@@ -21,6 +21,7 @@
/* UART specific GENI registers */
#define SE_UART_LOOPBACK_CFG 0x22c
+#define SE_UART_IO_MACRO_CTRL 0x240
#define SE_UART_TX_TRANS_CFG 0x25c
#define SE_UART_TX_WORD_LEN 0x268
#define SE_UART_TX_STOP_BIT_LEN 0x26c
@@ -95,6 +96,12 @@
#define CTS_RTS_SORTED BIT(1)
#define RX_TX_CTS_RTS_SORTED (RX_TX_SORTED | CTS_RTS_SORTED)
+/* UART pin swap value */
+#define DEFAULT_IO_MACRO_IO0_IO1_MASK GENMASK(3, 0)
+#define IO_MACRO_IO0_SEL 0x3
+#define DEFAULT_IO_MACRO_IO2_IO3_MASK GENMASK(15, 4)
+#define IO_MACRO_IO2_IO3_SWAP 0x4640
+
#ifdef CONFIG_CONSOLE_POLL
#define CONSOLE_RX_BYTES_PW 1
#else
@@ -119,6 +126,8 @@ struct qcom_geni_serial_port {
unsigned int tx_remaining;
int wakeup_irq;
+ bool rx_tx_swap;
+ bool cts_rts_swap;
};
static const struct uart_ops qcom_geni_console_pops;
@@ -826,6 +835,7 @@ static int qcom_geni_serial_port_setup(struct uart_port *uport)
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
u32 rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT;
u32 proto;
+ u32 pin_swap;
if (uart_console(uport)) {
port->tx_bytes_pw = 1;
@@ -846,6 +856,20 @@ static int qcom_geni_serial_port_setup(struct uart_port *uport)
get_tx_fifo_size(port);
writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
+
+ pin_swap = readl(uport->membase + SE_UART_IO_MACRO_CTRL);
+ if (port->rx_tx_swap) {
+ pin_swap &= ~DEFAULT_IO_MACRO_IO2_IO3_MASK;
+ pin_swap |= IO_MACRO_IO2_IO3_SWAP;
+ }
+ if (port->cts_rts_swap) {
+ pin_swap &= ~DEFAULT_IO_MACRO_IO0_IO1_MASK;
+ pin_swap |= IO_MACRO_IO0_SEL;
+ }
+ /* Configure this register if RX-TX, CTS-RTS pins are swapped */
+ if (port->rx_tx_swap || port->cts_rts_swap)
+ writel(pin_swap, uport->membase + SE_UART_IO_MACRO_CTRL);
+
/*
* Make an unconditional cancel on the main sequencer to reset
* it else we could end up in data loss scenarios.
@@ -1289,6 +1313,12 @@ static int qcom_geni_serial_probe(struct platform_device *pdev)
if (!console)
port->wakeup_irq = platform_get_irq_optional(pdev, 1);
+ if (of_property_read_bool(pdev->dev.of_node, "rx-tx-swap"))
+ port->rx_tx_swap = true;
+
+ if (of_property_read_bool(pdev->dev.of_node, "cts-rts-swap"))
+ port->cts_rts_swap = true;
+
uport->private_data = drv;
platform_set_drvdata(pdev, port);
port->handle_rx = console ? handle_rx_console : handle_rx_uart;
Add capability to support RX-TX, CTS-RTS pins swap in HW. Configure UART_IO_MACRO_CTRL register accordingly if RX-TX pair or CTS-RTS pair or both pairs swapped. Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org> --- Changes in V2: - As per Greg's comment removed the change id. Changes in V3: - As per Bjorn's comment using of_property_read_bool() to read dtsi entries. - As per Matthias's comment add capability to support individual pairs swap, that is, only RX-TX swap and only CTS-RTS swap cases. Changes in V4: - As per Matthias's comment changed IO_MACRO_IO0_SEL definition. drivers/tty/serial/qcom_geni_serial.c | 30 +++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)