| Message ID | 20210514104328.18756-1-stephan@gerhold.net (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
| Series | [1/5] arm64: dts: qcom: msm8916: Add device tree for Huawei Ascend G7 | expand |
On Fri 14 May 05:43 CDT 2021, Stephan Gerhold wrote: > The Huawei Ascend G7 is a smartphone from Huawei based on MSM8916. > It's fairly similar to the other MSM8916 devices, the only notable > exception are the "cd-gpios" for detecting if a SD card was inserted: > It looks like Huawei forgot to re-route this to gpio38, so the correct > GPIO seems to be gpio56 on this device. > > Note: The original firmware from Huawei can only boot 32-bit kernels. > To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware > with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei > forgot to set up (firmware) secure boot for some reason. > > Also note that Huawei no longer provides bootloader unlock codes. > This can be bypassed by patching the bootloader from a custom HYP firmware, > making it think the bootloader is unlocked. I use a modified version of > qhypstub [1], that patches a single instruction in the Huawei bootloader. > > The device tree contains initial support for the Huawei Ascend G7 with: > - UART (untested, probably available via some test points) > - eMMC/SD card > - Buttons > - Notification LED (combination of 3 GPIO LEDs) > - Vibrator > - WiFi/Bluetooth (WCNSS) > - USB > > [1]: https://github.com/msm8916-mainline/qhypstub > > Signed-off-by: Stephan Gerhold <stephan@gerhold.net> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../arm64/boot/dts/qcom/msm8916-huawei-g7.dts | 279 ++++++++++++++++++ > 2 files changed, 280 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 456502aeee49..c894de19654e 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8916-huawei-g7.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts > new file mode 100644 > index 000000000000..d67aa7dd4a21 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts > @@ -0,0 +1,279 @@ > +// SPDX-License-Identifier: GPL-2.0-only Would it be possible to change this to BSD license instead? Apart from that, the patches looks really good. Thanks, Bjorn > +// Copyright (C) 2021 Stephan Gerhold > + > +/dts-v1/; > + > +#include "msm8916-pm8916.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > + > +/* > + * Note: The original firmware from Huawei can only boot 32-bit kernels. > + * To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware > + * with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei > + * forgot to set up (firmware) secure boot for some reason. > + * > + * Also note that Huawei no longer provides bootloader unlock codes. > + * This can be bypassed by patching the bootloader from a custom HYP firmware, > + * making it think the bootloader is unlocked. > + * > + * See: https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7) > + */ > + > +/ { > + model = "Huawei Ascend G7"; > + compatible = "huawei,g7", "qcom,msm8916"; > + > + aliases { > + serial0 = &blsp1_uart2; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_keys_default>; > + > + label = "GPIO Buttons"; > + > + volume-up { > + label = "Volume Up"; > + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_leds_default>; > + > + led-0 { > + gpios = <&msmgpio 8 GPIO_ACTIVE_HIGH>; > + color = <LED_COLOR_ID_RED>; > + default-state = "off"; > + function = LED_FUNCTION_INDICATOR; > + }; > + > + led-1 { > + gpios = <&msmgpio 9 GPIO_ACTIVE_HIGH>; > + color = <LED_COLOR_ID_GREEN>; > + default-state = "off"; > + function = LED_FUNCTION_INDICATOR; > + }; > + > + led-2 { > + gpios = <&msmgpio 10 GPIO_ACTIVE_HIGH>; > + color = <LED_COLOR_ID_BLUE>; > + default-state = "off"; > + function = LED_FUNCTION_INDICATOR; > + }; > + }; > + > + usb_id: usb-id { > + compatible = "linux,extcon-usb-gpio"; > + id-gpio = <&msmgpio 117 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&usb_id_default>; > + }; > +}; > + > +&blsp1_uart2 { > + status = "okay"; > +}; > + > +&pm8916_resin { > + status = "okay"; > + linux,code = <KEY_VOLUMEDOWN>; > +}; > + > +&pm8916_vib { > + status = "okay"; > +}; > + > +&pronto { > + status = "okay"; > +}; > + > +&sdhc_1 { > + status = "okay"; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; > + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; > +}; > + > +&sdhc_2 { > + status = "okay"; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdhc2_cd_default>; > + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdhc2_cd_default>; > + > + /* > + * The Huawei device tree sets cd-gpios = <&msmgpio 38 GPIO_ACTIVE_HIGH>. > + * However, gpio38 does not change its state when inserting/removing the > + * SD card, it's just low all the time. The Huawei kernel seems to use > + * polling for SD card detection instead. > + * > + * However, looking closer at the GPIO debug output it turns out that > + * gpio56 switches its state when inserting/removing the SD card. > + * It behaves just like gpio38 normally does. Usually GPIO56 is used as > + * "UIM2_PRESENT", i.e. to check if a second SIM card is inserted. > + * Maybe Huawei decided to replace the second SIM card slot with the > + * SD card slot and forgot to re-route to gpio38. > + */ > + cd-gpios = <&msmgpio 56 GPIO_ACTIVE_LOW>; > +}; > + > +&usb { > + status = "okay"; > + extcon = <&usb_id>, <&usb_id>; > +}; > + > +&usb_hs_phy { > + extcon = <&usb_id>; > +}; > + > +&smd_rpm_regulators { > + vdd_l1_l2_l3-supply = <&pm8916_s3>; > + vdd_l4_l5_l6-supply = <&pm8916_s4>; > + vdd_l7-supply = <&pm8916_s4>; > + > + s3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + }; > + > + s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + l1 { > + regulator-min-microvolt = <1225000>; > + regulator-max-microvolt = <1225000>; > + }; > + > + l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + l4 { > + regulator-min-microvolt = <2050000>; > + regulator-max-microvolt = <2050000>; > + }; > + > + l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l8 { > + regulator-min-microvolt = <2950000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + l9 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l10 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + l11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + regulator-allow-set-load; > + regulator-system-load = <200000>; > + }; > + > + l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + l13 { > + regulator-min-microvolt = <3075000>; > + regulator-max-microvolt = <3075000>; > + }; > + > + l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l16 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + l18 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2700000>; > + }; > +}; > + > +&msmgpio { > + gpio_keys_default: gpio-keys-default { > + pins = "gpio107"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + gpio_leds_default: gpio-leds-default { > + pins = "gpio8", "gpio9", "gpio10"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + sdhc2_cd_default: sdhc2-cd-default { > + pins = "gpio56"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-disable; > + }; > + > + usb_id_default: usb-id-default { > + pins = "gpio117"; > + function = "gpio"; > + > + drive-strength = <8>; > + bias-pull-up; > + }; > +}; > -- > 2.31.1 >
On Thu, Jun 10, 2021 at 10:32:50AM -0500, Bjorn Andersson wrote: > On Fri 14 May 05:43 CDT 2021, Stephan Gerhold wrote: > > > The Huawei Ascend G7 is a smartphone from Huawei based on MSM8916. > > It's fairly similar to the other MSM8916 devices, the only notable > > exception are the "cd-gpios" for detecting if a SD card was inserted: > > It looks like Huawei forgot to re-route this to gpio38, so the correct > > GPIO seems to be gpio56 on this device. > > > > Note: The original firmware from Huawei can only boot 32-bit kernels. > > To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware > > with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei > > forgot to set up (firmware) secure boot for some reason. > > > > Also note that Huawei no longer provides bootloader unlock codes. > > This can be bypassed by patching the bootloader from a custom HYP firmware, > > making it think the bootloader is unlocked. I use a modified version of > > qhypstub [1], that patches a single instruction in the Huawei bootloader. > > > > The device tree contains initial support for the Huawei Ascend G7 with: > > - UART (untested, probably available via some test points) > > - eMMC/SD card > > - Buttons > > - Notification LED (combination of 3 GPIO LEDs) > > - Vibrator > > - WiFi/Bluetooth (WCNSS) > > - USB > > > > [1]: https://github.com/msm8916-mainline/qhypstub > > > > Signed-off-by: Stephan Gerhold <stephan@gerhold.net> > > --- > > arch/arm64/boot/dts/qcom/Makefile | 1 + > > .../arm64/boot/dts/qcom/msm8916-huawei-g7.dts | 279 ++++++++++++++++++ > > 2 files changed, 280 insertions(+) > > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts > > > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > > index 456502aeee49..c894de19654e 100644 > > --- a/arch/arm64/boot/dts/qcom/Makefile > > +++ b/arch/arm64/boot/dts/qcom/Makefile > > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb > > dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb > > dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb > > +dtb-$(CONFIG_ARCH_QCOM) += msm8916-huawei-g7.dtb > > dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb > > dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb > > dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb > > diff --git a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts > > new file mode 100644 > > index 000000000000..d67aa7dd4a21 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts > > @@ -0,0 +1,279 @@ > > +// SPDX-License-Identifier: GPL-2.0-only > > Would it be possible to change this to BSD license instead? > Sorry, I'm not sure I can. :/ This is derived from the other MSM8916 device trees that are GPL-2.0-only, which are again derived from work that was made by many other people. I'm not sure I can just put BSD here. Also, would this really change anything? All the common MSM8916 includes (msm8916.dtsi, pm8916.dtsi etc) are GPL-2.0-only so the resulting device tree will forever stay GPL-2.0-only anyway. I think we can only properly apply BSD to new device trees (unless we could somehow get permission from all previous contributors). Personally I would rather have the license consistent for all devices based on one SoC, everything else will just be confusing for someone who looks only at this particular file and mistakenly assumes it's completely available under BSD. Thanks, Stephan
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 456502aeee49..c894de19654e 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-huawei-g7.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts new file mode 100644 index 000000000000..d67aa7dd4a21 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts @@ -0,0 +1,279 @@ +// SPDX-License-Identifier: GPL-2.0-only +// Copyright (C) 2021 Stephan Gerhold + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> + +/* + * Note: The original firmware from Huawei can only boot 32-bit kernels. + * To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware + * with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei + * forgot to set up (firmware) secure boot for some reason. + * + * Also note that Huawei no longer provides bootloader unlock codes. + * This can be bypassed by patching the bootloader from a custom HYP firmware, + * making it think the bootloader is unlocked. + * + * See: https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7) + */ + +/ { + model = "Huawei Ascend G7"; + compatible = "huawei,g7", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_leds_default>; + + led-0 { + gpios = <&msmgpio 8 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_RED>; + default-state = "off"; + function = LED_FUNCTION_INDICATOR; + }; + + led-1 { + gpios = <&msmgpio 9 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_GREEN>; + default-state = "off"; + function = LED_FUNCTION_INDICATOR; + }; + + led-2 { + gpios = <&msmgpio 10 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_BLUE>; + default-state = "off"; + function = LED_FUNCTION_INDICATOR; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 117 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&pm8916_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&pm8916_vib { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdhc2_cd_default>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdhc2_cd_default>; + + /* + * The Huawei device tree sets cd-gpios = <&msmgpio 38 GPIO_ACTIVE_HIGH>. + * However, gpio38 does not change its state when inserting/removing the + * SD card, it's just low all the time. The Huawei kernel seems to use + * polling for SD card detection instead. + * + * However, looking closer at the GPIO debug output it turns out that + * gpio56 switches its state when inserting/removing the SD card. + * It behaves just like gpio38 normally does. Usually GPIO56 is used as + * "UIM2_PRESENT", i.e. to check if a second SIM card is inserted. + * Maybe Huawei decided to replace the second SIM card slot with the + * SD card slot and forgot to re-route to gpio38. + */ + cd-gpios = <&msmgpio 56 GPIO_ACTIVE_LOW>; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + gpio_keys_default: gpio-keys-default { + pins = "gpio107"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + gpio_leds_default: gpio-leds-default { + pins = "gpio8", "gpio9", "gpio10"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + sdhc2_cd_default: sdhc2-cd-default { + pins = "gpio56"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + usb_id_default: usb-id-default { + pins = "gpio117"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +};
The Huawei Ascend G7 is a smartphone from Huawei based on MSM8916. It's fairly similar to the other MSM8916 devices, the only notable exception are the "cd-gpios" for detecting if a SD card was inserted: It looks like Huawei forgot to re-route this to gpio38, so the correct GPIO seems to be gpio56 on this device. Note: The original firmware from Huawei can only boot 32-bit kernels. To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei forgot to set up (firmware) secure boot for some reason. Also note that Huawei no longer provides bootloader unlock codes. This can be bypassed by patching the bootloader from a custom HYP firmware, making it think the bootloader is unlocked. I use a modified version of qhypstub [1], that patches a single instruction in the Huawei bootloader. The device tree contains initial support for the Huawei Ascend G7 with: - UART (untested, probably available via some test points) - eMMC/SD card - Buttons - Notification LED (combination of 3 GPIO LEDs) - Vibrator - WiFi/Bluetooth (WCNSS) - USB [1]: https://github.com/msm8916-mainline/qhypstub Signed-off-by: Stephan Gerhold <stephan@gerhold.net> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../arm64/boot/dts/qcom/msm8916-huawei-g7.dts | 279 ++++++++++++++++++ 2 files changed, 280 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts