[11/15] ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB

Message ID	20210408170457.91409-12-manivannan.sadhasivam@linaro.org (mailing list archive)
State	Accepted
Headers	show Return-Path: <linux-arm-msm-owner@kernel.org> From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> To: bjorn.andersson@linaro.org Cc: linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org, Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Subject: [PATCH 11/15] ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB Date: Thu, 8 Apr 2021 22:34:53 +0530 Message-Id: <20210408170457.91409-12-manivannan.sadhasivam@linaro.org> In-Reply-To: <20210408170457.91409-1-manivannan.sadhasivam@linaro.org> References: <20210408170457.91409-1-manivannan.sadhasivam@linaro.org> MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Precedence: bulk
Series	SDX55 devicetree updates \| expand [00/15] SDX55 devicetree updates [01/15] ARM: dts: qcom: sdx55: Add support for A7 PLL clock [02/15] ARM: dts: qcom: sdx55: Add support for APCS block [03/15] ARM: dts: qcom: sdx55: Add CPUFreq support [04/15] ARM: dts: qcom: sdx55: Add modem SMP2P node [05/15] ARM: dts: qcom: sdx55: Add IMEM and PIL info region [06/15] dt-bindings: firmware: scm: Add compatible for SDX55 [07/15] ARM: dts: qcom: sdx55: Add SCM node [08/15] ARM: dts: qcom: sdx55: Add interconnect nodes [09/15] ARM: dts: qcom: Fix node name for NAND controller node [10/15] dt-bindings: arm: qcom: Add binding for Telit FN980 TLB board [11/15] ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB [12/15] dt-bindings: arm: qcom: Add binding for Thundercomm T55 kit [13/15] ARM: dts: qcom: sdx55: Add basic devicetree support for Thundercomm T55 [14/15] dt-bindings: remoteproc: qcom: pas: Add binding for SDX55 [15/15] ARM: dts: qcom: sdx55: Add Modem remoteproc node

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 8e5d4ab4e75e..874ab2b66187 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -929,7 +929,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-msm8974-sony-xperia-castor.dtb \ qcom-msm8974-sony-xperia-honami.dtb \ qcom-mdm9615-wp8548-mangoh-green.dtb \ - qcom-sdx55-mtp.dtb + qcom-sdx55-mtp.dtb \ + qcom-sdx55-telit-fn980-tlb.dtb dtb-$(CONFIG_ARCH_RDA) += \ rda8810pl-orangepi-2g-iot.dtb \ rda8810pl-orangepi-i96.dtb diff --git a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts new file mode 100644 index 000000000000..6da366ec15b3 --- /dev/null +++ b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts @@ -0,0 +1,277 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Ltd. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "qcom-sdx55.dtsi" +#include "qcom-pmx55.dtsi" + +/ { + model = "Telit FN980 TLB"; + compatible = "qcom,sdx55-telit-fn980-tlb", "qcom,sdx55"; + qcom,board-id = <0xb010008 0x0>; + + aliases { + serial0 = &blsp1_uart3; + }; + + chosen { + stdout-path = "serial0:921600n8"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mpss_debug_mem: memory@8ef00000 { + no-map; + reg = <0x8ef00000 0x800000>; + }; + + ipa_fw_mem: memory@8fced000 { + no-map; + reg = <0x8fced000 0x10000>; + }; + + mpss_adsp_mem: memory@90800000 { + no-map; + reg = <0x90800000 0xf800000>; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + vreg_bob_3p3: pmx55-bob { + compatible = "regulator-fixed"; + regulator-name = "vreg_bob_3p3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; + + vreg_s7e_mx_0p752: pmx55-s7e { + compatible = "regulator-fixed"; + regulator-name = "vreg_s7e_mx_0p752"; + regulator-min-microvolt = <752000>; + regulator-max-microvolt = <752000>; + + vin-supply = <&vph_pwr>; + }; + + vreg_sd_vdd: sd-vdd { + compatible = "regulator-fixed"; + regulator-name = "vreg_sd_vdd"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + + vin-supply = <&vreg_vddpx_2>; + }; + + vreg_vddpx_2: vddpx-2 { + compatible = "regulator-gpio"; + regulator-name = "vreg_vddpx_2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2850000>; + enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>; + gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>; + states = <1800000 0>, <2850000 1>; + startup-delay-us = <200000>; + enable-active-high; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; +}; + +&apps_rsc { + pmx55-rpmh-regulators { + compatible = "qcom,pmx55-rpmh-regulators"; + qcom,pmic-id = "e"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-l1-l2-supply = <&vreg_s2e_1p224>; + vdd-l3-l9-supply = <&vreg_s3e_0p824>; + vdd-l4-l12-supply = <&vreg_s4e_1p904>; + vdd-l5-l6-supply = <&vreg_s4e_1p904>; + vdd-l7-l8-supply = <&vreg_s3e_0p824>; + vdd-l10-l11-l13-supply = <&vreg_bob_3p3>; + vdd-l14-supply = <&vreg_s7e_mx_0p752>; + vdd-l15-supply = <&vreg_s2e_1p224>; + vdd-l16-supply = <&vreg_s4e_1p904>; + + vreg_s2e_1p224: smps2 { + regulator-min-microvolt = <1280000>; + regulator-max-microvolt = <1400000>; + }; + + vreg_s3e_0p824: smps3 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_s4e_1p904: smps4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1960000>; + }; + + vreg_l1e_bb_1p2: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo2 { + regulator-min-microvolt = <1128000>; + regulator-max-microvolt = <1128000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo3 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l4e_bb_0p875: ldo4 { + regulator-min-microvolt = <872000>; + regulator-max-microvolt = <872000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l5e_bb_1p7: ldo5 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo7 { + regulator-min-microvolt = <480000>; + regulator-max-microvolt = <900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo8 { + regulator-min-microvolt = <480000>; + regulator-max-microvolt = <900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo9 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l10e_3p1: ldo10 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo11 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo12 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo13 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo14 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo15 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + ldo16 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + }; +}; + +&blsp1_uart3 { + status = "ok"; +}; + +&qpic_bam { + status = "ok"; +}; + +&qpic_nand { + status = "ok"; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + /* ico and efs2 partitions are secured */ + secure-regions = <0x500000 0x500000 + 0xa00000 0xb00000>; + }; +}; + +&usb_hsphy { + status = "okay"; + vdda-pll-supply = <&vreg_l4e_bb_0p875>; + vdda33-supply = <&vreg_l10e_3p1>; + vdda18-supply = <&vreg_l5e_bb_1p7>; +}; + +&usb_qmpphy { + status = "okay"; + vdda-phy-supply = <&vreg_l4e_bb_0p875>; + vdda-pll-supply = <&vreg_l1e_bb_1p2>; +}; + +&usb { + status = "okay"; +}; + +&usb_dwc3 { + dr_mode = "peripheral"; +};

[11/15] ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB

Commit Message

Patch