diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 8398c0a2150f..eb1228f646cb 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -74,6 +74,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts
new file mode 100644
index 000000000000..7a92679a688b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Herobrine board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+#include "sc7280-herobrine.dtsi"
+
+/ {
+	model = "Google Herobrine";
+	compatible = "google,herobrine",
+		     "qcom,sc7280";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
new file mode 100644
index 000000000000..4619fa9fcacd
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -0,0 +1,1412 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Herobrine board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc7280.dtsi"
+
+/* PMICs depend on spmi_bus label and so must come after SoC */
+#include "pm7325.dtsi"
+#include "pm8350c.dtsi"
+#include "pmk8350.dtsi"
+
+/*
+ * Reserved memory changes
+ *
+ * Delete all unused memory nodes and define the peripheral memory regions
+ * required by the board dts.
+ *
+ */
+
+/delete-node/ &hyp_mem;
+/delete-node/ &xbl_mem;
+/delete-node/ &sec_apps_mem;
+
+/* Increase the size from 2MB to 8MB */
+&rmtfs_mem {
+	reg = <0x0 0x83600000 0x0 0x800000>;
+};
+
+/ {
+	reserved-memory {
+		adsp_mem: memory@86700000 {
+			reg = <0x0 0x86700000 0x0 0x2800000>;
+			no-map;
+		};
+
+		camera_mem: memory@8ad00000 {
+			reg = <0x0 0x8ad00000 0x0 0x500000>;
+			no-map;
+		};
+
+		venus_mem: memory@8b200000 {
+			reg = <0x0 0x8b200000 0x0 0x500000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8b800000 {
+			reg = <0x0 0x8b800000 0x0 0xf600000>;
+			no-map;
+		};
+
+		wpss_mem: memory@9ae00000 {
+			reg = <0x0 0x9ae00000 0x0 0x1900000>;
+			no-map;
+		};
+
+		mba_mem: memory@9c700000 {
+			reg = <0x0 0x9c700000 0x0 0x200000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart5;
+		serial1 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* FIXED REGULATORS - parents above children */
+
+	/* This is the top level supply and variable voltage */
+	ppvar_sys: ppvar-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ppvar_sys";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/* This divides ppvar_sys by 2, so voltage is variable */
+	src_vph_pwr: src-vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "src_vph_pwr";
+
+		/* EC turns on with switchcap_on; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&ppvar_sys>;
+	};
+
+	pp5000_s3: pp5000-s3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp5000_s3";
+
+		/* EC turns on with en_pp5000_s3; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		vin-supply = <&ppvar_sys>;
+	};
+
+	pp3300_z1: pp3300-z1-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_z1";
+
+		/* EC turns on with en_pp3300_z1; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&ppvar_sys>;
+	};
+
+	pp3300_audio:
+	pp3300_codec: pp3300-codec-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_codec";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_codec>;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp3300_cam:
+	pp3300_edp:
+	pp3300_ts: pp3300-edp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_edp";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_dx_edp>;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp3300_fp:
+	pp3300_fp_ls:
+	pp3300_mcu: pp3300-fp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_fp";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-boot-on;
+		regulator-always-on;
+
+		/*
+		 * WARNING: it is intentional that GPIO 42 isn't listed here.
+		 * The userspace script for updating the fingerprint firmware
+		 * needs to control the FP regulators during a FW update,
+		 * hence the signal can't be owned by the kernel regulator.
+		 */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_fp_rails>;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp3300_hub: pp3300-hub-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_hub";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-boot-on;
+		regulator-always-on;
+
+		gpio = <&tlmm 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_hub>;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp3300_tp: pp3300-tp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_tp";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		/* AP turns on with PP1800_L18B_S0; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp2850_uf_cam: pp2850-uf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp2850_uf_cam";
+
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+
+		gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&uf_cam_en>;
+
+		vin-supply = <&pp3300_cam>;
+	};
+
+	pp2850_vcm_wf_cam: pp2850-vcm-wf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp2850_vcm_wf_cam";
+
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wf_cam_en>;
+
+		vin-supply = <&pp3300_cam>;
+	};
+
+	pp2850_wf_cam: pp2850-wf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp2850_wf_cam";
+
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 *
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&wf_cam_en>;
+		 */
+
+		vin-supply = <&pp3300_cam>;
+	};
+
+	pp1800_fp: pp1800-fp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_fp";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-boot-on;
+		regulator-always-on;
+
+		/*
+		 * WARNING: it is intentional that GPIO 42 isn't listed here.
+		 * The userspace script for updating the fingerprint firmware
+		 * needs to control the FP regulators during a FW update,
+		 * hence the signal can't be owned by the kernel regulator.
+		 */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_fp_rails>;
+
+		vin-supply = <&pp1800_l18b_s0>;
+		status = "disabled";
+	};
+
+	pp1800_uf_cam: pp1800-uf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_uf_cam";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 *
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&uf_cam_en>;
+		 */
+
+		vin-supply = <&pp1800_l19b>;
+	};
+
+	pp1800_wf_cam: pp1800-wf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_wf_cam";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 *
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&wf_cam_en>;
+		 */
+
+		vin-supply = <&pp1800_l19b>;
+	};
+
+	pp1200_wf_cam: pp1200-wf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1200_wf_cam";
+
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 *
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&wf_cam_en>;
+		 */
+
+		vin-supply = <&pp1200_l6b>;
+	};
+
+	/* BOARD-SPECIFIC TOP LEVEL NODES */
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		status = "disabled";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pen_pdct_l>;
+
+		pen_insert: pen-insert {
+			label = "Pen Insert";
+
+			/* Insert = low, eject = high */
+			gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_PEN_INSERTED>;
+			linux,input-type = <EV_SW>;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+		status = "disabled";
+		keyboard_backlight: keyboard-backlight {
+			status = "disabled";
+			label = "cros_ec::kbd_backlight";
+			pwms = <&cros_ec_pwm 0>;
+			max-brightness = <1023>;
+		};
+	};
+};
+
+&apps_rsc {
+	pm7325-regulators {
+		compatible = "qcom,pm7325-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd19_pmu_pcie_i:
+		vdd19_pmu_rfa_i:
+		vreg_s1b_wlan:
+		vreg_s1b: smps1 {
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vdd_pmu_aon_i:
+		vreg_s7b_wlan:
+		vreg_s7b: smps7 {
+			regulator-min-microvolt = <535000>;
+			regulator-max-microvolt = <1120000>;
+		};
+
+		vdd13_pmu_pcie_i:
+		vdd13_pmu_rfa_i:
+		vreg_s8b_wlan:
+		vreg_s8b: smps8 {
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1500000>;
+		};
+
+		vdda_usb_ss_dp_core:
+		vreg_l1b: ldo1 {
+			regulator-min-microvolt = <825000>;
+			regulator-max-microvolt = <925000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_usb_hs0_3p1:
+		vreg_l2b: ldo2 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp1200_l6b:
+		vdd_ufs_1p2:
+		vdd_vref:
+		vdda_csi01_1p2:
+		vdda_csi23_1p2:
+		vdda_csi4_1p2:
+		vdda_dsi0_1p2:
+		vdda_pcie0_1p2:
+		vdda_pcie1_1p2:
+		vdda_usb_ss_dp_1p2:
+		vdda_qlink0_1p2_ck:
+		vdda_qlink1_1p2_ck:
+		vreg_l6b_1p2:
+		vreg_l6b: ldo6 {
+			regulator-min-microvolt = <1120000>;
+			regulator-max-microvolt = <1408000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp2950_l7b:
+		vreg_l7b: ldo7 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		codec_vcc:
+		pp1800_l18b_s0:
+		pp1800_ts:
+		vdd1:
+		vddpx_0:
+		vddpx_3:
+		vddpx_7:
+		vreg_l18b: ldo18 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp1800_l19b:
+		vddpx_ts:
+		vddpx_wl4otp:
+		vreg_l19b: ldo19 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8350c-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_s1c: smps1 {
+			regulator-min-microvolt = <2190000>;
+			regulator-max-microvolt = <2210000>;
+		};
+
+		vddpx_1:
+		vreg_s9c: smps9 {
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1170000>;
+		};
+
+		pp1800_l1c:
+		pp1800_pen:
+		vdd_a_gfx_cs_1p1:
+		vdd_a_cxo_1p8:
+		vdd_qfprom:
+		vdda_apc_cs_1p8:
+		vdda_qrefs_1p8:
+		vdda_turing_q6_cs_1p8:
+		vdda_usb_hs0_1p8:
+		vreg_l1c: ldo1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		dmic_vdd:
+		pp1800_alc5682:
+		pp1800_l2c:
+		pp1800_vreg_alc5682:
+		vreg_l2c: ldo2 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp3300_sar:
+		pp3300_sensor:
+		vreg_l3c: ldo3 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3540000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ppvar_uim1:
+		vddpx_5:
+		vreg_l4c: ldo4 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp2950_l5c:
+		uim_vcc:
+		vddpx_6:
+		vreg_l5c: ldo5 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ppvar_l6c:
+		vddpx_2:
+		vreg_l6c: ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp1800_prox:
+		pp1800_sar:
+		vreg_l8c: ldo8 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp2950_l9c:
+		vreg_l9c: ldo9 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_a_gnss_0p9:
+		vdd_ufs_core:
+		vdd_usb_hs0_core:
+		vdd_vref_0p9:
+		vdda_csi01_0p9:
+		vdda_csi23_0p9:
+		vdda_csi4_0p9:
+		vdda_dsi0_pll_0p9:
+		vdda_dsi0_0p9:
+		vdda_pcie0_core:
+		vdda_pcie1_core:
+		vdda_qlink0_0p9:
+		vdda_qlink1_0p9:
+		vdda_qlink0_0p9_ck:
+		vdda_qlink1_0p9_ck:
+		vdda_qrefs_0p875:
+		vreg_l10c_0p8:
+		vreg_l10c: ldo10 {
+			regulator-min-microvolt = <720000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp2800_l11c:
+		vreg_l11c: ldo11 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp1800_l12c:
+		vreg_l12c: ldo12 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp3300_l13c:
+		vreg_l13c: ldo13 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+	};
+};
+
+ap_tp_i2c: &i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@15 {
+		compatible = "elan,ekth3000";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <102 IRQ_TYPE_EDGE_FALLING>;
+
+		vcc-supply = <&pp3300_z1>;
+
+		wakeup-source;
+	};
+};
+
+ap_h1_i2c: &i2c12 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tpm@50 {
+		compatible = "google,cr50";
+		reg = <0x50>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&h1_ap_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <54 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+ap_ts_pen: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <81 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+
+		vdd-supply = <&pp3300_ts>;
+	};
+};
+
+&pm7325_gpios {
+	status = "disabled"; /* No GPIOs are connected */
+};
+
+&pmk8350_gpios {
+	status = "disabled"; /* No GPIOs are connected */
+};
+
+&pmk8350_pon {
+	status = "disabled";
+};
+
+&pmk8350_rtc {
+	status = "disabled";
+};
+
+&pmk8350_vadc {
+	pmk8350_die_temp {
+		reg = <PMK8350_ADC7_DIE_TEMP>;
+		label = "pmk8350_die_temp";
+		qcom,pre-scaling = <1 1>;
+	};
+
+	pmr735a_die_temp {
+		reg = <PMR735A_ADC7_DIE_TEMP>;
+		label = "pmr735a_die_temp";
+		qcom,pre-scaling = <1 1>;
+	};
+};
+
+&qfprom {
+	vcc-supply = <&vdd_qfprom>;
+};
+
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+
+		spi-max-frequency = <37500000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+	vmmc-supply = <&pp2950_l7b>;
+	vqmmc-supply = <&pp1800_l19b>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+	vmmc-supply = <&pp2950_l9c>;
+	vqmmc-supply = <&ppvar_l6c>;
+
+	cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
+};
+
+ap_ec_spi: &spi8 {
+	status = "okay";
+
+	pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs_gpio_init_high>, <&qup_spi8_cs_gpio>;
+	cs-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+
+	cros_ec: ec@0 {
+		compatible = "google,cros-ec-spi";
+		reg = <0>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <142 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ap_ec_int_l>;
+		spi-max-frequency = <3000000>;
+
+		cros_ec_pwm: ec-pwm {
+			compatible = "google,cros-ec-pwm";
+			#pwm-cells = <1>;
+		};
+
+		i2c_tunnel: i2c-tunnel {
+			compatible = "google,cros-ec-i2c-tunnel";
+			google,remote-bus = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		typec {
+			compatible = "google,cros-ec-typec";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb_c0: connector@0 {
+				compatible = "usb-c-connector";
+				reg = <0>;
+				label = "left";
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+
+			usb_c1: connector@1 {
+				compatible = "usb-c-connector";
+				reg = <1>;
+				label = "right";
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+		};
+	};
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
+
+&keyboard_controller {
+	function-row-physmap = <
+		MATRIX_KEY(0x00, 0x02, 0)	/* T1 */
+		MATRIX_KEY(0x03, 0x02, 0)	/* T2 */
+		MATRIX_KEY(0x02, 0x02, 0)	/* T3 */
+		MATRIX_KEY(0x01, 0x02, 0)	/* T4 */
+		MATRIX_KEY(0x03, 0x04, 0)	/* T5 */
+		MATRIX_KEY(0x02, 0x04, 0)	/* T6 */
+		MATRIX_KEY(0x01, 0x04, 0)	/* T7 */
+		MATRIX_KEY(0x02, 0x09, 0)	/* T8 */
+		MATRIX_KEY(0x01, 0x09, 0)	/* T9 */
+		MATRIX_KEY(0x00, 0x04, 0)	/* T10 */
+	>;
+	linux,keymap = <
+		MATRIX_KEY(0x00, 0x02, KEY_BACK)
+		MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
+		MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
+		MATRIX_KEY(0x01, 0x02, KEY_SCALE)
+		MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
+		MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+		MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+		MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+		MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+
+		CROS_STD_MAIN_KEYMAP
+	>;
+};
+
+&uart5 {
+	compatible = "qcom,geni-debug-uart";
+	status = "okay";
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vdd_usb_hs0_core>;
+	vdda33-supply = <&vdda_usb_hs0_3p1>;
+	vdda18-supply = <&vdda_usb_hs0_1p8>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_usb_ss_dp_1p2>;
+	vdda-pll-supply = <&vdda_usb_ss_dp_core>;
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vdd_usb_hs0_core>;
+	vdda33-supply = <&vdda_usb_hs0_3p1>;
+	vdda18-supply = <&vdda_usb_hs0_1p8>;
+};
+
+/* PINCTRL - additions to nodes defined in sc7280.dtsi */
+
+&qspi_cs0 {
+	bias-disable;
+};
+
+&qspi_clk {
+	bias-disable;
+};
+
+&qspi_data01 {
+	/* High-Z when no transfers; nice to park the lines */
+	bias-pull-up;
+};
+
+&qup_uart5_rx {
+	drive-strength = <2>;
+	bias-pull-up;
+};
+
+&qup_uart5_tx {
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_cts {
+	/*
+	 * Configure a pull-down on CTS to match the pull of
+	 * the Bluetooth module.
+	 */
+	bias-pull-down;
+};
+
+&qup_uart7_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	bias-pull-up;
+};
+
+&sdc1_on {
+	clk {
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	cmd {
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	data {
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	rclk {
+		bias-pull-down;
+	};
+};
+
+&sdc2_on {
+	clk {
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	cmd {
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	data {
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	sd-cd {
+		pins = "gpio91";
+		bias-pull-up;
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&pm8350c_gpios {
+	gpio-line-names = "AP_SUSPEND",
+			  "",
+			  "",
+			  "AP_BL_EN",
+			  "",
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "AP_BL_PWM";
+
+	ap_bl_en: ap-bl-en {
+		pins = "gpio4";
+		function = "normal";
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+		bias-disable;
+
+		/* Force backlight to be disabled to match state at boot. */
+		output-low;
+	};
+};
+
+&tlmm {
+	gpio-line-names = "HP_I2C_SDA",			/* 0 */
+			  "HP_I2C_SCL",
+			  "SSD_RST_L",
+			  "PE_WAKE_ODL",
+			  "AP_TP_I2C_SDA",
+			  "AP_TP_I2C_SCL",
+			  "UF_CAM_EN",
+			  "WF_CAM_EN",
+			  "AP_SAR_SENSOR_SDA",
+			  "AP_SAR_SENSOR_SCL",
+
+			  "",				/* 10 */
+			  "",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  "AP_SPI_CLK",
+			  "AP_SPI_CS0_L",
+			  "",
+			  "",
+			  "EDP_HPD",
+			  "",
+
+			  "UF_CAM_RST_L",		/* 20 */
+			  "WF_CAM_RST_L",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "EN_PP3300_HUB",
+			  "",
+			  "HOST2WLAN_SOL",
+			  "WLAN2HOST_SOL",
+			  "BT_UART_CTS",
+			  "BT_UART_RTS",
+
+			  "BT_UART_TXD",		/* 30 */
+			  "BT_UART_RXD",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "",
+			  "",
+			  "",
+			  "PEN_PDCT_L",
+
+			  "IO_BRD_ID0",			/* 40 */
+			  "IO_BRD_ID1",
+			  "EN_FP_RAILS",
+			  "PEN_IRQ_L",
+			  "AP_SPI_FP_MISO",
+			  "AP_SPI_FP_MOSI",
+			  "AP_SPI_FP_CLK",
+			  "AP_SPI_FP_CS_L",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+
+			  "AP_H1_SPI_CLK",		/* 50 */
+			  "AP_H1_SPI_CS_L",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "LCM_RST_1V8_L",
+			  "AMP_EN",
+			  "",
+			  "DP_HOT_PLUG_DET",
+
+			  "HUB_RST_L",			/* 60 */
+			  "FP_TO_AP_IRQ_L",
+			  "",
+			  "",
+			  "UF_CAM_MCLK",
+			  "WF_CAM_MCLK",
+			  "IO_BRD_ID2",
+			  "EN_PP3300_CODEC",
+			  "EC_IN_RW_ODL",
+			  "UF_CAM_SDA",
+
+			  "UF_CAM_SCL",			/* 70 */
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "AP_BRD_ID0",
+			  "AP_BRD_ID1",
+			  "AP_BRD_ID2",
+			  "",
+			  "FPMCU_BOOT0",
+			  "FP_RST_L",
+			  "PE_CLKREQ_ODL",
+
+			  "EN_EDP_PP3300",		/* 80 */
+			  "TS_INT_L",
+			  "FORCE_USB_BOOT",
+			  "WCD_RST_L",
+			  "WLAN_EN",
+			  "BT_EN",
+			  "WLAN_SW_CTRL",
+			  "PCIE0_RESET_L",
+			  "PCIE0_CLK_REQ_L",
+			  "PCIE0_WAKE_L",
+
+			  "AS_EN",			/* 90 */
+			  "SD_CD_ODL",
+			  "",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "BT_WLAN_SB_CLK",
+			  "BT_WLAN_SB_DATA",
+			  "HP_MCLK",
+			  "HP_BCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+
+			  "HP_LRCLK",			/* 100 */
+			  "HP_IRQ",
+			  "TP_INT_ODL",
+			  "",
+			  "IO_SKU_ID2",
+			  "TS_RESET_L",
+			  "AMP_BCLK",
+			  "AMP_DIN",
+			  "AMP_LRCLK",
+			  "UIM2_DATA",
+
+			  "UIM2_CLK",			/* 110 */
+			  "UIM2_RST",
+			  "UIM2_PRESENT",
+			  "UIM1_DATA",
+			  "UIM1_CLK",
+			  "UIM1_RST",
+			  "",
+			  "RFFE0_CLK",
+			  "RFFE0_DATA/BOOT_CONFIG_0",
+			  "RFFE1_CLK",
+
+			  "RFFE1_DATA/BOOT_CONFIG_1",	/* 120 */
+			  "RFFE2_CLK",
+			  "RFFE2_DATA/BOOT_CONFIG_2",
+			  "RFFE3_CLK",
+			  "RFFE3_DATA/BOOT_CONFIG_3",
+			  "RFFE4_CLK",
+			  "RFFE4_DATA",
+			  "WCI2_LTE_COEX_RXD",
+			  "WCI2_LTE_COEX_TXD",
+			  "IO_SKU_ID0",
+
+			  "IO_SKU_ID1",			/* 130 */
+			  "",
+			  "",
+			  "QLINK0_REQ",
+			  "QLINK0_EN",
+			  "QLINK0_WMSS_RESET_L",
+			  "QLINK1_REQ",
+			  "QLINK1_EN",
+			  "QLINK1_WMSS_RESET_L",
+			  "FORCED_USB_BOOT_POL",
+
+			  "",				/* 140 */
+			  "P_SENSOR_INT_L",
+			  "AP_EC_INT_L",
+			  "",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA_0",
+			  "WCD_SWR_TX_DATA_1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA_0",
+			  "WCD_SWR_RX_DATA_1",
+
+			  "",				/* 150 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "WCD_SWR_TX_DATA_2",
+			  "",
+
+			  "",				/* 160 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 170 */
+			  "SENS_UART_TXD",
+			  "SENS_UART_RXD",
+			  "",
+			  "",
+			  "";
+
+	/*
+	 * pinctrl settings for pins that have no real owners.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&bios_flash_wp_l>;
+
+	amp_en: amp-en {
+		pins = "gpio57";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	ap_ec_int_l: ap-ec-int-l {
+		pins = "gpio142";
+		input-enable;
+		bias-pull-up;
+	};
+
+	bios_flash_wp_l: bios-flash-wp-l {
+		pins = "gpio93";
+		function = "gpio";
+		input-enable;
+		bias-disable;
+	};
+
+	bt_en: bt-en {
+		pins = "gpio85";
+		function = "gpio";
+		drive-strength = <2>;
+		output-low;
+		bias-pull-down;
+	};
+
+	en_fp_rails: en-fp-rails {
+		pins = "gpio42";
+		drive-strength = <2>;
+		output-high;
+		bias-disable;
+	};
+
+	en_pp3300_codec: en-pp3300-codec {
+		pins = "gpio67";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	en_pp3300_dx_edp: en-pp3300-dx-edp {
+		pins = "gpio80";
+		function = "gpio";
+		drive-strength = <2>;
+		/* Has external pulldown */
+		bias-disable;
+	};
+
+	en_pp3300_hub: en-pp3300-hub {
+		pins = "gpio24";
+		function = "gpio";
+		drive-strength = <2>;
+		/* Has external pulldown */
+		bias-disable;
+	};
+
+	fp_to_ap_irq_l: fp-to-ap-irq-l {
+		pins = "gpio61";
+		function = "gpio";
+		input-enable;
+		/* Has external pullup */
+		bias-disable;
+	};
+
+	h1_ap_int_odl: h1-ap-int-odl {
+		pins = "gpio54";
+		function = "gpio";
+		input-enable;
+		bias-pull-up;
+	};
+
+	hp_irq: hp-irq {
+		pins = "gpio101";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	p_sensor_int_l: p-sensor-int-l {
+		pins = "gpio141";
+		function = "gpio";
+		input-enable;
+		bias-pull-up;
+	};
+
+	pen_irq_l: pen-irq-l {
+		pins = "gpio43";
+		function = "gpio";
+		/* Has external pullup */
+		bias-disable;
+	};
+
+	pen_pdct_l: pen-pdct-l {
+		pins = "gpio39";
+		function = "gpio";
+		/* Has external pullup */
+		bias-disable;
+	};
+
+	qup_spi8_cs_gpio_init_high: qup-spi8-cs-gpio-init-high {
+		pins = "gpio35";
+		output-high;
+	};
+
+	qup_spi11_cs_gpio_init_high: qup-spi11-cs-gpio-init-high {
+		pins = "gpio47";
+		output-high;
+	};
+
+	qup_spi12_cs_gpio_init_high: qup-spi12-cs-gpio-init-high {
+		pins = "gpio51";
+		output-high;
+	};
+
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		 * Configure a pull-down on CTS to match the pull of
+		 * the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+
+	tp_int_odl: tp-int-odl {
+		pins = "gpio102";
+		function = "gpio";
+		/* Has external pullup */
+		bias-disable;
+	};
+
+	ts_int_l: ts-int-l {
+		pins = "gpio81";
+		function = "gpio";
+		/* Has external pullup */
+		bias-pull-up;
+	};
+
+	ts_reset_l: ts-reset-l {
+		pins = "gpio105";
+		function = "gpio";
+		/* Has external pullup */
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	uf_cam_en: uf-cam-en {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		/* Has external pulldown */
+		bias-disable;
+	};
+
+	wf_cam_en: wf-cam-en {
+		pins = "gpio7";
+		function = "gpio";
+		drive-strength = <2>;
+		/* Has external pulldown */
+		bias-disable;
+	};
+};
