@@ -1026,6 +1026,7 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8016-sbc.dtb \
qcom-apq8026-asus-sparrow.dtb \
+ qcom-apq8026-huawei-sturgeon.dtb \
qcom-apq8026-lg-lenok.dtb \
qcom-apq8060-dragonboard.dtb \
qcom-apq8064-cm-qs600.dtb \
new file mode 100644
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+
+/ {
+ model = "Huawei Watch";
+ compatible = "huawei,sturgeon", "qcom,apq8026";
+ chassis-type = "watch";
+ qcom,msm-id = <199 0x20000>;
+ qcom,board-id = <8 4>;
+
+ reserved-memory {
+ sbl_region: sbl@2f00000 {
+ reg = <0x02f00000 0x100000>;
+ no-map;
+ };
+
+ external_image_region: external-image@3100000 {
+ reg = <0x3100000 0x200000>;
+ no-map;
+ };
+
+ peripheral_region: peripheral@3300000 {
+ reg = <0x3300000 0x600000>;
+ no-map;
+ };
+
+ adsp_region: adsp@3900000 {
+ reg = <0x3900000 0x1400000>;
+ no-map;
+ };
+
+ modem_region: modem@4d00000 {
+ reg = <0x4d00000 0x1b00000>;
+ no-map;
+ };
+
+ modem_efs_region: modem-efs@7f00000 {
+ reg = <0x7f00000 0x100000>;
+ no-map;
+ };
+ };
+
+ vreg_wlan: wlan-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_regulator_default_state>;
+ };
+};
+
+&adsp {
+ status = "okay";
+};
+
+&blsp1_i2c5 {
+ clock-frequency = <384000>;
+
+ status = "okay";
+
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+
+ interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8226_l19>;
+ vio-supply = <&pm8226_lvs1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_default_state>;
+
+ syna,startup-delay-ms = <160>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
+
+&blsp1_uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart4_default_state>;
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43430a0-bt";
+ max-speed = <3000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bluetooth_default_state>;
+
+ host-wakeup-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&rpm_requests {
+ regulators {
+ compatible = "qcom,rpm-pm8226-regulators";
+
+ pm8226_s3: s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8226_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2200000>;
+ };
+
+ pm8226_s5: s5 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ };
+
+ pm8226_l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pm8226_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l3: l3 {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1337500>;
+ };
+
+ pm8226_l4: l4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l5: l5 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l7: l7 {
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <1850000>;
+ };
+
+ pm8226_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l9: l9 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pm8226_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l14: l14 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ };
+
+ pm8226_l15: l15 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ pm8226_l16: l16 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3350000>;
+ };
+
+ pm8226_l17: l17 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l18: l18 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l19: l19 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pm8226_l20: l20 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ pm8226_l21: l21 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l22: l22 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l23: l23 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l24: l24 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ pm8226_l25: l25 {
+ regulator-min-microvolt = <1775000>;
+ regulator-max-microvolt = <2125000>;
+ };
+
+ pm8226_l26: l26 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pm8226_l27: l27 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pm8226_l28: l28 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_lvs1: lvs1 {};
+ };
+};
+
+&sdhc_1 {
+ vmmc-supply = <&pm8226_l17>;
+ vqmmc-supply = <&pm8226_l6>;
+
+ bus-width = <8>;
+ non-removable;
+
+ status = "okay";
+};
+
+&sdhc_3 {
+ max-frequency = <100000000>;
+ non-removable;
+
+ vmmc-supply = <&vreg_wlan>;
+ vqmmc-supply = <&pm8226_l6>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ wifi@1 {
+ compatible = "brcm,bcm43430a0-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wake";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_hostwake_default_state>;
+ };
+};
+
+&smbb {
+ qcom,fast-charge-safe-voltage = <4370000>;
+ qcom,fast-charge-high-threshold-voltage = <4350000>;
+ qcom,minimum-input-voltage = <4350000>;
+ qcom,fast-charge-current-limit = <300000>;
+ qcom,fast-charge-safe-current = <600000>;
+ qcom,auto-recharge-threshold-voltage = <4240000>;
+};
+
+&tlmm {
+ blsp1_uart4_default_state: blsp1-uart4-default-state {
+ pins = "gpio12", "gpio13", "gpio14", "gpio15";
+ function = "blsp_uart4";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ bluetooth_default_state: bluetooth-default-state {
+ pins = "gpio63", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ touch_default_state: touch-default-state {
+ irq-pins {
+ pins = "gpio17";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ reset-pins {
+ pins = "gpio16";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ wlan_hostwake_default_state: wlan-hostwake-default-state {
+ pins = "gpio66";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
+
+ wlan_regulator_default_state: wlan-regulator-default-state {
+ pins = "gpio110";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+};
+
+&usb {
+ extcon = <&smbb>;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usb_hs_phy {
+ extcon = <&smbb>;
+ v1p8-supply = <&pm8226_l10>;
+ v3p3-supply = <&pm8226_l20>;
+};
Add support for this smartwatch, based on Snapdragon 400 SoC. Currently supported functionality: * Internal storage * USB * Charger * Power button * Bluetooth * Wifi Signed-off-by: Luca Weiss <luca@z3ntu.xyz> --- Changes in v2: * Address review comments from v1: * newlines between reserved-memory and regulator nodes (Konrad) * status as last property in nodes (Konrad) * pm8226-regulators node name change (Krzysztof) * Add -pins suffix to state nodes (Krzysztof) arch/arm/boot/dts/Makefile | 1 + .../boot/dts/qcom-apq8026-huawei-sturgeon.dts | 376 ++++++++++++++++++ 2 files changed, 377 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts