diff mbox series

[6/7] ARM: dts: qcom: msm8226: add USB node

Message ID 20211118210210.160895-6-luca@z3ntu.xyz (mailing list archive)
State Accepted
Headers show
Series [1/7] dt-bindings: power: supply: pm8941-charger: add pm8226 | expand

Commit Message

Luca Weiss Nov. 18, 2021, 9:02 p.m. UTC 
Add a node describing the MSM8226 USB controller and phy.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 arch/arm/boot/dts/qcom-msm8226.dtsi | 39 +++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
index 7d48599502b3..103c0ab70814 100644
--- a/arch/arm/boot/dts/qcom-msm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
@@ -8,6 +8,7 @@ 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8974.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/reset/qcom,gcc-msm8974.h>
 
 / {
 	#address-cells = <1>;
@@ -229,6 +230,44 @@  blsp1_i2c5: i2c@f9927000 {
 			#size-cells = <0>;
 		};
 
+		usb: usb@f9a55000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0xf9a55000 0x200>,
+			      <0xf9a55200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <75000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			phys = <&usb_hs_phy>;
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8226",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+					reset-names = "phy", "por";
+					qcom,init-seq = /bits/ 8 <0x0 0x44
+						0x1 0x68 0x2 0x24 0x3 0x13>;
+				};
+			};
+		};
+
 		gcc: clock-controller@fc400000 {
 			compatible = "qcom,gcc-msm8226";
 			reg = <0xfc400000 0x4000>;