@@ -32,9 +32,28 @@ enum spm_reg {
SPM_REG_SEQ_ENTRY,
SPM_REG_SPM_STS,
SPM_REG_PMIC_STS,
+ SPM_REG_AVS_CTL,
+ SPM_REG_AVS_LIMIT,
SPM_REG_NR,
};
+static const u16 spm_reg_offset_v4_1[SPM_REG_NR] = {
+ [SPM_REG_AVS_CTL] = 0x904,
+ [SPM_REG_AVS_LIMIT] = 0x908,
+};
+
+static const struct spm_reg_data spm_reg_660_gold_l2 = {
+ .reg_offset = spm_reg_offset_v4_1,
+ .avs_ctl = 0x1010031,
+ .avs_limit = 0x4580458,
+};
+
+static const struct spm_reg_data spm_reg_660_silver_l2 = {
+ .reg_offset = spm_reg_offset_v4_1,
+ .avs_ctl = 0x101c031,
+ .avs_limit = 0x4580458,
+};
+
static const u16 spm_reg_offset_v2_1[SPM_REG_NR] = {
[SPM_REG_CFG] = 0x08,
[SPM_REG_SPM_CTL] = 0x30,
@@ -126,6 +145,10 @@ void spm_set_low_power_mode(struct spm_driver_data *drv,
}
static const struct of_device_id spm_match_table[] = {
+ { .compatible = "qcom,sdm660-gold-saw2-v4.1-l2",
+ .data = &spm_reg_660_gold_l2 },
+ { .compatible = "qcom,sdm660-silver-saw2-v4.1-l2",
+ .data = &spm_reg_660_silver_l2 },
{ .compatible = "qcom,msm8974-saw2-v2.1-cpu",
.data = &spm_reg_8974_8084_cpu },
{ .compatible = "qcom,apq8084-saw2-v2.1-cpu",
@@ -169,6 +192,8 @@ static int spm_dev_probe(struct platform_device *pdev)
* CPU was held in reset, the reset signal could trigger the SPM state
* machine, before the sequences are completely written.
*/
+ spm_register_write(drv, SPM_REG_AVS_CTL, drv->reg_data->avs_ctl);
+ spm_register_write(drv, SPM_REG_AVS_LIMIT, drv->reg_data->avs_limit);
spm_register_write(drv, SPM_REG_CFG, drv->reg_data->spm_cfg);
spm_register_write(drv, SPM_REG_DLY, drv->reg_data->spm_dly);
spm_register_write(drv, SPM_REG_PMIC_DLY, drv->reg_data->pmic_dly);
@@ -178,7 +203,8 @@ static int spm_dev_probe(struct platform_device *pdev)
drv->reg_data->pmic_data[1]);
/* Set up Standby as the default low power mode */
- spm_set_low_power_mode(drv, PM_SLEEP_MODE_STBY);
+ if (drv->reg_data->reg_offset[SPM_REG_SPM_CTL])
+ spm_set_low_power_mode(drv, PM_SLEEP_MODE_STBY);
return 0;
}
Implement the support for SAW v4.1, used in at least MSM8998, SDM630, SDM660 and APQ variants and, while at it, also add the configuration for the SDM630/660 Silver and Gold cluster L2 Adaptive Voltage Scaler: this is also one of the prerequisites to allow the OSM controller to perform DCVS. Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> --- drivers/soc/qcom/spm.c | 28 +++++++++++++++++++++++++++- 1 file changed, 27 insertions(+), 1 deletion(-)