deleted file mode 100644
@@ -1,157 +0,0 @@
-Qualcomm adreno/snapdragon GPU
-
-Required properties:
-- compatible: "qcom,adreno-XYZ.W", "qcom,adreno" or
- "amd,imageon-XYZ.W", "amd,imageon"
- for example: "qcom,adreno-306.0", "qcom,adreno"
- Note that you need to list the less specific "qcom,adreno" (since this
- is what the device is matched on), in addition to the more specific
- with the chip-id.
- If "amd,imageon" is used, there should be no top level msm device.
-- reg: Physical base address and length of the controller's registers.
-- interrupts: The interrupt signal from the gpu.
-- clocks: device clocks (if applicable)
- See ../clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required by a3xx, a4xx and a5xx
- cores:
- * "core"
- * "iface"
- * "mem_iface"
- For GMU attached devices the GPU clocks are not used and are not required. The
- following devices should not list clocks:
- - qcom,adreno-630.2
-- iommus: optional phandle to an adreno iommu instance
-- operating-points-v2: optional phandle to the OPP operating points
-- interconnects: optional phandle to an interconnect provider. See
- ../interconnect/interconnect.txt for details. Some A3xx and all A4xx platforms
- will have two paths; all others will have one path.
-- interconnect-names: The names of the interconnect paths that correspond to the
- interconnects property. Values must be gfx-mem and ocmem.
-- qcom,gmu: For GMU attached devices a phandle to the GMU device that will
- control the power for the GPU. Applicable targets:
- - qcom,adreno-630.2
-- zap-shader: For a5xx and a6xx devices this node contains a memory-region that
- points to reserved memory to store the zap shader that can be used to help
- bring the GPU out of secure mode.
-- firmware-name: optional property of the 'zap-shader' node, listing the
- relative path of the device specific zap firmware.
-- sram: phandle to the On Chip Memory (OCMEM) that's present on some a3xx and
- a4xx Snapdragon SoCs. See
- Documentation/devicetree/bindings/sram/qcom,ocmem.yaml.
-
-Optional properties:
-- #cooling-cells: The value must be 2. For details, please refer
- Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml.
-
-Example 3xx/4xx:
-
-/ {
- ...
-
- gpu: adreno@fdb00000 {
- compatible = "qcom,adreno-330.2",
- "qcom,adreno";
- reg = <0xfdb00000 0x10000>;
- reg-names = "kgsl_3d0_reg_memory";
- interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "kgsl_3d0_irq";
- clock-names = "core",
- "iface",
- "mem_iface";
- clocks = <&mmcc OXILI_GFX3D_CLK>,
- <&mmcc OXILICX_AHB_CLK>,
- <&mmcc OXILICX_AXI_CLK>;
- sram = <&gpu_sram>;
- power-domains = <&mmcc OXILICX_GDSC>;
- operating-points-v2 = <&gpu_opp_table>;
- iommus = <&gpu_iommu 0>;
- #cooling-cells = <2>;
- };
-
- gpu_sram: ocmem@fdd00000 {
- compatible = "qcom,msm8974-ocmem";
-
- reg = <0xfdd00000 0x2000>,
- <0xfec00000 0x180000>;
- reg-names = "ctrl",
- "mem";
-
- clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
- <&mmcc OCMEMCX_OCMEMNOC_CLK>;
- clock-names = "core",
- "iface";
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- gpu_sram: gpu-sram@0 {
- reg = <0x0 0x100000>;
- ranges = <0 0 0xfec00000 0x100000>;
- };
- };
-};
-
-Example a6xx (with GMU):
-
-/ {
- ...
-
- gpu@5000000 {
- compatible = "qcom,adreno-630.2", "qcom,adreno";
- #stream-id-cells = <16>;
-
- reg = <0x5000000 0x40000>, <0x509e000 0x10>;
- reg-names = "kgsl_3d0_reg_memory", "cx_mem";
-
- #cooling-cells = <2>;
-
- /*
- * Look ma, no clocks! The GPU clocks and power are
- * controlled entirely by the GMU
- */
-
- interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
-
- iommus = <&adreno_smmu 0>;
-
- operating-points-v2 = <&gpu_opp_table>;
-
- interconnects = <&rsc_hlos MASTER_GFX3D &rsc_hlos SLAVE_EBI1>;
- interconnect-names = "gfx-mem";
-
- gpu_opp_table: opp-table {
- compatible = "operating-points-v2";
-
- opp-430000000 {
- opp-hz = /bits/ 64 <430000000>;
- opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
- opp-peak-kBps = <5412000>;
- };
-
- opp-355000000 {
- opp-hz = /bits/ 64 <355000000>;
- opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
- opp-peak-kBps = <3072000>;
- };
-
- opp-267000000 {
- opp-hz = /bits/ 64 <267000000>;
- opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
- opp-peak-kBps = <3072000>;
- };
-
- opp-180000000 {
- opp-hz = /bits/ 64 <180000000>;
- opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
- opp-peak-kBps = <1804000>;
- };
- };
-
- qcom,gmu = <&gmu>;
-
- zap-shader {
- memory-region = <&zap_shader_region>;
- firmware-name = "qcom/LENOVO/81JL/qcdxkmsuc850.mbn"
- };
- };
-};
new file mode 100644
@@ -0,0 +1,297 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+
+$id: "http://devicetree.org/schemas/display/msm/gpu.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Devicetree bindings for the Adreno or Snapdragon GPUs
+
+maintainers:
+ - Rob Clark <robdclark@gmail.com>
+
+properties:
+ compatible:
+ oneOf:
+ - description: |
+ The driver is parsing the compat string for Adreno to figure out the gpu-id and patch level.
+ items:
+ - pattern: '^qcom,adreno-[3-6][0-9][0-9]\.[0-9]$'
+ - const: qcom,adreno
+ - description: |
+ The driver is parsing the compat string for Imageon to figure out the gpu-id and patch level.
+ items:
+ - pattern: '^amd,imageon-200\.[0-1]$'
+ - const: amd,imageon
+
+ clocks:
+ description: Requirements depends on the Adreno gpu-id.
+
+ clock-names:
+ description: Requirements depends on the Adreno gpu-id.
+
+ reg:
+ minItems: 1
+ maxItems: 3
+
+ reg-names:
+ minItems: 1
+ maxItems: 3
+ items:
+ enum:
+ - kgsl_3d0_reg_memory
+ - cx_mem
+ - cx_dbgc
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-names:
+ maxItems: 1
+
+ interconnects:
+ minItems: 1
+ maxItems: 2
+ description: |
+ Optional phandle to an interconnect provider. See
+ ../interconnect/interconnect.txt for details.
+ Some A3xx and all A4xx platforms will have two paths;
+ all others will have one path.
+
+ interconnect-names:
+ minItems: 1
+ maxItems: 2
+ items:
+ enum:
+ - gfx-mem
+ - ocmem
+ description: |
+ the names of the interconnect paths that correspond to
+ the interconnects property
+
+ iommus:
+ maxItems: 1
+
+ sram:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ minItems: 1
+ maxItems: 4
+ description: |
+ phandles to one or more reserved on-chip SRAM regions.
+ phandle to the On Chip Memory (OCMEM) that's present on some a3xx and
+ a4xx Snapdragon SoCs. See
+ Documentation/devicetree/bindings/sram/qcom,ocmem.yaml
+
+ operating-points-v2: true
+ opp-table: true
+
+ power-domains:
+ maxItems: 1
+
+ zap-shader:
+ type: object
+ description: |
+ For a5xx and a6xx devices this node contains a memory-region that
+ points to reserved memory to store the zap shader that can be used to
+ help bring the GPU out of secure mode.
+ properties:
+ memory-region:
+ $ref: /schemas/types.yaml#/definitions/phandle
+
+ firmware-name:
+ description: |
+ Default name of the firmware to load to the remote processor.
+ required:
+ - firmware-name
+
+ "#cooling-cells":
+ const: 2
+
+ qcom,gmu:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: |
+ For GMU attached devices a phandle to the GMU device that will
+ control the power for the GPU.
+
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+additionalProperties: false
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ pattern: '^qcom,adreno-[3-5][0-9][0-9]\.[0-9]$'
+
+ then:
+ properties:
+ clocks:
+ minItems: 2
+ maxItems: 7
+
+ clock-names:
+ items:
+ anyOf:
+ - const: core
+ description: GPU Core clock
+ - const: iface
+ description: GPU Interface clock
+ - const: mem
+ description: GPU Memory clock
+ - const: mem_iface
+ description: GPU Memory Interface clock
+ - const: alt_mem_iface
+ description: GPU Alternative Memory Interface clock
+ - const: gfx3d
+ description: GPU 3D engine clock
+ - const: rbbmtimer
+ description: GPU RBBM Timer for Adreno 5xx series
+ minItems: 2
+ maxItems: 7
+
+ required:
+ - clocks
+ - clock-names
+ - if:
+ properties:
+ compatible:
+ contains:
+ pattern: '^qcom,adreno-6[0-9][0-9]\.[0-9]$'
+
+ then: # Since Adreno 6xx series clocks should be defined in GMU
+ properties:
+ clocks:
+ maxItems: 0
+
+ clock-names:
+ maxItems: 0
+
+examples:
+ - |
+
+ // Example a3xx/4xx:
+
+ #include <dt-bindings/clock/qcom,mmcc-msm8974.h>
+ #include <dt-bindings/clock/qcom,rpmcc.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ gpu: gpu@fdb00000 {
+ compatible = "qcom,adreno-330.2", "qcom,adreno";
+
+ reg = <0xfdb00000 0x10000>;
+ reg-names = "kgsl_3d0_reg_memory";
+
+ clock-names = "core", "iface", "mem_iface";
+ clocks = <&mmcc OXILI_GFX3D_CLK>,
+ <&mmcc OXILICX_AHB_CLK>,
+ <&mmcc OXILICX_AXI_CLK>;
+
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "kgsl_3d0_irq";
+
+ sram = <&gpu_sram>;
+ power-domains = <&mmcc OXILICX_GDSC>;
+ operating-points-v2 = <&gpu_opp_table>;
+ iommus = <&gpu_iommu 0>;
+ #cooling-cells = <2>;
+ };
+
+ ocmem@fdd00000 {
+ compatible = "qcom,msm8974-ocmem";
+
+ reg = <0xfdd00000 0x2000>,
+ <0xfec00000 0x180000>;
+ reg-names = "ctrl", "mem";
+
+ clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
+ <&mmcc OCMEMCX_OCMEMNOC_CLK>;
+ clock-names = "core", "iface";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xfec00000 0x100000>;
+
+ gpu_sram: gpu-sram@0 {
+ reg = <0x0 0x100000>;
+ };
+ };
+ - |
+
+ // Example a6xx (with GMU):
+
+ #include <dt-bindings/clock/qcom,gpucc-sdm845.h>
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/power/qcom-rpmpd.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interconnect/qcom,sdm845.h>
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ zap_shader_region: gpu@8f200000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x90b00000 0x0 0xa00000>;
+ no-map;
+ };
+ };
+
+ gpu@5000000 {
+ compatible = "qcom,adreno-630.2", "qcom,adreno";
+
+ reg = <0x5000000 0x40000>, <0x509e000 0x10>;
+ reg-names = "kgsl_3d0_reg_memory", "cx_mem";
+
+ #cooling-cells = <2>;
+
+ interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+
+ iommus = <&adreno_smmu 0>;
+
+ operating-points-v2 = <&gpu_opp_table>;
+
+ interconnects = <&rsc_hlos MASTER_GFX3D &rsc_hlos SLAVE_EBI1>;
+ interconnect-names = "gfx-mem";
+
+ qcom,gmu = <&gmu>;
+
+ gpu_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-430000000 {
+ opp-hz = /bits/ 64 <430000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ opp-peak-kBps = <5412000>;
+ };
+
+ opp-355000000 {
+ opp-hz = /bits/ 64 <355000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+ opp-peak-kBps = <3072000>;
+ };
+
+ opp-267000000 {
+ opp-hz = /bits/ 64 <267000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ opp-peak-kBps = <3072000>;
+ };
+
+ opp-180000000 {
+ opp-hz = /bits/ 64 <180000000>;
+ opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ opp-peak-kBps = <1804000>;
+ };
+ };
+
+ zap-shader {
+ memory-region = <&zap_shader_region>;
+ firmware-name = "qcom/LENOVO/81JL/qcdxkmsuc850.mbn";
+ };
+ };
Signed-off-by: David Heidelberg <david@ixit.cz> --- v2: - added compatbile description from Rob Clark - dropped reg description - reg numbers increased to 3 (since we also have uncommon cx_dbgc) - specified interconnect-names items range - defined zap-shader as an object and added it's properties - enforce 0 clocks for Andreno >= 6xx since it's defined in GMU node v3: - fix patterns (add backslash before dot) - add aditional clocks - adreno@ -> gpu@ - add few const and change enum to anyOf - added clock & clock-names placeholder in non-conditional part (description) .../devicetree/bindings/display/msm/gpu.txt | 157 --------- .../devicetree/bindings/display/msm/gpu.yaml | 297 ++++++++++++++++++ 2 files changed, 297 insertions(+), 157 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/msm/gpu.txt create mode 100644 Documentation/devicetree/bindings/display/msm/gpu.yaml