diff mbox series

[1/2] arm64: dts: qcom: sc7280: Add device tree for herobrine evoker

Message ID 20220901170958.1.I7dd7a79c4cc5fe91c3feb004473feb3b34b7b2d8@changeid (mailing list archive)
State Superseded
Headers show
Series Add a new board device tree named 'evoker' for herobrine variant. | expand

Commit Message

Sheng-Liang Pan Sept. 1, 2022, 9:12 a.m. UTC
Add a basic device tree for the herobrine evoker board.

Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
---

 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/sc7280-herobrine-evoker-r0.dts   | 333 ++++++++++++++++++
 2 files changed, 334 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts

Comments

Krzysztof Kozlowski Sept. 1, 2022, 10:01 a.m. UTC | #1
On 01/09/2022 12:12, Sheng-Liang Pan wrote:
> Add a basic device tree for the herobrine evoker board.
> 
> Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
> ---

And this is third v1? At least this is what your subject is suggesting.
Patches should be properly versioned. Git format-patch helps in that,
but you can use any other tools if you wish.

I pointed you to documentation you must read before posting. You can
keep ignoring it, so we keep ignoring your patch.

That's a NAK :(

Best regards,
Krzysztof
Doug Anderson Sept. 1, 2022, 3:06 p.m. UTC | #2
Hi,

On Thu, Sep 1, 2022 at 3:01 AM Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
>
> On 01/09/2022 12:12, Sheng-Liang Pan wrote:
> > Add a basic device tree for the herobrine evoker board.
> >
> > Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
> > ---
>
> And this is third v1? At least this is what your subject is suggesting.
> Patches should be properly versioned. Git format-patch helps in that,
> but you can use any other tools if you wish.

Just to make it clear, what Krzysztof is pointing at is the subject
line of your email. Based on your email headers it looks like you're
using "patman" to send out your emails. That means you can get what
Krzysztof wants by putting a "Series-version" in one of your patches.
Given that you had three v1 posts, maybe call the next version "v4"?
That means that one of the patches should have:

Series-version: 4

Then in each patch you'll have details about what changed in each
version. I guess we could sorta call the one where you added the
bindings "v2". So in the bindings patch you could add:

Series-changes: 2
- Bindings patch added

...and in both patches you could add:

Series-changes: 4
- Got the version number correct


You've already got a cover letter setup, so in that you should attempt
to explain some of this mess, like saying:

Sorry about getting mixed up with version numbers. Here are links to
previous postings and what I'll assume the version number is:

v1: https://lore.kernel.org/r/20220830053307.3997495-1-sheng-liang.pan@quanta.corp-partner.google.com/
v2: https://lore.kernel.org/r/20220901061336.61386-1-sheng-liang.pan@quanta.corp-partner.google.com/
v3: https://lore.kernel.org/r/20220901091253.93333-1-sheng-liang.pan@quanta.corp-partner.google.com/


As an extra note: the bindings patch should be patch #1 and the device
tree should be patch #2. That means you should reorder your patches.

-Doug

>
> I pointed you to documentation you must read before posting. You can
> keep ignoring it, so we keep ignoring your patch.
>
> That's a NAK :(
>
> Best regards,
> Krzysztof
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1d86a33de528c..dd18ae8cd81c2 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -101,6 +101,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev1-boe-rt5682s.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-crd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-evoker-r0.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-herobrine-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-villager-r0.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts
new file mode 100644
index 0000000000000..ccbe50b6249ab
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts
@@ -0,0 +1,333 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Evoker board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine.dtsi"
+
+/ {
+	model = "Google Evoker";
+	compatible = "google,evoker", "qcom,sc7280";
+};
+
+/*
+ * ADDITIONS TO FIXED REGULATORS DEFINED IN PARENT DEVICE TREE FILES
+ *
+ * Sort order matches the order in the parent files (parents before children).
+ */
+
+&pp3300_codec {
+	status = "okay";
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+ap_tp_i2c: &i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+		hid-descr-addr = <0x20>;
+		vcc-supply = <&pp3300_z1>;
+
+		wakeup-source;
+	};
+};
+
+ts_i2c: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "elan,ekth6915";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+
+		vcc33-supply = <&ts_avdd>;
+	};
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
+
+&ap_sar_sensor0 {
+	status = "okay";
+};
+
+&ap_sar_sensor1 {
+	status = "okay";
+};
+
+&mdss_edp {
+	status = "okay";
+};
+
+&mdss_edp_phy {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1 {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1_phy {
+	status = "okay";
+};
+
+&pwmleds {
+	status = "okay";
+};
+
+/* For eMMC */
+&sdhc_1 {
+	status = "okay";
+};
+
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+&ts_rst_conn {
+	bias-disable;
+};
+
+/* PINCTRL - BOARD-SPECIFIC */
+
+/*
+ * Methodology for gpio-line-names:
+ * - If a pin goes to herobrine board and is named it gets that name.
+ * - If a pin goes to herobrine board and is not named, it gets no name.
+ * - If a pin is totally internal to Qcard then it gets Qcard name.
+ * - If a pin is not hooked up on Qcard, it gets no name.
+ */
+
+&pm8350c_gpios {
+	gpio-line-names = "FLASH_STROBE_1",		/* 1 */
+			  "AP_SUSPEND",
+			  "PM8008_1_RST_N",
+			  "",
+			  "",
+			  "",
+			  "PMIC_EDP_BL_EN",
+			  "PMIC_EDP_BL_PWM",
+			  "";
+};
+
+&tlmm {
+	gpio-line-names = "AP_TP_I2C_SDA",		/* 0 */
+			  "AP_TP_I2C_SCL",
+			  "SSD_RST_L",
+			  "PE_WAKE_ODL",
+			  "AP_SAR_SDA",
+			  "AP_SAR_SCL",
+			  "PRB_SC_GPIO_6",
+			  "TP_INT_ODL",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+
+			  "GNSS_L1_EN",			/* 10 */
+			  "GNSS_L5_EN",
+			  "SPI_AP_MOSI",
+			  "SPI_AP_MISO",
+			  "SPI_AP_CLK",
+			  "SPI_AP_CS0_L",
+			  /*
+			   * AP_FLASH_WP is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_OD.
+			   */
+			  "AP_FLASH_WP",
+			  "",
+			  "AP_EC_INT_L",
+			  "",
+
+			  "UF_CAM_RST_L",		/* 20 */
+			  "WF_CAM_RST_L",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "",
+			  "PM8008_IRQ_1",
+			  "HOST2WLAN_SOL",
+			  "WLAN2HOST_SOL",
+			  "MOS_BT_UART_CTS",
+			  "MOS_BT_UART_RFR",
+
+			  "MOS_BT_UART_TX",		/* 30 */
+			  "MOS_BT_UART_RX",
+			  "PRB_SC_GPIO_32",
+			  "HUB_RST_L",
+			  "",
+			  "",
+			  "AP_SPI_FP_MISO",
+			  "AP_SPI_FP_MOSI",
+			  "AP_SPI_FP_CLK",
+			  "AP_SPI_FP_CS_L",
+
+			  "AP_EC_SPI_MISO",		/* 40 */
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "LCM_RST_L",
+			  "EARLY_EUD_N",
+			  "",
+			  "DP_HOT_PLUG_DET",
+			  "IO_BRD_MLB_ID0",
+			  "IO_BRD_MLB_ID1",
+
+			  "IO_BRD_MLB_ID2",		/* 50 */
+			  "SSD_EN",
+			  "TS_I2C_SDA_CONN",
+			  "TS_I2C_CLK_CONN",
+			  "TS_RST_CONN",
+			  "TS_INT_CONN",
+			  "AP_I2C_TPM_SDA",
+			  "AP_I2C_TPM_SCL",
+			  "PRB_SC_GPIO_58",
+			  "PRB_SC_GPIO_59",
+
+			  "EDP_HOT_PLUG_DET_N",		/* 60 */
+			  "FP_TO_AP_IRQ_L",
+			  "",
+			  "AMP_EN",
+			  "CAM0_MCLK_GPIO_64",
+			  "CAM1_MCLK_GPIO_65",
+			  "WF_CAM_MCLK",
+			  "PRB_SC_GPIO_67",
+			  "FPMCU_BOOT0",
+			  "UF_CAM_SDA",
+
+			  "UF_CAM_SCL",			/* 70 */
+			  "",
+			  "",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "",
+			  "",
+			  "EN_FP_RAILS",
+			  "FP_RST_L",
+			  "PCIE1_CLKREQ_ODL",
+
+			  "EN_PP3300_DX_EDP",		/* 80 */
+			  "SC_GPIO_81",
+			  "FORCED_USB_BOOT",
+			  "WCD_RESET_N",
+			  "MOS_WLAN_EN",
+			  "MOS_BT_EN",
+			  "MOS_SW_CTRL",
+			  "MOS_PCIE0_RST",
+			  "MOS_PCIE0_CLKREQ_N",
+			  "MOS_PCIE0_WAKE_N",
+
+			  "MOS_LAA_AS_EN",		/* 90 */
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "MOS_BT_WLAN_SLIMBUS_CLK",
+			  "MOS_BT_WLAN_SLIMBUS_DAT0",
+			  "HP_MCLK",
+			  "HP_BCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+
+			  "HP_LRCLK",			/* 100 */
+			  "HP_IRQ",
+			  "",
+			  "",
+			  "GSC_AP_INT_ODL",
+			  "EN_PP3300_CODEC",
+			  "AMP_BCLK",
+			  "AMP_DIN",
+			  "AMP_LRCLK",
+			  "UIM1_DATA_GPIO_109",
+
+			  "UIM1_CLK_GPIO_110",		/* 110 */
+			  "UIM1_RESET_GPIO_111",
+			  "PRB_SC_GPIO_112",
+			  "UIM0_DATA",
+			  "UIM0_CLK",
+			  "UIM0_RST",
+			  "UIM0_PRESENT_ODL",
+			  "SDM_RFFE0_CLK",
+			  "SDM_RFFE0_DATA",
+			  "WF_CAM_EN",
+
+			  "FASTBOOT_SEL_0",		/* 120 */
+			  "SC_GPIO_121",
+			  "FASTBOOT_SEL_1",
+			  "SC_GPIO_123",
+			  "FASTBOOT_SEL_2",
+			  "SM_RFFE4_CLK_GRFC_8",
+			  "SM_RFFE4_DATA_GRFC_9",
+			  "WLAN_COEX_UART1_RX",
+			  "WLAN_COEX_UART1_TX",
+			  "PRB_SC_GPIO_129",
+
+			  "LCM_ID0",			/* 130 */
+			  "LCM_ID1",
+			  "",
+			  "SDR_QLINK_REQ",
+			  "SDR_QLINK_EN",
+			  "QLINK0_WMSS_RESET_N",
+			  "SMR526_QLINK1_REQ",
+			  "SMR526_QLINK1_EN",
+			  "SMR526_QLINK1_WMSS_RESET_N",
+			  "PRB_SC_GPIO_139",
+
+			  "SAR1_IRQ_ODL",		/* 140 */
+			  "SAR0_IRQ_ODL",
+			  "PRB_SC_GPIO_142",
+			  "",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0",
+			  "WCD_SWR_RX_DATA1",
+
+			  "DMIC01_CLK",			/* 150 */
+			  "DMIC01_DATA",
+			  "DMIC23_CLK",
+			  "DMIC23_DATA",
+			  "",
+			  "",
+			  "EC_IN_RW_ODL",
+			  "HUB_EN",
+			  "WCD_SWR_TX_DATA2",
+			  "",
+
+			  "",				/* 160 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 170 */
+			  "MOS_BLE_UART_TX",
+			  "MOS_BLE_UART_RX",
+			  "",
+			  "",
+			  "";
+};