diff mbox

[1/3] arm64: dts: qcom: sdm845: Add USB-related nodes

Message ID 20180710220202.116404-2-dianders@chromium.org (mailing list archive)
State New, archived
Delegated to: Andy Gross
Headers show

Commit Message

Douglas Anderson July 10, 2018, 10:02 p.m. UTC
From: Manu Gautam <mgautam@codeaurora.org>

This adds nodes for USB and related PHYs.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[dianders: reworked quite a bit]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---

 arch/arm64/boot/dts/qcom/sdm845.dtsi | 189 +++++++++++++++++++++++++++
 1 file changed, 189 insertions(+)

Comments

Douglas Anderson July 12, 2018, 4:56 p.m. UTC | #1
Hi,

On Tue, Jul 10, 2018 at 3:02 PM, Douglas Anderson <dianders@chromium.org> wrote:
> From: Manu Gautam <mgautam@codeaurora.org>
>
> This adds nodes for USB and related PHYs.
>
> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
> [dianders: reworked quite a bit]
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
> ---
>
>  arch/arm64/boot/dts/qcom/sdm845.dtsi | 189 +++++++++++++++++++++++++++
>  1 file changed, 189 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index 15188d34a2ab..1de59a39f4fa 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -8,6 +8,7 @@
>  #include <dt-bindings/clock/qcom,gcc-sdm845.h>
>  #include <dt-bindings/clock/qcom,rpmh.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/phy/phy-qcom-qusb2.h>
>  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>
>  / {
> @@ -249,6 +250,18 @@
>                         #power-domain-cells = <1>;
>                 };
>
> +               qfprom@780000 {
> +                       compatible = "qcom,qfprom";
> +                       reg = <0x780000 0x8ff>;

I have later found that this should point to the "corrected" address
range, not the raw one.  Thus address should be 0x784000.

...still trying to get more details on the exact right length.


> +                       #address-cells = <1>;
> +                       #size-cells = <1>;
> +
> +                       qusb2p_hstx_trim: hstx-trim@1eb {
> +                               reg = <0x1eb 0x1>;
> +                               bits = <1 4>;
> +                       };

I've now found out the trim location for the secondary port.  Thus on
my next revision I'll add:

qusb2s_hstx_trim: hstx-trim-secondary@1eb {
  reg = <0x1eb 0x2>;
  bits = <6 4>;
};

Since this series isn't really ready for merging yet (see the cover
letter), I'll sit on these changes for now but I'll include them in
the next spin.


-Doug
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index 15188d34a2ab..1de59a39f4fa 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -8,6 +8,7 @@ 
 #include <dt-bindings/clock/qcom,gcc-sdm845.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy-qcom-qusb2.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 
 / {
@@ -249,6 +250,18 @@ 
 			#power-domain-cells = <1>;
 		};
 
+		qfprom@780000 {
+			compatible = "qcom,qfprom";
+			reg = <0x780000 0x8ff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qusb2p_hstx_trim: hstx-trim@1eb {
+				reg = <0x1eb 0x1>;
+				bits = <1 4>;
+			};
+		};
+
 		qupv3_id_0: geniqup@8c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0x8c0000 0x6000>;
@@ -961,6 +974,182 @@ 
 			};
 		};
 
+		usb_1_hsphy: phy@88e2000 {
+			compatible = "qcom,sdm845-qusb2-phy";
+			reg = <0x88e2000 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+			nvmem-cells = <&qusb2p_hstx_trim>;
+		};
+
+		usb_2_hsphy: phy@88e3000 {
+			compatible = "qcom,sdm845-qusb2-phy";
+			reg = <0x88e3000 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+		};
+
+		usb_1_qmpphy: phy@88e9000 {
+			compatible = "qcom,sdm845-qmp-usb3-phy";
+			reg = <0x88e9000 0x18c>,
+			      <0x88e8000 0x10>;
+			reg-names = "reg-base", "dp_com";
+			status = "disabled";
+			#clock-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			usb_1_ssphy: lane@88e9200 {
+				reg = <0x88e9200 0x128>,
+				      <0x88e9400 0x200>,
+				      <0x88e9c00 0x218>,
+				      <0x88e9a00 0x100>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+		};
+
+		usb_2_qmpphy: phy@88eb000 {
+			compatible = "qcom,sdm845-qmp-usb3-uni-phy";
+			reg = <0x88eb000 0x18c>;
+			status = "disabled";
+			#clock-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_SEC_CLKREF_CLK>,
+				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+				 <&gcc GCC_USB3_PHY_SEC_BCR>;
+			reset-names = "phy", "common";
+
+			usb_2_ssphy: lane@88eb200 {
+				reg = <0x88eb200 0x128>,
+				      <0x88eb400 0x1fc>,
+				      <0x88eb800 0x218>,
+				      <0x88e9600 0x70>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_uni_phy_pipe_clk_src";
+			};
+		};
+
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
+			reg = <0xa6f8800 0x400>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <150000000>;
+
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq",
+					  "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			usb_1_dwc3: dwc3@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0xa600000 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		usb_2: usb@a8f8800 {
+			compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
+			reg = <0xa8f8800 0x400>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_SEC_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep";
+
+			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <150000000>;
+
+			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq",
+					  "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_SEC_GDSC>;
+
+			resets = <&gcc GCC_USB30_SEC_BCR>;
+
+			usb_2_dwc3: dwc3@a800000 {
+				compatible = "snps,dwc3";
+				reg = <0xa800000 0xcd00>;
+				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_2_hsphy>, <&usb_2_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
 		spmi_bus: spmi@c440000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0xc440000 0x1100>,