@@ -497,20 +497,20 @@ config {
&pcie0 {
status = "okay";
- perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
vddpe-3v3-supply = <&wlan_en>;
vdda-supply = <&vreg_l28a_0p925>;
};
&pcie1 {
status = "okay";
- perst-gpio = <&tlmm 130 GPIO_ACTIVE_LOW>;
+ perst-gpios = <&tlmm 130 GPIO_ACTIVE_LOW>;
vdda-supply = <&vreg_l28a_0p925>;
};
&pcie2 {
status = "okay";
- perst-gpio = <&tlmm 114 GPIO_ACTIVE_LOW>;
+ perst-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
vdda-supply = <&vreg_l28a_0p925>;
};
@@ -54,12 +54,12 @@ &blsp1_uart5 {
&pcie0 {
status = "okay";
- perst-gpio = <&tlmm 61 0x1>;
+ perst-gpios = <&tlmm 61 0x1>;
};
&pcie1 {
status = "okay";
- perst-gpio = <&tlmm 58 0x1>;
+ perst-gpios = <&tlmm 58 0x1>;
};
&pcie_phy0 {
@@ -44,12 +44,12 @@ &blsp1_uart5 {
&pcie0 {
status = "ok";
- perst-gpio = <&tlmm 58 0x1>;
+ perst-gpios = <&tlmm 58 0x1>;
};
&pcie1 {
status = "ok";
- perst-gpio = <&tlmm 61 0x1>;
+ perst-gpios = <&tlmm 61 0x1>;
};
&pcie_phy0 {
@@ -195,8 +195,8 @@ &mmcc {
&pcie0 {
status = "okay";
- perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
- wake-gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
vddpe-3v3-supply = <&wlan_en>;
vdda-supply = <&pm8994_l28>;
};
@@ -99,7 +99,7 @@ pms405_s3: s3 {
&pcie {
status = "okay";
- perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ perst-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&perst_state>;
@@ -362,7 +362,7 @@ &pcie1 {
pinctrl-names = "default";
pinctrl-0 = <&pcie1_clkreq_n>, <&ssd_rst_l>, <&pe_wake_odl>;
- perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
vddpe-3v3-supply = <&pp3300_ssd>;
};
@@ -240,7 +240,7 @@ &ipa {
&pcie1 {
status = "okay";
- perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
vddpe-3v3-supply = <&nvme_3v3_regulator>;
@@ -502,7 +502,7 @@ &mss_pil {
&pcie0 {
status = "okay";
- perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
vddpe-3v3-supply = <&pcie0_3p3v_dual>;
@@ -520,7 +520,7 @@ &pcie0_phy {
&pcie1 {
status = "okay";
- perst-gpio = <&tlmm 102 GPIO_ACTIVE_LOW>;
+ perst-gpios = <&tlmm 102 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie1_default_state>;