diff mbox series

[v2,4/7] scsi: ufs: ufs-qcom: Limit HS-G5 Rate-A to hosts with HW version 5

Message ID 1699332374-9324-5-git-send-email-cang@qti.qualcomm.com (mailing list archive)
State Not Applicable
Headers show
Series [v2,1/7] scsi: ufs: host: Rename structure ufs_dev_params to ufs_host_params | expand

Commit Message

Can Guo Nov. 7, 2023, 4:46 a.m. UTC 
From: Can Guo <quic_cang@quicinc.com>

Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.

Signed-off-by: Can Guo <quic_cang@quicinc.com>
---
 drivers/ufs/host/ufs-qcom.c | 18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)

Comments

Manivannan Sadhasivam Nov. 8, 2023, 5:25 a.m. UTC | #1 
On Mon, Nov 06, 2023 at 08:46:10PM -0800, Can Guo wrote:
> From: Can Guo <quic_cang@quicinc.com>
> 
> Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
> HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
> to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.
> 
> Signed-off-by: Can Guo <quic_cang@quicinc.com>
> ---
>  drivers/ufs/host/ufs-qcom.c | 18 +++++++++++++++++-
>  1 file changed, 17 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 60b35ca..55ee31d 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -442,9 +442,25 @@ static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba)
>  static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
>  {
>  	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> +	struct ufs_host_params *host_params = &host->host_params;
>  	struct phy *phy = host->generic_phy;
> +	enum phy_mode mode;
>  	int ret;
>  
> +	/*
> +	 * HW ver 5 can only support up to HS-G5 Rate-A due to HW limitations.

Does this limitation apply to future targets as well or just to SM8550? If
it's the latter, then we need to use a flag.

- Mani

> +	 * If the HS-G5 PHY gear is used, update host_params->hs_rate to Rate-A,
> +	 * so that the subsequent power mode change shall stick to Rate-A.
> +	 */
> +	if (host->hw_ver.major == 0x5) {
> +		if (host->phy_gear == UFS_HS_G5)
> +			host_params->hs_rate = PA_HS_MODE_A;
> +		else
> +			host_params->hs_rate = PA_HS_MODE_B;
> +	}
> +
> +	mode = host_params->hs_rate == PA_HS_MODE_B ? PHY_MODE_UFS_HS_B : PHY_MODE_UFS_HS_A;
> +
>  	/* Reset UFS Host Controller and PHY */
>  	ret = ufs_qcom_host_reset(hba);
>  	if (ret)
> @@ -459,7 +475,7 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
>  		return ret;
>  	}
>  
> -	phy_set_mode_ext(phy, PHY_MODE_UFS_HS_B, host->phy_gear);
> +	phy_set_mode_ext(phy, mode, host->phy_gear);
>  
>  	/* power on phy - start serdes and phy's power and clocks */
>  	ret = phy_power_on(phy);
> -- 
> 2.7.4
>
Can Guo Nov. 8, 2023, 8:42 a.m. UTC | #2 
Hi Mani,

On 11/8/2023 1:25 PM, Manivannan Sadhasivam wrote:
> On Mon, Nov 06, 2023 at 08:46:10PM -0800, Can Guo wrote:
>> From: Can Guo <quic_cang@quicinc.com>
>>
>> Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
>> HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
>> to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.
>>
>> Signed-off-by: Can Guo <quic_cang@quicinc.com>
>> ---
>>   drivers/ufs/host/ufs-qcom.c | 18 +++++++++++++++++-
>>   1 file changed, 17 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
>> index 60b35ca..55ee31d 100644
>> --- a/drivers/ufs/host/ufs-qcom.c
>> +++ b/drivers/ufs/host/ufs-qcom.c
>> @@ -442,9 +442,25 @@ static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba)
>>   static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
>>   {
>>   	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
>> +	struct ufs_host_params *host_params = &host->host_params;
>>   	struct phy *phy = host->generic_phy;
>> +	enum phy_mode mode;
>>   	int ret;
>>   
>> +	/*
>> +	 * HW ver 5 can only support up to HS-G5 Rate-A due to HW limitations.
> 
> Does this limitation apply to future targets as well or just to SM8550? If
> it's the latter, then we need to use a flag.
> 
> - ManiUFS host controller HW ver (major) 5 IPs (they may have different 
minor/step verions) can be used by many QCOM chipsets, so it applies to 
several available targets and future targets which are going to have HW 
ver 5 UFS host controller. This limitation goes away since HW ver 6.

Thanks,
Can Guo.
Manivannan Sadhasivam Nov. 9, 2023, 3:27 a.m. UTC | #3 
On Wed, Nov 08, 2023 at 04:42:42PM +0800, Can Guo wrote:
> Hi Mani,
> 
> On 11/8/2023 1:25 PM, Manivannan Sadhasivam wrote:
> > On Mon, Nov 06, 2023 at 08:46:10PM -0800, Can Guo wrote:
> > > From: Can Guo <quic_cang@quicinc.com>
> > > 
> > > Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
> > > HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
> > > to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.
> > > 
> > > Signed-off-by: Can Guo <quic_cang@quicinc.com>
> > > ---
> > >   drivers/ufs/host/ufs-qcom.c | 18 +++++++++++++++++-
> > >   1 file changed, 17 insertions(+), 1 deletion(-)
> > > 
> > > diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> > > index 60b35ca..55ee31d 100644
> > > --- a/drivers/ufs/host/ufs-qcom.c
> > > +++ b/drivers/ufs/host/ufs-qcom.c
> > > @@ -442,9 +442,25 @@ static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba)
> > >   static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
> > >   {
> > >   	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> > > +	struct ufs_host_params *host_params = &host->host_params;
> > >   	struct phy *phy = host->generic_phy;
> > > +	enum phy_mode mode;
> > >   	int ret;
> > > +	/*
> > > +	 * HW ver 5 can only support up to HS-G5 Rate-A due to HW limitations.
> > 
> > Does this limitation apply to future targets as well or just to SM8550? If
> > it's the latter, then we need to use a flag.
> > 
> > - ManiUFS host controller HW ver (major) 5 IPs (they may have different
> minor/step verions) can be used by many QCOM chipsets, so it applies to
> several available targets and future targets which are going to have HW ver
> 5 UFS host controller. This limitation goes away since HW ver 6.
> 

Okay, thanks for clarifying.

- Mani

> Thanks,
> Can Guo.
diff mbox series

Patch

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 60b35ca..55ee31d 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -442,9 +442,25 @@  static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba)
 static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
 {
 	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
+	struct ufs_host_params *host_params = &host->host_params;
 	struct phy *phy = host->generic_phy;
+	enum phy_mode mode;
 	int ret;
 
+	/*
+	 * HW ver 5 can only support up to HS-G5 Rate-A due to HW limitations.
+	 * If the HS-G5 PHY gear is used, update host_params->hs_rate to Rate-A,
+	 * so that the subsequent power mode change shall stick to Rate-A.
+	 */
+	if (host->hw_ver.major == 0x5) {
+		if (host->phy_gear == UFS_HS_G5)
+			host_params->hs_rate = PA_HS_MODE_A;
+		else
+			host_params->hs_rate = PA_HS_MODE_B;
+	}
+
+	mode = host_params->hs_rate == PA_HS_MODE_B ? PHY_MODE_UFS_HS_B : PHY_MODE_UFS_HS_A;
+
 	/* Reset UFS Host Controller and PHY */
 	ret = ufs_qcom_host_reset(hba);
 	if (ret)
@@ -459,7 +475,7 @@  static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
 		return ret;
 	}
 
-	phy_set_mode_ext(phy, PHY_MODE_UFS_HS_B, host->phy_gear);
+	phy_set_mode_ext(phy, mode, host->phy_gear);
 
 	/* power on phy - start serdes and phy's power and clocks */
 	ret = phy_power_on(phy);