| Message ID | 20220930153538.v5.3.I50d04dcbe735dda69995cf1078824d671501869e@changeid (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add LTE SKU for sc7280-evoker family | expand |
Hi, On Fri, Sep 30, 2022 at 12:38 AM Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com> wrote: > > Change touchpad and touchscreen node for evoker > Touchpad: SA461D-1011 > Touchscreen: GT7986U > > Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com> > --- > > (no changes since v1) nit: for patman, add: Series-changes: 5 - Touchscreen / trackpad patch new for v5. ...and then you won't get the confusing "no changes since v1" message. > .../boot/dts/qcom/sc7280-herobrine-evoker.dtsi | 17 +++++++---------- > 1 file changed, 7 insertions(+), 10 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi > index e78072159d54b..c26f19371c8bc 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi > @@ -23,16 +23,15 @@ ap_tp_i2c: &i2c0 { > status = "okay"; > clock-frequency = <400000>; > > - trackpad: trackpad@2c { > - compatible = "hid-over-i2c"; > - reg = <0x2c>; > + trackpad: trackpad@15 { > + compatible = "elan,ekth3000"; > + reg = <0x15>; > pinctrl-names = "default"; > pinctrl-0 = <&tp_int_odl>; > > interrupt-parent = <&tlmm>; > interrupts = <7 IRQ_TYPE_EDGE_FALLING>; > > - hid-descr-addr = <0x20>; > vcc-supply = <&pp3300_z1>; > > wakeup-source; > @@ -43,18 +42,16 @@ ts_i2c: &i2c13 { > status = "okay"; > clock-frequency = <400000>; > > - ap_ts: touchscreen@10 { > - compatible = "elan,ekth6915"; > - reg = <0x10>; > - pinctrl-names = "default"; > - pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>; Why did you remove the pinctrl? Those should have stayed. > + touchscreen: touchscreen@5d { nit: it's nice to keep the touchscreen label the same as the other herobrine boards, so I'd keep this as: ap_ts: touchscreen@5d { > + compatible = "goodix,gt7375p"; > + reg = <0x5d>; > > interrupt-parent = <&tlmm>; > interrupts = <55 IRQ_TYPE_LEVEL_LOW>; > > reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>; > > - vcc33-supply = <&ts_avdd>; > + vdd-supply = <&ts_avdd>; What you have here is fine, but I've heard rumors that we might end up needing to specify a different IO voltage rail. Right now the goodix bindings / goodix driver don't handle that. ...anyway, no action items for you right now but just a heads up. -Doug
Hi, On Fri, Sep 30, 2022 at 12:38 AM Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com> wrote: > > Change touchpad and touchscreen node for evoker > Touchpad: SA461D-1011 > Touchscreen: GT7986U [...cut...] > + touchscreen: touchscreen@5d { > + compatible = "goodix,gt7375p"; > + reg = <0x5d>; One further note is that in the commit message you've said GT7986U in the commit message but you're specifying "goodix,gt7375p" here. Ideally, what you'd do is: 1. Create a bindings patch modifying "goodix,gt7375p.yaml" much like we did for elan [1]. You'd end up with something like this (untested): compatible: oneOf: - const: goodix,gt7375p - items: - const: goodix,gt7986u - const: goodix,gt7375p 2. You wouldn't need any driver patch unless the timings for gt7986u are different than gt7375p 3. In your device tree, you'd list: compatible = "goodix,gt7986u", "goodix,gt7375p"; ...which says "I really have a gt7986u, but if you don't have any special knowledge about gt7986u then you can just pretend I have a gt7375p". [1] https://lore.kernel.org/r/20220923083657.v5.2.Ic4e8f03868f88b8027a81bc3d414bae68978e6b7@changeid
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi index e78072159d54b..c26f19371c8bc 100644 --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi @@ -23,16 +23,15 @@ ap_tp_i2c: &i2c0 { status = "okay"; clock-frequency = <400000>; - trackpad: trackpad@2c { - compatible = "hid-over-i2c"; - reg = <0x2c>; + trackpad: trackpad@15 { + compatible = "elan,ekth3000"; + reg = <0x15>; pinctrl-names = "default"; pinctrl-0 = <&tp_int_odl>; interrupt-parent = <&tlmm>; interrupts = <7 IRQ_TYPE_EDGE_FALLING>; - hid-descr-addr = <0x20>; vcc-supply = <&pp3300_z1>; wakeup-source; @@ -43,18 +42,16 @@ ts_i2c: &i2c13 { status = "okay"; clock-frequency = <400000>; - ap_ts: touchscreen@10 { - compatible = "elan,ekth6915"; - reg = <0x10>; - pinctrl-names = "default"; - pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>; + touchscreen: touchscreen@5d { + compatible = "goodix,gt7375p"; + reg = <0x5d>; interrupt-parent = <&tlmm>; interrupts = <55 IRQ_TYPE_LEVEL_LOW>; reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>; - vcc33-supply = <&ts_avdd>; + vdd-supply = <&ts_avdd>; }; };
Change touchpad and touchscreen node for evoker Touchpad: SA461D-1011 Touchscreen: GT7986U Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com> --- (no changes since v1) .../boot/dts/qcom/sc7280-herobrine-evoker.dtsi | 17 +++++++---------- 1 file changed, 7 insertions(+), 10 deletions(-)