc) > >> { return 0; } > >>diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c > >>index f56c30c..e19b40a 100644 > >>--- a/drivers/usb/dwc3/host.c > >>+++ b/drivers/usb/dwc3/host.c > >>@@ -12,6 +12,7 @@ > >> #include <linux/platform_device.h> > >> #include "core.h" > >>+#include "../host/xhci.h" > >> static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc, > >> int irq, char *name) > >>@@ -136,3 +137,26 @@ void dwc3_host_exit(struct dwc3 *dwc) > >> { > >> platform_device_unregister(dwc->xhci); > >> } > >>+ > >>+void dwc3_check_phy_speed_mode(struct dwc3 *dwc) > >>+{ > >>+ int i, num_ports; > >>+ u32 reg; > >>+ struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); > >>+ struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd); > >>+ > >>+ dwc->hs_phy_mode = 0; > >>+ > >>+ reg = readl(&xhci_hcd->cap_regs->hcs_params1); > >>+ > >>+ num_ports = HCS_MAX_PORTS(reg); > >>+ for (i = 0; i < num_ports; i++) { > >>+ reg = readl(&xhci_hcd->op_regs->port_status_base + i * NUM_PORT_REGS); > >>+ if (reg & PORT_PE) { > >>+ if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg)) > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS; > >>+ else if (DEV_LOWSPEED(reg)) > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS; > >>+ } > >>+ } > >>+} > >I anticipate that it might raise concerns from maintainers that > >dwc3_check_phy_speed_mode() accesses xHCI data structures and > >registers directly. Could there be a generic HCD API that provides > >this functionality (if implemented by the specific HCD)? > > Hi Mathias, we are not sure if there is any such API present currently. > > Hi Alan, can you help suggest any API (if present) that we can reuse here to > avoid > > xhci registers and structs here in dwc3. > We can probably do something like below to query the speed. This avoids adding another API and does not touch the underlying registers. Pls define enum usb_device_speed usb2_speed in dwc3 structure. diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c index f29a264..fed1c58 100644 --- a/drivers/usb/dwc3/host.c +++ b/drivers/usb/dwc3/host.c @@ -9,9 +9,29 @@ #include <linux/acpi.h> #include <linux/platform_device.h> +#include <linux/usb.h> #include "core.h" +void dwc3_update_hs_phy_speed(struct dwc3 *dwc) +{ + struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); + struct usb_device *udev; + + /* + * It is possible to query the speed of all children of + * USB2.0 root hub via usb_hub_for_each_child(). DWC3 code + * currently supports only 1 port per controller. So + * this is sufficient. + */ + udev = usb_hub_find_child(hcd->self.root_hub, 1); + + if (udev) + dwc->usb2_speed = udev->speed; + else + dwc->usb2_speed = USB_SPEED_UNKNOWN; +} + static int dwc3_host_get_irq(struct dwc3 *dwc) { struct platform_device *dwc3_pdev = to_platform_device(dwc->dev); Thanks, Pavan
On Mon, May 16, 2022 at 10:13:27AM +0530, Pavan Kondeti wrote: > On Fri, May 13, 2022 at 09:28:16AM +0530, Krishna Kurapati PSSNV wrote: > > > > On 5/13/2022 4:10 AM, Matthias Kaehlcke wrote: > > >On Thu, May 12, 2022 at 11:53:19PM +0530, Krishna Kurapati wrote: > > >>From: Sandeep Maheswaram <quic_c_sanm@quicinc.com> > > >> > > >>During suspend read the status of all port and set hs phy mode > > >>based on current speed. Use this hs phy mode to configure wakeup > > >>interrupts in qcom glue driver. > > >> > > >>Check wakeup-source property for dwc3 core node to set the > > >>wakeup capability. Drop the device_init_wakeup call from > > >>runtime suspend and resume. > > >> > > >>Also check during suspend if any wakeup capable devices are > > >>connected to the controller (directly or through hubs), if there > > >>are none set a flag to indicate that the PHY is powered > > >>down during suspend. > > >> > > >>Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com> > > >>Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> > > >>--- > > >> drivers/usb/dwc3/core.c | 30 +++++++++++++++++------------- > > >> drivers/usb/dwc3/core.h | 4 ++++ > > >> drivers/usb/dwc3/host.c | 24 ++++++++++++++++++++++++ > > >> 3 files changed, 45 insertions(+), 13 deletions(-) > > >> > > >>diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > > >>index 01115df..8bcabc5 100644 > > >>--- a/drivers/usb/dwc3/core.c > > >>+++ b/drivers/usb/dwc3/core.c > > >>@@ -1785,6 +1785,7 @@ static int dwc3_probe(struct platform_device *pdev) > > >> platform_set_drvdata(pdev, dwc); > > >> dwc3_cache_hwparams(dwc); > > >>+ device_init_wakeup(&pdev->dev, of_property_read_bool(dev->of_node, "wakeup-source")); > > >> spin_lock_init(&dwc->lock); > > >> mutex_init(&dwc->mutex); > > >>@@ -1946,10 +1947,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) > > >> dwc3_core_exit(dwc); > > >> break; > > >> case DWC3_GCTL_PRTCAP_HOST: > > >>- if (!PMSG_IS_AUTO(msg)) { > > >>- dwc3_core_exit(dwc); > > >>- break; > > >>- } > > >>+ dwc3_check_phy_speed_mode(dwc); > > >> /* Let controller to suspend HSPHY before PHY driver suspends */ > > >> if (dwc->dis_u2_susphy_quirk || > > >>@@ -1965,6 +1963,15 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) > > >> phy_pm_runtime_put_sync(dwc->usb2_generic_phy); > > >> phy_pm_runtime_put_sync(dwc->usb3_generic_phy); > > >>+ > > >>+ if (!PMSG_IS_AUTO(msg)) { > > >>+ if (device_may_wakeup(dwc->dev)) > > >I think this should be device_can_wakeup(), i.e. hardware capability instead of > > >device policy. A drawback of powering the PHYs off is that it causes a high > > >power consumption of certain peripherals if VBUS is still supplied, so this > > >should be limited to platforms where the PHYs must be powered off (using wakeup > > >capability as a proxy for now). > > Thnaks Mathias for the review. Will make this change in the next patchset. > > >>+ dwc->phy_power_off = false; > > >>+ else { > > >>+ dwc->phy_power_off = true; > > >>+ dwc3_core_exit(dwc); > > >>+ } > > >>+ } > > >> break; > > >> case DWC3_GCTL_PRTCAP_OTG: > > >> /* do nothing during runtime_suspend */ > > >>@@ -2008,11 +2015,12 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) > > >> break; > > >> case DWC3_GCTL_PRTCAP_HOST: > > >> if (!PMSG_IS_AUTO(msg)) { > > >>- ret = dwc3_core_init_for_resume(dwc); > > >>- if (ret) > > >>- return ret; > > >>- dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); > > >>- break; > > >>+ if (dwc->phy_power_off) { > > >>+ ret = dwc3_core_init_for_resume(dwc); > > >>+ if (ret) > > >>+ return ret; > > >>+ dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); > > >>+ } > > >> } > > >> /* Restore GUSB2PHYCFG bits that were modified in suspend */ > > >> reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); > > >>@@ -2084,8 +2092,6 @@ static int dwc3_runtime_suspend(struct device *dev) > > >> if (ret) > > >> return ret; > > >>- device_init_wakeup(dev, true); > > >>- > > >> return 0; > > >> } > > >>@@ -2094,8 +2100,6 @@ static int dwc3_runtime_resume(struct device *dev) > > >> struct dwc3 *dwc = dev_get_drvdata(dev); > > >> int ret; > > >>- device_init_wakeup(dev, false); > > >>- > > >> ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME); > > >> if (ret) > > >> return ret; > > >>diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > > >>index 81c486b..37397a8 100644 > > >>--- a/drivers/usb/dwc3/core.h > > >>+++ b/drivers/usb/dwc3/core.h > > >>@@ -1155,6 +1155,9 @@ struct dwc3 { > > >> bool phys_ready; > > >>+ unsigned int hs_phy_mode; > > >>+ bool phy_power_off; > > >>+ > > >> struct ulpi *ulpi; > > >> bool ulpi_ready; > > >>@@ -1539,6 +1542,7 @@ int dwc3_core_soft_reset(struct dwc3 *dwc); > > >> #if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE) > > >> int dwc3_host_init(struct dwc3 *dwc); > > >> void dwc3_host_exit(struct dwc3 *dwc); > > >>+void dwc3_check_phy_speed_mode(struct dwc3 *dwc); > > >> #else > > >> static inline int dwc3_host_init(struct dwc3 *dwc) > > >> { return 0; } > > >>diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c > > >>index f56c30c..e19b40a 100644 > > >>--- a/drivers/usb/dwc3/host.c > > >>+++ b/drivers/usb/dwc3/host.c > > >>@@ -12,6 +12,7 @@ > > >> #include <linux/platform_device.h> > > >> #include "core.h" > > >>+#include "../host/xhci.h" > > >> static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc, > > >> int irq, char *name) > > >>@@ -136,3 +137,26 @@ void dwc3_host_exit(struct dwc3 *dwc) > > >> { > > >> platform_device_unregister(dwc->xhci); > > >> } > > >>+ > > >>+void dwc3_check_phy_speed_mode(struct dwc3 *dwc) > > >>+{ > > >>+ int i, num_ports; > > >>+ u32 reg; > > >>+ struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); > > >>+ struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd); > > >>+ > > >>+ dwc->hs_phy_mode = 0; > > >>+ > > >>+ reg = readl(&xhci_hcd->cap_regs->hcs_params1); > > >>+ > > >>+ num_ports = HCS_MAX_PORTS(reg); > > >>+ for (i = 0; i < num_ports; i++) { > > >>+ reg = readl(&xhci_hcd->op_regs->port_status_base + i * NUM_PORT_REGS); > > >>+ if (reg & PORT_PE) { > > >>+ if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg)) > > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS; > > >>+ else if (DEV_LOWSPEED(reg)) > > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS; > > >>+ } > > >>+ } > > >>+} > > >I anticipate that it might raise concerns from maintainers that > > >dwc3_check_phy_speed_mode() accesses xHCI data structures and > > >registers directly. Could there be a generic HCD API that provides > > >this functionality (if implemented by the specific HCD)? > > > > Hi Mathias, we are not sure if there is any such API present currently. > > > > Hi Alan, can you help suggest any API (if present) that we can reuse here to > > avoid > > > > xhci registers and structs here in dwc3. > > > > We can probably do something like below to query the speed. This avoids adding > another API and does not touch the underlying registers. > > Pls define enum usb_device_speed usb2_speed in dwc3 structure. > > diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c > index f29a264..fed1c58 100644 > --- a/drivers/usb/dwc3/host.c > +++ b/drivers/usb/dwc3/host.c > @@ -9,9 +9,29 @@ > > #include <linux/acpi.h> > #include <linux/platform_device.h> > +#include <linux/usb.h> > > #include "core.h" > > +void dwc3_update_hs_phy_speed(struct dwc3 *dwc) > +{ > + struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); > + struct usb_device *udev; > + > + /* > + * It is possible to query the speed of all children of > + * USB2.0 root hub via usb_hub_for_each_child(). DWC3 code > + * currently supports only 1 port per controller. So > + * this is sufficient. > + */ > + udev = usb_hub_find_child(hcd->self.root_hub, 1); > + > + if (udev) > + dwc->usb2_speed = udev->speed; > + else > + dwc->usb2_speed = USB_SPEED_UNKNOWN; > +} > + > static int dwc3_host_get_irq(struct dwc3 *dwc) > { > struct platform_device *dwc3_pdev = to_platform_device(dwc->dev); > > I am also thinking why dwc core needs to cache usb2_speed since dwc3-qcom glue driver is the only sole user. We also require it only during suspend and does not bother about dwc::usb2_speed correctness outside suspend. Lets move this to dwc3-qcom suspend routines where we have to rely on USB2 speed for configuring the D+/D- interrupt. Thanks, Pavan
On Mon, May 16, 2022 at 08:34:45PM +0530, Pavan Kondeti wrote: > On Mon, May 16, 2022 at 10:13:27AM +0530, Pavan Kondeti wrote: > > On Fri, May 13, 2022 at 09:28:16AM +0530, Krishna Kurapati PSSNV wrote: > > > > > > On 5/13/2022 4:10 AM, Matthias Kaehlcke wrote: > > > >On Thu, May 12, 2022 at 11:53:19PM +0530, Krishna Kurapati wrote: > > > >>From: Sandeep Maheswaram <quic_c_sanm@quicinc.com> > > > >> > > > >>During suspend read the status of all port and set hs phy mode > > > >>based on current speed. Use this hs phy mode to configure wakeup > > > >>interrupts in qcom glue driver. > > > >> > > > >>Check wakeup-source property for dwc3 core node to set the > > > >>wakeup capability. Drop the device_init_wakeup call from > > > >>runtime suspend and resume. > > > >> > > > >>Also check during suspend if any wakeup capable devices are > > > >>connected to the controller (directly or through hubs), if there > > > >>are none set a flag to indicate that the PHY is powered > > > >>down during suspend. > > > >> > > > >>Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com> > > > >>Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> > > > >>--- > > > >> drivers/usb/dwc3/core.c | 30 +++++++++++++++++------------- > > > >> drivers/usb/dwc3/core.h | 4 ++++ > > > >> drivers/usb/dwc3/host.c | 24 ++++++++++++++++++++++++ > > > >> 3 files changed, 45 insertions(+), 13 deletions(-) > > > >> > > > >>diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > > > >>index 01115df..8bcabc5 100644 > > > >>--- a/drivers/usb/dwc3/core.c > > > >>+++ b/drivers/usb/dwc3/core.c > > > >>@@ -1785,6 +1785,7 @@ static int dwc3_probe(struct platform_device *pdev) > > > >> platform_set_drvdata(pdev, dwc); > > > >> dwc3_cache_hwparams(dwc); > > > >>+ device_init_wakeup(&pdev->dev, of_property_read_bool(dev->of_node, "wakeup-source")); > > > >> spin_lock_init(&dwc->lock); > > > >> mutex_init(&dwc->mutex); > > > >>@@ -1946,10 +1947,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) > > > >> dwc3_core_exit(dwc); > > > >> break; > > > >> case DWC3_GCTL_PRTCAP_HOST: > > > >>- if (!PMSG_IS_AUTO(msg)) { > > > >>- dwc3_core_exit(dwc); > > > >>- break; > > > >>- } > > > >>+ dwc3_check_phy_speed_mode(dwc); > > > >> /* Let controller to suspend HSPHY before PHY driver suspends */ > > > >> if (dwc->dis_u2_susphy_quirk || > > > >>@@ -1965,6 +1963,15 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) > > > >> phy_pm_runtime_put_sync(dwc->usb2_generic_phy); > > > >> phy_pm_runtime_put_sync(dwc->usb3_generic_phy); > > > >>+ > > > >>+ if (!PMSG_IS_AUTO(msg)) { > > > >>+ if (device_may_wakeup(dwc->dev)) > > > >I think this should be device_can_wakeup(), i.e. hardware capability instead of > > > >device policy. A drawback of powering the PHYs off is that it causes a high > > > >power consumption of certain peripherals if VBUS is still supplied, so this > > > >should be limited to platforms where the PHYs must be powered off (using wakeup > > > >capability as a proxy for now). > > > Thnaks Mathias for the review. Will make this change in the next patchset. > > > >>+ dwc->phy_power_off = false; > > > >>+ else { > > > >>+ dwc->phy_power_off = true; > > > >>+ dwc3_core_exit(dwc); > > > >>+ } > > > >>+ } > > > >> break; > > > >> case DWC3_GCTL_PRTCAP_OTG: > > > >> /* do nothing during runtime_suspend */ > > > >>@@ -2008,11 +2015,12 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) > > > >> break; > > > >> case DWC3_GCTL_PRTCAP_HOST: > > > >> if (!PMSG_IS_AUTO(msg)) { > > > >>- ret = dwc3_core_init_for_resume(dwc); > > > >>- if (ret) > > > >>- return ret; > > > >>- dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); > > > >>- break; > > > >>+ if (dwc->phy_power_off) { > > > >>+ ret = dwc3_core_init_for_resume(dwc); > > > >>+ if (ret) > > > >>+ return ret; > > > >>+ dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); > > > >>+ } > > > >> } > > > >> /* Restore GUSB2PHYCFG bits that were modified in suspend */ > > > >> reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); > > > >>@@ -2084,8 +2092,6 @@ static int dwc3_runtime_suspend(struct device *dev) > > > >> if (ret) > > > >> return ret; > > > >>- device_init_wakeup(dev, true); > > > >>- > > > >> return 0; > > > >> } > > > >>@@ -2094,8 +2100,6 @@ static int dwc3_runtime_resume(struct device *dev) > > > >> struct dwc3 *dwc = dev_get_drvdata(dev); > > > >> int ret; > > > >>- device_init_wakeup(dev, false); > > > >>- > > > >> ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME); > > > >> if (ret) > > > >> return ret; > > > >>diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > > > >>index 81c486b..37397a8 100644 > > > >>--- a/drivers/usb/dwc3/core.h > > > >>+++ b/drivers/usb/dwc3/core.h > > > >>@@ -1155,6 +1155,9 @@ struct dwc3 { > > > >> bool phys_ready; > > > >>+ unsigned int hs_phy_mode; > > > >>+ bool phy_power_off; > > > >>+ > > > >> struct ulpi *ulpi; > > > >> bool ulpi_ready; > > > >>@@ -1539,6 +1542,7 @@ int dwc3_core_soft_reset(struct dwc3 *dwc); > > > >> #if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE) > > > >> int dwc3_host_init(struct dwc3 *dwc); > > > >> void dwc3_host_exit(struct dwc3 *dwc); > > > >>+void dwc3_check_phy_speed_mode(struct dwc3 *dwc); > > > >> #else > > > >> static inline int dwc3_host_init(struct dwc3 *dwc) > > > >> { return 0; } > > > >>diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c > > > >>index f56c30c..e19b40a 100644 > > > >>--- a/drivers/usb/dwc3/host.c > > > >>+++ b/drivers/usb/dwc3/host.c > > > >>@@ -12,6 +12,7 @@ > > > >> #include <linux/platform_device.h> > > > >> #include "core.h" > > > >>+#include "../host/xhci.h" > > > >> static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc, > > > >> int irq, char *name) > > > >>@@ -136,3 +137,26 @@ void dwc3_host_exit(struct dwc3 *dwc) > > > >> { > > > >> platform_device_unregister(dwc->xhci); > > > >> } > > > >>+ > > > >>+void dwc3_check_phy_speed_mode(struct dwc3 *dwc) > > > >>+{ > > > >>+ int i, num_ports; > > > >>+ u32 reg; > > > >>+ struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); > > > >>+ struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd); > > > >>+ > > > >>+ dwc->hs_phy_mode = 0; > > > >>+ > > > >>+ reg = readl(&xhci_hcd->cap_regs->hcs_params1); > > > >>+ > > > >>+ num_ports = HCS_MAX_PORTS(reg); > > > >>+ for (i = 0; i < num_ports; i++) { > > > >>+ reg = readl(&xhci_hcd->op_regs->port_status_base + i * NUM_PORT_REGS); > > > >>+ if (reg & PORT_PE) { > > > >>+ if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg)) > > > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS; > > > >>+ else if (DEV_LOWSPEED(reg)) > > > >>+ dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS; > > > >>+ } > > > >>+ } > > > >>+} > > > >I anticipate that it might raise concerns from maintainers that > > > >dwc3_check_phy_speed_mode() accesses xHCI data structures and > > > >registers directly. Could there be a generic HCD API that provides > > > >this functionality (if implemented by the specific HCD)? > > > > > > Hi Mathias, we are not sure if there is any such API present currently. > > > > > > Hi Alan, can you help suggest any API (if present) that we can reuse here to > > > avoid > > > > > > xhci registers and structs here in dwc3. > > > > > > > We can probably do something like below to query the speed. This avoids adding > > another API and does not touch the underlying registers. > > > > Pls define enum usb_device_speed usb2_speed in dwc3 structure. > > > > diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c > > index f29a264..fed1c58 100644 > > --- a/drivers/usb/dwc3/host.c > > +++ b/drivers/usb/dwc3/host.c > > @@ -9,9 +9,29 @@ > > > > #include <linux/acpi.h> > > #include <linux/platform_device.h> > > +#include <linux/usb.h> > > > > #include "core.h" > > > > +void dwc3_update_hs_phy_speed(struct dwc3 *dwc) > > +{ > > + struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); > > + struct usb_device *udev; > > + > > + /* > > + * It is possible to query the speed of all children of > > + * USB2.0 root hub via usb_hub_for_each_child(). DWC3 code > > + * currently supports only 1 port per controller. So > > + * this is sufficient. > > + */ > > + udev = usb_hub_find_child(hcd->self.root_hub, 1); > > + > > + if (udev) > > + dwc->usb2_speed = udev->speed; > > + else > > + dwc->usb2_speed = USB_SPEED_UNKNOWN; > > +} > > + > > static int dwc3_host_get_irq(struct dwc3 *dwc) > > { > > struct platform_device *dwc3_pdev = to_platform_device(dwc->dev); > > > > > I am also thinking why dwc core needs to cache usb2_speed since dwc3-qcom glue > driver is the only sole user. We also require it only during suspend and does > not bother about dwc::usb2_speed correctness outside suspend. Lets move this > to dwc3-qcom suspend routines where we have to rely on USB2 speed for > configuring the D+/D- interrupt. I like both of your suggestions. If something like dwc3_update_hs_phy_speed() works properly here we should have finally sorted out all the layering issues Felipe was unhappy about.
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index 01115df..8bcabc5 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -1785,6 +1785,7 @@ static int dwc3_probe(struct platform_device *pdev) platform_set_drvdata(pdev, dwc); dwc3_cache_hwparams(dwc); + device_init_wakeup(&pdev->dev, of_property_read_bool(dev->of_node, "wakeup-source")); spin_lock_init(&dwc->lock); mutex_init(&dwc->mutex); @@ -1946,10 +1947,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) dwc3_core_exit(dwc); break; case DWC3_GCTL_PRTCAP_HOST: - if (!PMSG_IS_AUTO(msg)) { - dwc3_core_exit(dwc); - break; - } + dwc3_check_phy_speed_mode(dwc); /* Let controller to suspend HSPHY before PHY driver suspends */ if (dwc->dis_u2_susphy_quirk || @@ -1965,6 +1963,15 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) phy_pm_runtime_put_sync(dwc->usb2_generic_phy); phy_pm_runtime_put_sync(dwc->usb3_generic_phy); + + if (!PMSG_IS_AUTO(msg)) { + if (device_may_wakeup(dwc->dev)) + dwc->phy_power_off = false; + else { + dwc->phy_power_off = true; + dwc3_core_exit(dwc); + } + } break; case DWC3_GCTL_PRTCAP_OTG: /* do nothing during runtime_suspend */ @@ -2008,11 +2015,12 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) break; case DWC3_GCTL_PRTCAP_HOST: if (!PMSG_IS_AUTO(msg)) { - ret = dwc3_core_init_for_resume(dwc); - if (ret) - return ret; - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); - break; + if (dwc->phy_power_off) { + ret = dwc3_core_init_for_resume(dwc); + if (ret) + return ret; + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); + } } /* Restore GUSB2PHYCFG bits that were modified in suspend */ reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); @@ -2084,8 +2092,6 @@ static int dwc3_runtime_suspend(struct device *dev) if (ret) return ret; - device_init_wakeup(dev, true); - return 0; } @@ -2094,8 +2100,6 @@ static int dwc3_runtime_resume(struct device *dev) struct dwc3 *dwc = dev_get_drvdata(dev); int ret; - device_init_wakeup(dev, false); - ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME); if (ret) return ret; diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index 81c486b..37397a8 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -1155,6 +1155,9 @@ struct dwc3 { bool phys_ready; + unsigned int hs_phy_mode; + bool phy_power_off; + struct ulpi *ulpi; bool ulpi_ready; @@ -1539,6 +1542,7 @@ int dwc3_core_soft_reset(struct dwc3 *dwc); #if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE) int dwc3_host_init(struct dwc3 *dwc); void dwc3_host_exit(struct dwc3 *dwc); +void dwc3_check_phy_speed_mode(struct dwc3 *dwc); #else static inline int dwc3_host_init(struct dwc3 *dwc) { return 0; } diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c index f56c30c..e19b40a 100644 --- a/drivers/usb/dwc3/host.c +++ b/drivers/usb/dwc3/host.c @@ -12,6 +12,7 @@ #include <linux/platform_device.h> #include "core.h" +#include "../host/xhci.h" static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc, int irq, char *name) @@ -136,3 +137,26 @@ void dwc3_host_exit(struct dwc3 *dwc) { platform_device_unregister(dwc->xhci); } + +void dwc3_check_phy_speed_mode(struct dwc3 *dwc) +{ + int i, num_ports; + u32 reg; + struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci); + struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd); + + dwc->hs_phy_mode = 0; + + reg = readl(&xhci_hcd->cap_regs->hcs_params1); + + num_ports = HCS_MAX_PORTS(reg); + for (i = 0; i < num_ports; i++) { + reg = readl(&xhci_hcd->op_regs->port_status_base + i * NUM_PORT_REGS); + if (reg & PORT_PE) { + if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg)) + dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS; + else if (DEV_LOWSPEED(reg)) + dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS; + } + } +}