| Message ID | 1662626705-13097-7-git-send-email-quic_taozha@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add support to configure TPDM DSB subunit | expand |
On 08/09/2022 09:45, Tao Zhang wrote: > Add node to set and show programming mode for TPDM DSB subunit. > Once the DSB programming mode is set, it will be written to the > register DSB_CR. Bit[10:9] of the DSB_CR register is used to set > the DSB test mode. > > Signed-off-by: Tao Zhang <quic_taozha@quicinc.com> > --- > drivers/hwtracing/coresight/coresight-tpdm.c | 49 +++++++++++++++++++++++++++- > drivers/hwtracing/coresight/coresight-tpdm.h | 10 ++++++ > 2 files changed, 58 insertions(+), 1 deletion(-) > > diff --git a/drivers/hwtracing/coresight/coresight-tpdm.c b/drivers/hwtracing/coresight/coresight-tpdm.c > index fae9963..7265793 100644 > --- a/drivers/hwtracing/coresight/coresight-tpdm.c > +++ b/drivers/hwtracing/coresight/coresight-tpdm.c > @@ -22,7 +22,7 @@ DEFINE_CORESIGHT_DEVLIST(tpdm_devs, "tpdm"); > > static void tpdm_enable_dsb(struct tpdm_drvdata *drvdata) > { > - u32 val; > + u32 val, mode; > > val = readl_relaxed(drvdata->base + TPDM_DSB_TIER); > /* Set trigger timestamp */ > @@ -42,6 +42,19 @@ static void tpdm_enable_dsb(struct tpdm_drvdata *drvdata) > > /* Set the enable bit of DSB control register to 1 */ > val = readl_relaxed(drvdata->base + TPDM_DSB_CR); > + /* Set the cycle accurate mode */ > + mode = TPDM_DSB_MODE_CYCACC(drvdata->dsb->mode); > + val = val & ~(0x7 << 9); > + val = val | (mode << 9); Please do not hard code numbers like that above. Please could you define proper masks for the fields in DSB_CR and use FIELD_GET, FIELD_PREP for setting the values. > + /* Set the byte lane for high-performance mode */ > + mode = TPDM_DSB_MODE_HPBYTESEL(drvdata->dsb->mode); > + val = val & ~(0x1F << 2); > + val = val | (mode << 2); > + /* Set the performance mode */ Same as above. > + if (drvdata->dsb->mode & TPDM_DSB_MODE_PERF) > + val |= TPDM_DSB_MODE; > + else > + val &= ~TPDM_DSB_MODE; > val |= TPDM_DSB_CR_ENA; > writel_relaxed(val, drvdata->base + TPDM_DSB_CR); > } > @@ -232,6 +245,39 @@ static struct attribute_group tpdm_attr_grp = { > .attrs = tpdm_attrs, > }; > > +static ssize_t dsb_mode_show(struct device *dev, > + struct device_attribute *attr, > + char *buf) > +{ > + struct tpdm_drvdata *drvdata = dev_get_drvdata(dev->parent); > + > + if (!(drvdata->datasets & TPDM_PIDR0_DS_DSB)) > + return -EPERM; As mentioned earlier, use is_visble() instead of hard coding this in every function. > + > + return scnprintf(buf, PAGE_SIZE, "%lx\n", > + (unsigned long)drvdata->dsb->mode); > +} > + > +static ssize_t dsb_mode_store(struct device *dev, > + struct device_attribute *attr, > + const char *buf, > + size_t size) > +{ > + struct tpdm_drvdata *drvdata = dev_get_drvdata(dev->parent); > + unsigned long val; > + > + if ((kstrtoul(buf, 16, &val)) || val < 0 || val > 3) Why not leave kstrtoul to detect the base instead of always forcing 16 ? Some other code had forced to base of 10. Please be flexible and avoid the inconsistencies. > + return -EINVAL; > + if (!(drvdata->datasets & TPDM_PIDR0_DS_DSB)) > + return -EPERM; > + > + spin_lock(&drvdata->spinlock); > + drvdata->dsb->mode = val & TPDM_MODE_ALL; > + spin_unlock(&drvdata->spinlock); > + return size; > +} > +static DEVICE_ATTR_RW(dsb_mode); > + > static ssize_t dsb_trig_type_show(struct device *dev, > struct device_attribute *attr, > char *buf) > @@ -312,6 +358,7 @@ static ssize_t dsb_trig_ts_store(struct device *dev, > } > static DEVICE_ATTR_RW(dsb_trig_ts); > static struct attribute *tpdm_dsb_attrs[] = { > + &dev_attr_dsb_mode.attr, > &dev_attr_dsb_trig_ts.attr, > &dev_attr_dsb_trig_type.attr, > NULL, > diff --git a/drivers/hwtracing/coresight/coresight-tpdm.h b/drivers/hwtracing/coresight/coresight-tpdm.h > index dd4a013..4d57488 100644 > --- a/drivers/hwtracing/coresight/coresight-tpdm.h > +++ b/drivers/hwtracing/coresight/coresight-tpdm.h > @@ -19,6 +19,14 @@ > #define TPDM_DSB_XTRIG_TSENAB BIT(1) > /* Enable bit for DSB subunit trigger type */ > #define TPDM_DSB_TRIG_TYPE BIT(12) > +/* Enable bit for DSB subunit perfmance mode */ > +#define TPDM_DSB_MODE BIT(1) > + > +/* DSB programming modes */ > +#define TPDM_DSB_MODE_CYCACC(val) BMVAL(val, 0, 2) > +#define TPDM_DSB_MODE_PERF BIT(3) > +#define TPDM_DSB_MODE_HPBYTESEL(val) BMVAL(val, 4, 8) Please could we use GENMASK to define the masks and use FIELD_GET/FILED_PREP macros for the dealing with the fields ? Similarly for the DSB_CR register please. Suzuki
Hi Suzuki, 在 10/24/2022 10:49 PM, Suzuki K Poulose 写道: > On 08/09/2022 09:45, Tao Zhang wrote: >> Add node to set and show programming mode for TPDM DSB subunit. >> Once the DSB programming mode is set, it will be written to the >> register DSB_CR. Bit[10:9] of the DSB_CR register is used to set >> the DSB test mode. >> >> Signed-off-by: Tao Zhang <quic_taozha@quicinc.com> >> --- >> drivers/hwtracing/coresight/coresight-tpdm.c | 49 >> +++++++++++++++++++++++++++- >> drivers/hwtracing/coresight/coresight-tpdm.h | 10 ++++++ >> 2 files changed, 58 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/hwtracing/coresight/coresight-tpdm.c >> b/drivers/hwtracing/coresight/coresight-tpdm.c >> index fae9963..7265793 100644 >> --- a/drivers/hwtracing/coresight/coresight-tpdm.c >> +++ b/drivers/hwtracing/coresight/coresight-tpdm.c >> @@ -22,7 +22,7 @@ DEFINE_CORESIGHT_DEVLIST(tpdm_devs, "tpdm"); >> static void tpdm_enable_dsb(struct tpdm_drvdata *drvdata) >> { >> - u32 val; >> + u32 val, mode; >> val = readl_relaxed(drvdata->base + TPDM_DSB_TIER); >> /* Set trigger timestamp */ >> @@ -42,6 +42,19 @@ static void tpdm_enable_dsb(struct tpdm_drvdata >> *drvdata) >> /* Set the enable bit of DSB control register to 1 */ >> val = readl_relaxed(drvdata->base + TPDM_DSB_CR); >> + /* Set the cycle accurate mode */ >> + mode = TPDM_DSB_MODE_CYCACC(drvdata->dsb->mode); >> + val = val & ~(0x7 << 9); >> + val = val | (mode << 9); > > Please do not hard code numbers like that above. Please could > you define proper masks for the fields in DSB_CR and use > FIELD_GET, FIELD_PREP for setting the values. > Sure, I will update this in the next patch series. >> + /* Set the byte lane for high-performance mode */ >> + mode = TPDM_DSB_MODE_HPBYTESEL(drvdata->dsb->mode); >> + val = val & ~(0x1F << 2); >> + val = val | (mode << 2); >> + /* Set the performance mode */ > > Same as above. > Sure, I will update this in the next patch series. >> + if (drvdata->dsb->mode & TPDM_DSB_MODE_PERF) >> + val |= TPDM_DSB_MODE; >> + else >> + val &= ~TPDM_DSB_MODE; >> val |= TPDM_DSB_CR_ENA; >> writel_relaxed(val, drvdata->base + TPDM_DSB_CR); >> } >> @@ -232,6 +245,39 @@ static struct attribute_group tpdm_attr_grp = { >> .attrs = tpdm_attrs, >> }; >> +static ssize_t dsb_mode_show(struct device *dev, >> + struct device_attribute *attr, >> + char *buf) >> +{ >> + struct tpdm_drvdata *drvdata = dev_get_drvdata(dev->parent); >> + >> + if (!(drvdata->datasets & TPDM_PIDR0_DS_DSB)) >> + return -EPERM; > > As mentioned earlier, use is_visble() instead of hard coding this > in every function. > Sure, I will update this in the next patch series. >> + >> + return scnprintf(buf, PAGE_SIZE, "%lx\n", >> + (unsigned long)drvdata->dsb->mode); >> +} >> + >> +static ssize_t dsb_mode_store(struct device *dev, >> + struct device_attribute *attr, >> + const char *buf, >> + size_t size) >> +{ >> + struct tpdm_drvdata *drvdata = dev_get_drvdata(dev->parent); >> + unsigned long val; >> + >> + if ((kstrtoul(buf, 16, &val)) || val < 0 || val > 3) > > Why not leave kstrtoul to detect the base instead of always forcing > 16 ? Some other code had forced to base of 10. Please be flexible > and avoid the inconsistencies. > Sure, I will update this in the next patch series. >> + return -EINVAL; >> + if (!(drvdata->datasets & TPDM_PIDR0_DS_DSB)) >> + return -EPERM; >> + >> + spin_lock(&drvdata->spinlock); >> + drvdata->dsb->mode = val & TPDM_MODE_ALL; >> + spin_unlock(&drvdata->spinlock); >> + return size; >> +} >> +static DEVICE_ATTR_RW(dsb_mode); >> + >> static ssize_t dsb_trig_type_show(struct device *dev, >> struct device_attribute *attr, >> char *buf) >> @@ -312,6 +358,7 @@ static ssize_t dsb_trig_ts_store(struct device *dev, >> } >> static DEVICE_ATTR_RW(dsb_trig_ts); >> static struct attribute *tpdm_dsb_attrs[] = { >> + &dev_attr_dsb_mode.attr, >> &dev_attr_dsb_trig_ts.attr, >> &dev_attr_dsb_trig_type.attr, >> NULL, >> diff --git a/drivers/hwtracing/coresight/coresight-tpdm.h >> b/drivers/hwtracing/coresight/coresight-tpdm.h >> index dd4a013..4d57488 100644 >> --- a/drivers/hwtracing/coresight/coresight-tpdm.h >> +++ b/drivers/hwtracing/coresight/coresight-tpdm.h >> @@ -19,6 +19,14 @@ >> #define TPDM_DSB_XTRIG_TSENAB BIT(1) >> /* Enable bit for DSB subunit trigger type */ >> #define TPDM_DSB_TRIG_TYPE BIT(12) >> +/* Enable bit for DSB subunit perfmance mode */ >> +#define TPDM_DSB_MODE BIT(1) >> + >> +/* DSB programming modes */ >> +#define TPDM_DSB_MODE_CYCACC(val) BMVAL(val, 0, 2) >> +#define TPDM_DSB_MODE_PERF BIT(3) >> +#define TPDM_DSB_MODE_HPBYTESEL(val) BMVAL(val, 4, 8) > > Please could we use GENMASK to define the masks and > use FIELD_GET/FILED_PREP macros for the dealing with > the fields ? > > Similarly for the DSB_CR register please. Sure, I will update this in the next patch series. > > Suzuki Best Regards Tao
diff --git a/drivers/hwtracing/coresight/coresight-tpdm.c b/drivers/hwtracing/coresight/coresight-tpdm.c index fae9963..7265793 100644 --- a/drivers/hwtracing/coresight/coresight-tpdm.c +++ b/drivers/hwtracing/coresight/coresight-tpdm.c @@ -22,7 +22,7 @@ DEFINE_CORESIGHT_DEVLIST(tpdm_devs, "tpdm"); static void tpdm_enable_dsb(struct tpdm_drvdata *drvdata) { - u32 val; + u32 val, mode; val = readl_relaxed(drvdata->base + TPDM_DSB_TIER); /* Set trigger timestamp */ @@ -42,6 +42,19 @@ static void tpdm_enable_dsb(struct tpdm_drvdata *drvdata) /* Set the enable bit of DSB control register to 1 */ val = readl_relaxed(drvdata->base + TPDM_DSB_CR); + /* Set the cycle accurate mode */ + mode = TPDM_DSB_MODE_CYCACC(drvdata->dsb->mode); + val = val & ~(0x7 << 9); + val = val | (mode << 9); + /* Set the byte lane for high-performance mode */ + mode = TPDM_DSB_MODE_HPBYTESEL(drvdata->dsb->mode); + val = val & ~(0x1F << 2); + val = val | (mode << 2); + /* Set the performance mode */ + if (drvdata->dsb->mode & TPDM_DSB_MODE_PERF) + val |= TPDM_DSB_MODE; + else + val &= ~TPDM_DSB_MODE; val |= TPDM_DSB_CR_ENA; writel_relaxed(val, drvdata->base + TPDM_DSB_CR); } @@ -232,6 +245,39 @@ static struct attribute_group tpdm_attr_grp = { .attrs = tpdm_attrs, }; +static ssize_t dsb_mode_show(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct tpdm_drvdata *drvdata = dev_get_drvdata(dev->parent); + + if (!(drvdata->datasets & TPDM_PIDR0_DS_DSB)) + return -EPERM; + + return scnprintf(buf, PAGE_SIZE, "%lx\n", + (unsigned long)drvdata->dsb->mode); +} + +static ssize_t dsb_mode_store(struct device *dev, + struct device_attribute *attr, + const char *buf, + size_t size) +{ + struct tpdm_drvdata *drvdata = dev_get_drvdata(dev->parent); + unsigned long val; + + if ((kstrtoul(buf, 16, &val)) || val < 0 || val > 3) + return -EINVAL; + if (!(drvdata->datasets & TPDM_PIDR0_DS_DSB)) + return -EPERM; + + spin_lock(&drvdata->spinlock); + drvdata->dsb->mode = val & TPDM_MODE_ALL; + spin_unlock(&drvdata->spinlock); + return size; +} +static DEVICE_ATTR_RW(dsb_mode); + static ssize_t dsb_trig_type_show(struct device *dev, struct device_attribute *attr, char *buf) @@ -312,6 +358,7 @@ static ssize_t dsb_trig_ts_store(struct device *dev, } static DEVICE_ATTR_RW(dsb_trig_ts); static struct attribute *tpdm_dsb_attrs[] = { + &dev_attr_dsb_mode.attr, &dev_attr_dsb_trig_ts.attr, &dev_attr_dsb_trig_type.attr, NULL, diff --git a/drivers/hwtracing/coresight/coresight-tpdm.h b/drivers/hwtracing/coresight/coresight-tpdm.h index dd4a013..4d57488 100644 --- a/drivers/hwtracing/coresight/coresight-tpdm.h +++ b/drivers/hwtracing/coresight/coresight-tpdm.h @@ -19,6 +19,14 @@ #define TPDM_DSB_XTRIG_TSENAB BIT(1) /* Enable bit for DSB subunit trigger type */ #define TPDM_DSB_TRIG_TYPE BIT(12) +/* Enable bit for DSB subunit perfmance mode */ +#define TPDM_DSB_MODE BIT(1) + +/* DSB programming modes */ +#define TPDM_DSB_MODE_CYCACC(val) BMVAL(val, 0, 2) +#define TPDM_DSB_MODE_PERF BIT(3) +#define TPDM_DSB_MODE_HPBYTESEL(val) BMVAL(val, 4, 8) +#define TPDM_MODE_ALL (0xFFFFFFF) /* TPDM integration test registers */ #define TPDM_ITATBCNTRL (0xEF0) @@ -48,10 +56,12 @@ /** * struct dsb_dataset - specifics associated to dsb dataset + * @mode: DSB programming mode * @trig_ts: Enable/Disable trigger timestamp. * @trig_type: Enable/Disable trigger type. */ struct dsb_dataset { + u32 mode; bool trig_ts; bool trig_type; };
Add node to set and show programming mode for TPDM DSB subunit. Once the DSB programming mode is set, it will be written to the register DSB_CR. Bit[10:9] of the DSB_CR register is used to set the DSB test mode. Signed-off-by: Tao Zhang <quic_taozha@quicinc.com> --- drivers/hwtracing/coresight/coresight-tpdm.c | 49 +++++++++++++++++++++++++++- drivers/hwtracing/coresight/coresight-tpdm.h | 10 ++++++ 2 files changed, 58 insertions(+), 1 deletion(-)