diff mbox series

[v2,1/6] arm64: dts: qcom: sa8155p-adp: Specify which LDO modes are allowed

Message ID 20220829094903.v2.1.Id59c32b560c4662d8b3697de2bd494d08d654806@changeid (mailing list archive)
State Accepted
Headers show
Series arm64: dts: qcom: Fix broken regulator spec on RPMH boards | expand

Commit Message

Doug Anderson Aug. 29, 2022, 4:49 p.m. UTC
This board uses RPMH, specifies "regulator-allow-set-load" for LDOs,
but doesn't specify any modes with "regulator-allowed-modes".

Prior to commit efb0cb50c427 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()") the above meant that we were able
to set either LPM or HPM mode. After that commit (and fixes [1]) we'll
be stuck at the initial mode. Discussion of this has resulted in the
decision that the old dts files were wrong and should be fixed to
fully restore old functionality.

Let's re-enable the old functionality by fixing the dts.

NOTE: while here, let's also remove the nonsensical
"regulator-allow-set-load" on the fixed regulator "vreg_s4a_1p8".

[1] https://lore.kernel.org/r/20220824142229.RFT.v2.2.I6f77860e5cd98bf5c67208fa9edda4a08847c304@changeid

Fixes: 5b85e8f2225c ("arm64: dts: qcom: sa8155p-adp: Add base dts file")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---

Changes in v2:
- Added note about removing regulator-allow-set-load from vreg_s4a_1p8

 arch/arm64/boot/dts/qcom/sa8155p-adp.dts | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
index ba547ca9fc6b..ddb9cb182152 100644
--- a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
+++ b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
@@ -43,7 +43,6 @@  vreg_s4a_1p8: smps4 {
 
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-allow-set-load;
 
 		vin-supply = <&vreg_3p3>;
 	};
@@ -137,6 +136,9 @@  vreg_l5a_0p88: ldo5 {
 			regulator-max-microvolt = <880000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7a_1p8: ldo7 {
@@ -152,6 +154,9 @@  vreg_l10a_2p96: ldo10 {
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l11a_0p8: ldo11 {
@@ -258,6 +263,9 @@  vreg_l5c_1p2: ldo5 {
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_1p8: ldo7 {
@@ -273,6 +281,9 @@  vreg_l8c_1p2: ldo8 {
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {