diff mbox series

[v6,2/2] arm64: dts: qcom: sagit: add initial device tree for sagit

Message ID 20221005181528.1038629-3-dsankouski@gmail.com (mailing list archive)
State Superseded
Headers show
Series add device Xiaomi Mi 6 (codename sagit) and board binding | expand

Commit Message

Dzmitry Sankouski Oct. 5, 2022, 6:15 p.m. UTC
New device support - Xiaomi Mi6 phone

What works:
- storage
- usb
- power regulators

Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/msm8998-xiaomi-sagit.dts    | 681 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/pm8998.dtsi          |   8 +
 3 files changed, 690 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts

Comments

Dzmitry Sankouski Oct. 5, 2022, 6:30 p.m. UTC | #1
Here is changelogs:

Changes for v2:
- remove memory nodes before redefining
- add board compatible to schema
- remove board msm-id, add chassis type
- remove common dtsi
- move resin to pm8998 dtsi file
- dts formatting
- unsupported properties removed
- add copyright
- rebase on latest master(6.0.0-rc6)
Changes for v3:
- regulators nodes renamed to match pattern 'regulators-[01]'
- duplicate cci1-default node deleted
- add state suffix to '.*(active|suspend|default)' pinctrl
- rebase on latest master(6.0.0)
Changes for v4:
- fix dts compilation errors(rename pinctrl label usages)
Changes for v5:
- use pm8005_regulators label
Changes for v6:
- add state suffix to all pinctrl
- move status nodes to last position
- disable resin node by default
- move the debounce param to pm8998.dtsi file
- place this patch after dt-binding patch


ср, 5 окт. 2022 г. в 21:15, Dzmitry Sankouski <dsankouski@gmail.com>:
>
> New device support - Xiaomi Mi6 phone
>
> What works:
> - storage
> - usb
> - power regulators
>
> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/msm8998-xiaomi-sagit.dts    | 681 ++++++++++++++++++
>  arch/arm64/boot/dts/qcom/pm8998.dtsi          |   8 +
>  3 files changed, 690 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 1d86a33de528..0460aabf1b59 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM)       += msm8998-oneplus-dumpling.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-lilac.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-maple.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-poplar.dtb
> +dtb-$(CONFIG_ARCH_QCOM)        += msm8998-xiaomi-sagit.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += qcs404-evb-1000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += qcs404-evb-4000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += qrb5165-rb5.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> new file mode 100644
> index 000000000000..e44f6a745a2c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> @@ -0,0 +1,681 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
> + *
> + * Copyright (c) 2022, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
> + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "msm8998.dtsi"
> +#include "pm8005.dtsi"
> +#include "pm8998.dtsi"
> +#include "pmi8998.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +
> +/*
> + * Delete following upstream (msm8998.dtsi) reserved
> + * memory mappings which are different in this device.
> + */
> +/delete-node/ &mpss_mem;
> +/delete-node/ &venus_mem;
> +/delete-node/ &mba_mem;
> +/delete-node/ &slpi_mem;
> +/delete-node/ &ipa_fw_mem;
> +/delete-node/ &ipa_gsi_mem;
> +/delete-node/ &gpu_mem;
> +/delete-node/ &wlan_msa_mem;
> +
> +/ {
> +       model = "Xiaomi Mi 6";
> +       compatible = "xiaomi,sagit", "qcom,msm8998";
> +       chassis-type = "handset";
> +       /* Required for bootloader to select correct board */
> +       qcom,board-id = <30 0>;
> +
> +       reserved-memory {
> +               /*
> +                * The following memory regions on downstream are "dynamically allocated"
> +                * but given the same addresses every time. Hard code them as these addresses
> +                * are where the Xiaomi signed firmware expects them to be.
> +                */
> +               ipa_fws_region: ipa@f7800000 {
> +                       compatible = "shared-dma-pool";
> +                       reg = <0x0 0xf7800000 0x0 0x5000>;
> +                       no-map;
> +               };
> +
> +               zap_shader_region: gpu@f7900000 {
> +                       compatible = "shared-dma-pool";
> +                       reg = <0x0 0xf7900000 0x0 0x2000>;
> +                       no-map;
> +               };
> +
> +               mpss_mem: memory@8d000000 {
> +                       reg = <0x0 0x8d000000 0x0 0x7000000>;
> +                       no-map;
> +               };
> +
> +               venus_mem: memory@94000000 {
> +                       reg = <0x0 0x94000000 0x0 0x500000>;
> +                       no-map;
> +               };
> +
> +               mba_mem: memory@94500000 {
> +                       reg = <0x0 0x94500000 0x0 0x200000>;
> +                       no-map;
> +               };
> +
> +               slpi_mem: memory@94700000 {
> +                       reg = <0x0 0x94700000 0x0 0x10000>;
> +                       no-map;
> +               };
> +
> +               ipa_fw_mem: memory@95600000 {
> +                       reg = <0x0 0x95600000 0x0 0x10000>;
> +                       no-map;
> +               };
> +
> +               ipa_gsi_mem: memory@95610000 {
> +                       reg = <0x0 0x95610000 0x0 0x5000>;
> +                       no-map;
> +               };
> +
> +               gpu_mem: memory@95615000 {
> +                       reg = <0x0 0x95615000 0x0 0x100000>;
> +                       no-map;
> +               };
> +
> +               wlan_msa_mem: memory@95715000 {
> +                       reg = <0x0 0x95715000 0x0 0x100000>;
> +                       no-map;
> +               };
> +       };
> +
> +       gpio-keys {
> +               compatible = "gpio-keys";
> +               label = "Volume buttons";
> +               autorepeat;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&vol_up_key_default>;
> +
> +               key-vol-up {
> +                       label = "Volume up";
> +                       gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> +                       linux,code = <KEY_VOLUMEUP>;
> +                       debounce-interval = <15>;
> +                       wakeup-source;
> +               };
> +       };
> +
> +       gpio-hall-sensor {
> +               compatible = "gpio-keys";
> +               label = "Hall effect sensor";
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&hall_sensor_default_state>;
> +
> +               event-hall-sensor {
> +                       label = "Hall Effect Sensor";
> +                       gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
> +                       linux,input-type = <EV_SW>;
> +                       linux,code = <SW_LID>;
> +                       linux,can-disable;
> +                       wakeup-source;
> +               };
> +       };
> +
> +       vph_pwr: vph-pwr-regulator {
> +               compatible = "regulator-fixed";
> +               regulator-name = "vph_pwr";
> +               regulator-min-microvolt = <3700000>;
> +               regulator-max-microvolt = <3700000>;
> +               regulator-always-on;
> +               regulator-boot-on;
> +       };
> +
> +       disp_vddts_vreg: disp-vddts-regulator {
> +               compatible = "regulator-fixed";
> +               regulator-name = "disp-vddts-regulator";
> +               gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
> +               enable-active-high;
> +               regulator-boot-on;
> +       };
> +};
> +
> +&blsp1_i2c5 {
> +       pinctrl-names = "default", "sleep";
> +
> +       touchscreen@20 {
> +               compatible = "syna,rmi4-i2c";
> +               reg = <0x20>;
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               interrupt-parent = <&tlmm>;
> +               interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
> +
> +               pinctrl-names = "default", "sleep";
> +               pinctrl-0 = <&ts_active_state>;
> +               pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
> +
> +               vdd-supply = <&disp_vddts_vreg>;
> +               vio-supply = <&vreg_l6a_1p8>;
> +
> +               syna,reset-delay-ms = <20>;
> +               syna,startup-delay-ms = <20>;
> +
> +               rmi4-f01@1 {
> +                       reg = <0x01>;
> +                       syna,nosleep-mode = <1>;
> +               };
> +
> +               rmi4-f12@12 {
> +                       reg = <0x12>;
> +                       touchscreen-x-mm = <64>;
> +                       touchscreen-y-mm = <114>;
> +                       syna,sensor-type = <1>;
> +                       syna,rezero-wait-ms = <20>;
> +               };
> +
> +               rmi4-f1a@1a {
> +                       reg = <0x1a>;
> +                       syna,codes = <KEY_BACK KEY_APPSELECT>;
> +               };
> +       };
> +       status = "okay";
> +};
> +
> +&blsp1_i2c5_sleep {
> +       /delete-property/ bias-pull-up;
> +       bias-disable;
> +};
> +
> +&blsp1_uart3 {
> +       bluetooth {
> +               compatible = "qcom,wcn3990-bt";
> +
> +               vddio-supply = <&vreg_s4a_1p8>;
> +               vddxo-supply = <&vreg_l7a_1p8>;
> +               vddrf-supply = <&vreg_l17a_1p3>;
> +               vddch0-supply = <&vreg_l25a_3p3>;
> +               max-speed = <3200000>;
> +       };
> +       status = "okay";
> +};
> +
> +&blsp1_uart3_on {
> +       rx {
> +               /delete-property/ bias-disable;
> +               /*
> +                * Configure a pull-up on 46 (RX). This is needed to
> +                * avoid garbage data when the TX pin of the Bluetooth
> +                * module is in tri-state (module powered off or not
> +                * driving the signal yet).
> +                */
> +               bias-pull-up;
> +       };
> +
> +       cts {
> +               /delete-property/ bias-disable;
> +               /*
> +                * Configure a pull-down on 47 (CTS) to match the pull
> +                * of the Bluetooth module.
> +                */
> +               bias-pull-down;
> +       };
> +};
> +
> +&blsp2_uart1 {
> +       status = "okay";
> +};
> +
> +&pm8005_regulators {
> +       compatible = "qcom,pm8005-regulators";
> +
> +       vdd_s1-supply = <&vph_pwr>;
> +
> +       pm8005_s1: s1 { /* VDD_GFX supply */
> +               regulator-min-microvolt = <524000>;
> +               regulator-max-microvolt = <1100000>;
> +               regulator-enable-ramp-delay = <500>;
> +
> +               /* hack until we rig up the gpu consumer */
> +               regulator-always-on;
> +       };
> +};
> +
> +&pm8998_gpio {
> +       vol_up_key_default: vol-up-key-default-state {
> +               pins = "gpio6";
> +               function = "normal";
> +               bias-pull-up;
> +               input-enable;
> +               qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> +       };
> +
> +       audio_mclk_pin: audio-mclk-pin-active-state {
> +               pins = "gpio13";
> +               function = "func2";
> +               power-source = <0>;
> +       };
> +};
> +
> +&qusb2phy {
> +       vdda-pll-supply = <&vreg_l12a_1p8>;
> +       vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +       status = "okay";
> +};
> +
> +&rpm_requests {
> +       regulators-0 {
> +               compatible = "qcom,rpm-pm8998-regulators";
> +
> +               vdd_s1-supply = <&vph_pwr>;
> +               vdd_s2-supply = <&vph_pwr>;
> +               vdd_s3-supply = <&vph_pwr>;
> +               vdd_s4-supply = <&vph_pwr>;
> +               vdd_s5-supply = <&vph_pwr>;
> +               vdd_s6-supply = <&vph_pwr>;
> +               vdd_s7-supply = <&vph_pwr>;
> +               vdd_s8-supply = <&vph_pwr>;
> +               vdd_s9-supply = <&vph_pwr>;
> +               vdd_s10-supply = <&vph_pwr>;
> +               vdd_s11-supply = <&vph_pwr>;
> +               vdd_s12-supply = <&vph_pwr>;
> +               vdd_s13-supply = <&vph_pwr>;
> +               vdd_l1_l27-supply = <&vreg_s7a_1p025>;
> +               vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
> +               vdd_l3_l11-supply = <&vreg_s7a_1p025>;
> +               vdd_l4_l5-supply = <&vreg_s7a_1p025>;
> +               vdd_l6-supply = <&vreg_s5a_2p04>;
> +               vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
> +               vdd_l9-supply = <&vreg_bob>;
> +               vdd_l10_l23_l25-supply = <&vreg_bob>;
> +               vdd_l13_l19_l21-supply = <&vreg_bob>;
> +               vdd_l16_l28-supply = <&vreg_bob>;
> +               vdd_l18_l22-supply = <&vreg_bob>;
> +               vdd_l20_l24-supply = <&vreg_bob>;
> +               vdd_l26-supply = <&vreg_s3a_1p35>;
> +               vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
> +
> +               vreg_s3a_1p35: s3 {
> +                       regulator-min-microvolt = <1352000>;
> +                       regulator-max-microvolt = <1352000>;
> +               };
> +
> +               vreg_s4a_1p8: s4 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +                       regulator-allow-set-load;
> +               };
> +
> +               vreg_s5a_2p04: s5 {
> +                       regulator-min-microvolt = <1904000>;
> +                       regulator-max-microvolt = <2040000>;
> +               };
> +
> +               vreg_s7a_1p025: s7 {
> +                       regulator-min-microvolt = <900000>;
> +                       regulator-max-microvolt = <1028000>;
> +               };
> +
> +               vreg_l1a_0p875: l1 {
> +                       regulator-min-microvolt = <880000>;
> +                       regulator-max-microvolt = <880000>;
> +               };
> +
> +               vreg_l2a_1p2: l2 {
> +                       regulator-min-microvolt = <1200000>;
> +                       regulator-max-microvolt = <1200000>;
> +               };
> +
> +               vreg_l3a_1p0: l3 {
> +                       regulator-min-microvolt = <1000000>;
> +                       regulator-max-microvolt = <1000000>;
> +               };
> +
> +               vreg_l5a_0p8: l5 {
> +                       regulator-min-microvolt = <800000>;
> +                       regulator-max-microvolt = <800000>;
> +               };
> +
> +               vreg_l6a_1p8: l6 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l7a_1p8: l7 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l8a_1p2: l8 {
> +                       regulator-min-microvolt = <1200000>;
> +                       regulator-max-microvolt = <1200000>;
> +               };
> +
> +               vreg_l9a_1p8: l9 {
> +                       regulator-min-microvolt = <1808000>;
> +                       regulator-max-microvolt = <2960000>;
> +               };
> +
> +               vreg_l10a_1p8: l10 {
> +                       regulator-min-microvolt = <1808000>;
> +                       regulator-max-microvolt = <2960000>;
> +               };
> +
> +               vreg_l11a_1p0: l11 {
> +                       regulator-min-microvolt = <1000000>;
> +                       regulator-max-microvolt = <1000000>;
> +               };
> +
> +               vreg_l12a_1p8: l12 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l13a_2p95: l13 {
> +                       regulator-min-microvolt = <1808000>;
> +                       regulator-max-microvolt = <2960000>;
> +               };
> +
> +               vreg_l14a_1p8: l14 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l15a_1p8: l15 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l16a_2p7: l16 {
> +                       regulator-min-microvolt = <2704000>;
> +                       regulator-max-microvolt = <2704000>;
> +               };
> +
> +               vreg_l17a_1p3: l17 {
> +                       regulator-min-microvolt = <1304000>;
> +                       regulator-max-microvolt = <1304000>;
> +               };
> +
> +               vreg_l18a_2p7: l18 {
> +                       regulator-min-microvolt = <2704000>;
> +                       regulator-max-microvolt = <2704000>;
> +               };
> +
> +               vreg_l19a_3p0: l19 {
> +                       regulator-min-microvolt = <3008000>;
> +                       regulator-max-microvolt = <3008000>;
> +               };
> +
> +               vreg_l20a_2p95: l20 {
> +                       regulator-min-microvolt = <2960000>;
> +                       regulator-max-microvolt = <2960000>;
> +                       regulator-allow-set-load;
> +               };
> +
> +               vreg_l21a_2p95: l21 {
> +                       regulator-min-microvolt = <2960000>;
> +                       regulator-max-microvolt = <2960000>;
> +                       regulator-system-load = <800000>;
> +                       regulator-allow-set-load;
> +               };
> +
> +               vreg_l22a_2p85: l22 {
> +                       regulator-min-microvolt = <2864000>;
> +                       regulator-max-microvolt = <2864000>;
> +               };
> +
> +               vreg_l23a_3p3: l23 {
> +                       regulator-min-microvolt = <3312000>;
> +                       regulator-max-microvolt = <3312000>;
> +               };
> +
> +               vreg_l24a_3p075: l24 {
> +                       regulator-min-microvolt = <3088000>;
> +                       regulator-max-microvolt = <3088000>;
> +               };
> +
> +               vreg_l25a_3p3: l25 {
> +                       regulator-min-microvolt = <3104000>;
> +                       regulator-max-microvolt = <3312000>;
> +               };
> +
> +               vreg_l26a_1p2: l26 {
> +                       regulator-min-microvolt = <1200000>;
> +                       regulator-max-microvolt = <1200000>;
> +                       regulator-allow-set-load;
> +               };
> +
> +               vreg_l28_3p0: l28 {
> +                       regulator-min-microvolt = <3008000>;
> +                       regulator-max-microvolt = <3008000>;
> +               };
> +
> +               vreg_lvs1a_1p8: lvs1 { };
> +
> +               vreg_lvs2a_1p8: lvs2 { };
> +       };
> +
> +       regulators-1 {
> +               compatible = "qcom,rpm-pmi8998-regulators";
> +
> +               vdd_bob-supply = <&vph_pwr>;
> +
> +               vreg_bob: bob {
> +                       regulator-min-microvolt = <3312000>;
> +                       regulator-max-microvolt = <3600000>;
> +               };
> +       };
> +};
> +
> +&tlmm {
> +       gpio-reserved-ranges = <0 4>, <81 4>;
> +
> +       cci1_default_state: cci1-default-state {
> +               pins = "gpio19", "gpio20";
> +               function = "cci_i2c";
> +               bias-disable;
> +               drive-strength = <2>;
> +       };
> +
> +       cdc_reset_n_state: cdc-reset-n-state {
> +               pins = "gpio64";
> +               function = "gpio";
> +               bias-pull-down;
> +               drive-strength = <16>;
> +               output-high;
> +       };
> +
> +       hall_sensor_default_state: hall-sensor-default-state {
> +               pins = "gpio124";
> +               function = "gpio";
> +               drive-strength = <2>;
> +               bias-disable;
> +               input-enable;
> +       };
> +
> +       mdss_dsi_active_state: mdss-dsi-active-state {
> +               pins = "gpio94";
> +               function = "gpio";
> +               drive-strength = <8>;
> +               bias-disable;
> +       };
> +
> +       mdss_dsi_suspend_state: mdss-dsi-suspend-state {
> +               pins = "gpio94";
> +               function = "gpio";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       mdss_te_active_state: mdss-te-active-state {
> +               pins = "gpio10";
> +               function = "mdp_vsync_a";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       mdss_te_suspend_state: mdss-te-suspend-state {
> +               pins = "gpio10";
> +               function = "mdp_vsync_a";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       msm_mclk0_active_state: msm-mclk0-active-state {
> +               pins = "gpio13";
> +               function = "cam_mclk";
> +               drive-strength = <2>;
> +               bias-disable;
> +       };
> +
> +       msm_mclk0_suspend_state: msm-mclk0-suspend-state {
> +               pins = "gpio13";
> +               function = "cam_mclk";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       msm_mclk1_active_state: msm-mclk1-active-state {
> +               pins = "gpio14";
> +               function = "cam_mclk";
> +               drive-strength = <2>;
> +               bias-disable;
> +       };
> +
> +       msm_mclk1_suspend_state: msm-mclk1-suspend-state {
> +               pins = "gpio14";
> +               function = "cam_mclk";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       nfc_int_active_state: nfc-int-active-state {
> +               pins = "gpio92";
> +               function = "gpio";
> +               drive-strength = <6>;
> +               bias-pull-up;
> +       };
> +
> +       nfc_int_suspend_state: nfc-int-suspend-state {
> +               pins = "gpio92";
> +               function = "gpio";
> +               drive-strength = <6>;
> +               bias-pull-up;
> +       };
> +
> +       nfc_enable_active_state: nfc-enable-active-state {
> +               pins = "gpio12", "gpio116";
> +               function = "gpio";
> +               drive-strength = <6>;
> +               bias-pull-up;
> +       };
> +
> +       nfc_enable_suspend_state: nfc-enable-suspend-state {
> +               pins = "gpio12", "gpio116";
> +               function = "gpio";
> +               drive-strength = <6>;
> +               bias-disable;
> +       };
> +
> +       ts_active_state: ts-active-state {
> +               pins = "gpio89", "gpio125";
> +               function = "gpio";
> +               drive-strength = <16>;
> +               bias-pull-up;
> +               input-enable;
> +       };
> +
> +       ts_int_suspend_state: ts-int-suspend-state {
> +               pins = "gpio125";
> +               function = "gpio";
> +               drive-strength = <2>;
> +               bias-disable;
> +       };
> +
> +       ts_reset_suspend_state: ts-reset-suspend-state {
> +               pins = "gpio89";
> +               function = "gpio";
> +               drive-strength = <2>;
> +               bias-disable;
> +       };
> +
> +       wcd_int_n_state: wcd-int-n-state {
> +               pins = "gpio54";
> +               function = "gpio";
> +               bias-pull-down;
> +               drive-strength = <2>;
> +               input-enable;
> +       };
> +
> +       wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state {
> +               pins = "gpio65";
> +               function = "gpio";
> +               bias-disable;
> +               drive-strength = <2>;
> +               output-low;
> +       };
> +
> +       wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state {
> +               pins = "gpio66";
> +               function = "gpio";
> +               bias-disable;
> +               drive-strength = <2>;
> +               output-low;
> +       };
> +};
> +
> +&pm8998_resin {
> +       linux,code = <KEY_VOLUMEDOWN>;
> +};
> +
> +&ufshc {
> +       vcc-supply = <&vreg_l20a_2p95>;
> +       vccq-supply = <&vreg_l26a_1p2>;
> +       vccq2-supply = <&vreg_s4a_1p8>;
> +       vcc-max-microamp = <750000>;
> +       vccq-max-microamp = <560000>;
> +       vccq2-max-microamp = <750000>;
> +       status = "okay";
> +};
> +
> +&ufsphy {
> +       vdda-phy-supply = <&vreg_l1a_0p875>;
> +       vdda-pll-supply = <&vreg_l2a_1p2>;
> +       vddp-ref-clk-supply = <&vreg_l26a_1p2>;
> +       status = "okay";
> +};
> +
> +&usb3 {
> +       /* Disable USB3 clock requirement as the device only supports USB2 */
> +       qcom,select-utmi-as-pipe-clk;
> +       status = "okay";
> +};
> +
> +&usb3_dwc3 {
> +       /* Drop the unused USB 3 PHY */
> +       phys = <&qusb2phy>;
> +       phy-names = "usb2-phy";
> +
> +       /* Fastest mode for USB 2 */
> +       maximum-speed = "high-speed";
> +
> +       /* Force to peripheral until we can switch modes */
> +       dr_mode = "peripheral";
> +};
> +
> +&wifi {
> +       vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
> +       vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> +       vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
> +       vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
> +       status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
> index d09f2954b6f9..7929fa64e1ef 100644
> --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
> @@ -52,6 +52,14 @@ pm8998_pwrkey: pwrkey {
>                                 bias-pull-up;
>                                 linux,code = <KEY_POWER>;
>                         };
> +
> +                       pm8998_resin: resin {
> +                               compatible = "qcom,pm8941-resin";
> +                               bias-pull-up;
> +                               interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> +                               debounce = <15625>;
> +                               status = "disabled";
> +                       };
>                 };
>
>                 pm8998_temp: temp-alarm@2400 {
> --
> 2.30.2
>
Dzmitry Sankouski Oct. 5, 2022, 7:13 p.m. UTC | #2
compilation fails for this patch version, please, heed on to version 7 series

ср, 5 окт. 2022 г. в 21:15, Dzmitry Sankouski <dsankouski@gmail.com>:
>
> New device support - Xiaomi Mi6 phone
>
> What works:
> - storage
> - usb
> - power regulators
>
> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/msm8998-xiaomi-sagit.dts    | 681 ++++++++++++++++++
>  arch/arm64/boot/dts/qcom/pm8998.dtsi          |   8 +
>  3 files changed, 690 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 1d86a33de528..0460aabf1b59 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM)       += msm8998-oneplus-dumpling.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-lilac.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-maple.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-poplar.dtb
> +dtb-$(CONFIG_ARCH_QCOM)        += msm8998-xiaomi-sagit.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += qcs404-evb-1000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += qcs404-evb-4000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += qrb5165-rb5.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> new file mode 100644
> index 000000000000..e44f6a745a2c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
> @@ -0,0 +1,681 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
> + *
> + * Copyright (c) 2022, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
> + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "msm8998.dtsi"
> +#include "pm8005.dtsi"
> +#include "pm8998.dtsi"
> +#include "pmi8998.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +
> +/*
> + * Delete following upstream (msm8998.dtsi) reserved
> + * memory mappings which are different in this device.
> + */
> +/delete-node/ &mpss_mem;
> +/delete-node/ &venus_mem;
> +/delete-node/ &mba_mem;
> +/delete-node/ &slpi_mem;
> +/delete-node/ &ipa_fw_mem;
> +/delete-node/ &ipa_gsi_mem;
> +/delete-node/ &gpu_mem;
> +/delete-node/ &wlan_msa_mem;
> +
> +/ {
> +       model = "Xiaomi Mi 6";
> +       compatible = "xiaomi,sagit", "qcom,msm8998";
> +       chassis-type = "handset";
> +       /* Required for bootloader to select correct board */
> +       qcom,board-id = <30 0>;
> +
> +       reserved-memory {
> +               /*
> +                * The following memory regions on downstream are "dynamically allocated"
> +                * but given the same addresses every time. Hard code them as these addresses
> +                * are where the Xiaomi signed firmware expects them to be.
> +                */
> +               ipa_fws_region: ipa@f7800000 {
> +                       compatible = "shared-dma-pool";
> +                       reg = <0x0 0xf7800000 0x0 0x5000>;
> +                       no-map;
> +               };
> +
> +               zap_shader_region: gpu@f7900000 {
> +                       compatible = "shared-dma-pool";
> +                       reg = <0x0 0xf7900000 0x0 0x2000>;
> +                       no-map;
> +               };
> +
> +               mpss_mem: memory@8d000000 {
> +                       reg = <0x0 0x8d000000 0x0 0x7000000>;
> +                       no-map;
> +               };
> +
> +               venus_mem: memory@94000000 {
> +                       reg = <0x0 0x94000000 0x0 0x500000>;
> +                       no-map;
> +               };
> +
> +               mba_mem: memory@94500000 {
> +                       reg = <0x0 0x94500000 0x0 0x200000>;
> +                       no-map;
> +               };
> +
> +               slpi_mem: memory@94700000 {
> +                       reg = <0x0 0x94700000 0x0 0x10000>;
> +                       no-map;
> +               };
> +
> +               ipa_fw_mem: memory@95600000 {
> +                       reg = <0x0 0x95600000 0x0 0x10000>;
> +                       no-map;
> +               };
> +
> +               ipa_gsi_mem: memory@95610000 {
> +                       reg = <0x0 0x95610000 0x0 0x5000>;
> +                       no-map;
> +               };
> +
> +               gpu_mem: memory@95615000 {
> +                       reg = <0x0 0x95615000 0x0 0x100000>;
> +                       no-map;
> +               };
> +
> +               wlan_msa_mem: memory@95715000 {
> +                       reg = <0x0 0x95715000 0x0 0x100000>;
> +                       no-map;
> +               };
> +       };
> +
> +       gpio-keys {
> +               compatible = "gpio-keys";
> +               label = "Volume buttons";
> +               autorepeat;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&vol_up_key_default>;
> +
> +               key-vol-up {
> +                       label = "Volume up";
> +                       gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> +                       linux,code = <KEY_VOLUMEUP>;
> +                       debounce-interval = <15>;
> +                       wakeup-source;
> +               };
> +       };
> +
> +       gpio-hall-sensor {
> +               compatible = "gpio-keys";
> +               label = "Hall effect sensor";
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&hall_sensor_default_state>;
> +
> +               event-hall-sensor {
> +                       label = "Hall Effect Sensor";
> +                       gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
> +                       linux,input-type = <EV_SW>;
> +                       linux,code = <SW_LID>;
> +                       linux,can-disable;
> +                       wakeup-source;
> +               };
> +       };
> +
> +       vph_pwr: vph-pwr-regulator {
> +               compatible = "regulator-fixed";
> +               regulator-name = "vph_pwr";
> +               regulator-min-microvolt = <3700000>;
> +               regulator-max-microvolt = <3700000>;
> +               regulator-always-on;
> +               regulator-boot-on;
> +       };
> +
> +       disp_vddts_vreg: disp-vddts-regulator {
> +               compatible = "regulator-fixed";
> +               regulator-name = "disp-vddts-regulator";
> +               gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
> +               enable-active-high;
> +               regulator-boot-on;
> +       };
> +};
> +
> +&blsp1_i2c5 {
> +       pinctrl-names = "default", "sleep";
> +
> +       touchscreen@20 {
> +               compatible = "syna,rmi4-i2c";
> +               reg = <0x20>;
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               interrupt-parent = <&tlmm>;
> +               interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
> +
> +               pinctrl-names = "default", "sleep";
> +               pinctrl-0 = <&ts_active_state>;
> +               pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
> +
> +               vdd-supply = <&disp_vddts_vreg>;
> +               vio-supply = <&vreg_l6a_1p8>;
> +
> +               syna,reset-delay-ms = <20>;
> +               syna,startup-delay-ms = <20>;
> +
> +               rmi4-f01@1 {
> +                       reg = <0x01>;
> +                       syna,nosleep-mode = <1>;
> +               };
> +
> +               rmi4-f12@12 {
> +                       reg = <0x12>;
> +                       touchscreen-x-mm = <64>;
> +                       touchscreen-y-mm = <114>;
> +                       syna,sensor-type = <1>;
> +                       syna,rezero-wait-ms = <20>;
> +               };
> +
> +               rmi4-f1a@1a {
> +                       reg = <0x1a>;
> +                       syna,codes = <KEY_BACK KEY_APPSELECT>;
> +               };
> +       };
> +       status = "okay";
> +};
> +
> +&blsp1_i2c5_sleep {
> +       /delete-property/ bias-pull-up;
> +       bias-disable;
> +};
> +
> +&blsp1_uart3 {
> +       bluetooth {
> +               compatible = "qcom,wcn3990-bt";
> +
> +               vddio-supply = <&vreg_s4a_1p8>;
> +               vddxo-supply = <&vreg_l7a_1p8>;
> +               vddrf-supply = <&vreg_l17a_1p3>;
> +               vddch0-supply = <&vreg_l25a_3p3>;
> +               max-speed = <3200000>;
> +       };
> +       status = "okay";
> +};
> +
> +&blsp1_uart3_on {
> +       rx {
> +               /delete-property/ bias-disable;
> +               /*
> +                * Configure a pull-up on 46 (RX). This is needed to
> +                * avoid garbage data when the TX pin of the Bluetooth
> +                * module is in tri-state (module powered off or not
> +                * driving the signal yet).
> +                */
> +               bias-pull-up;
> +       };
> +
> +       cts {
> +               /delete-property/ bias-disable;
> +               /*
> +                * Configure a pull-down on 47 (CTS) to match the pull
> +                * of the Bluetooth module.
> +                */
> +               bias-pull-down;
> +       };
> +};
> +
> +&blsp2_uart1 {
> +       status = "okay";
> +};
> +
> +&pm8005_regulators {
> +       compatible = "qcom,pm8005-regulators";
> +
> +       vdd_s1-supply = <&vph_pwr>;
> +
> +       pm8005_s1: s1 { /* VDD_GFX supply */
> +               regulator-min-microvolt = <524000>;
> +               regulator-max-microvolt = <1100000>;
> +               regulator-enable-ramp-delay = <500>;
> +
> +               /* hack until we rig up the gpu consumer */
> +               regulator-always-on;
> +       };
> +};
> +
> +&pm8998_gpio {
> +       vol_up_key_default: vol-up-key-default-state {
> +               pins = "gpio6";
> +               function = "normal";
> +               bias-pull-up;
> +               input-enable;
> +               qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> +       };
> +
> +       audio_mclk_pin: audio-mclk-pin-active-state {
> +               pins = "gpio13";
> +               function = "func2";
> +               power-source = <0>;
> +       };
> +};
> +
> +&qusb2phy {
> +       vdda-pll-supply = <&vreg_l12a_1p8>;
> +       vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +       status = "okay";
> +};
> +
> +&rpm_requests {
> +       regulators-0 {
> +               compatible = "qcom,rpm-pm8998-regulators";
> +
> +               vdd_s1-supply = <&vph_pwr>;
> +               vdd_s2-supply = <&vph_pwr>;
> +               vdd_s3-supply = <&vph_pwr>;
> +               vdd_s4-supply = <&vph_pwr>;
> +               vdd_s5-supply = <&vph_pwr>;
> +               vdd_s6-supply = <&vph_pwr>;
> +               vdd_s7-supply = <&vph_pwr>;
> +               vdd_s8-supply = <&vph_pwr>;
> +               vdd_s9-supply = <&vph_pwr>;
> +               vdd_s10-supply = <&vph_pwr>;
> +               vdd_s11-supply = <&vph_pwr>;
> +               vdd_s12-supply = <&vph_pwr>;
> +               vdd_s13-supply = <&vph_pwr>;
> +               vdd_l1_l27-supply = <&vreg_s7a_1p025>;
> +               vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
> +               vdd_l3_l11-supply = <&vreg_s7a_1p025>;
> +               vdd_l4_l5-supply = <&vreg_s7a_1p025>;
> +               vdd_l6-supply = <&vreg_s5a_2p04>;
> +               vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
> +               vdd_l9-supply = <&vreg_bob>;
> +               vdd_l10_l23_l25-supply = <&vreg_bob>;
> +               vdd_l13_l19_l21-supply = <&vreg_bob>;
> +               vdd_l16_l28-supply = <&vreg_bob>;
> +               vdd_l18_l22-supply = <&vreg_bob>;
> +               vdd_l20_l24-supply = <&vreg_bob>;
> +               vdd_l26-supply = <&vreg_s3a_1p35>;
> +               vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
> +
> +               vreg_s3a_1p35: s3 {
> +                       regulator-min-microvolt = <1352000>;
> +                       regulator-max-microvolt = <1352000>;
> +               };
> +
> +               vreg_s4a_1p8: s4 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +                       regulator-allow-set-load;
> +               };
> +
> +               vreg_s5a_2p04: s5 {
> +                       regulator-min-microvolt = <1904000>;
> +                       regulator-max-microvolt = <2040000>;
> +               };
> +
> +               vreg_s7a_1p025: s7 {
> +                       regulator-min-microvolt = <900000>;
> +                       regulator-max-microvolt = <1028000>;
> +               };
> +
> +               vreg_l1a_0p875: l1 {
> +                       regulator-min-microvolt = <880000>;
> +                       regulator-max-microvolt = <880000>;
> +               };
> +
> +               vreg_l2a_1p2: l2 {
> +                       regulator-min-microvolt = <1200000>;
> +                       regulator-max-microvolt = <1200000>;
> +               };
> +
> +               vreg_l3a_1p0: l3 {
> +                       regulator-min-microvolt = <1000000>;
> +                       regulator-max-microvolt = <1000000>;
> +               };
> +
> +               vreg_l5a_0p8: l5 {
> +                       regulator-min-microvolt = <800000>;
> +                       regulator-max-microvolt = <800000>;
> +               };
> +
> +               vreg_l6a_1p8: l6 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l7a_1p8: l7 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l8a_1p2: l8 {
> +                       regulator-min-microvolt = <1200000>;
> +                       regulator-max-microvolt = <1200000>;
> +               };
> +
> +               vreg_l9a_1p8: l9 {
> +                       regulator-min-microvolt = <1808000>;
> +                       regulator-max-microvolt = <2960000>;
> +               };
> +
> +               vreg_l10a_1p8: l10 {
> +                       regulator-min-microvolt = <1808000>;
> +                       regulator-max-microvolt = <2960000>;
> +               };
> +
> +               vreg_l11a_1p0: l11 {
> +                       regulator-min-microvolt = <1000000>;
> +                       regulator-max-microvolt = <1000000>;
> +               };
> +
> +               vreg_l12a_1p8: l12 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l13a_2p95: l13 {
> +                       regulator-min-microvolt = <1808000>;
> +                       regulator-max-microvolt = <2960000>;
> +               };
> +
> +               vreg_l14a_1p8: l14 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l15a_1p8: l15 {
> +                       regulator-min-microvolt = <1800000>;
> +                       regulator-max-microvolt = <1800000>;
> +               };
> +
> +               vreg_l16a_2p7: l16 {
> +                       regulator-min-microvolt = <2704000>;
> +                       regulator-max-microvolt = <2704000>;
> +               };
> +
> +               vreg_l17a_1p3: l17 {
> +                       regulator-min-microvolt = <1304000>;
> +                       regulator-max-microvolt = <1304000>;
> +               };
> +
> +               vreg_l18a_2p7: l18 {
> +                       regulator-min-microvolt = <2704000>;
> +                       regulator-max-microvolt = <2704000>;
> +               };
> +
> +               vreg_l19a_3p0: l19 {
> +                       regulator-min-microvolt = <3008000>;
> +                       regulator-max-microvolt = <3008000>;
> +               };
> +
> +               vreg_l20a_2p95: l20 {
> +                       regulator-min-microvolt = <2960000>;
> +                       regulator-max-microvolt = <2960000>;
> +                       regulator-allow-set-load;
> +               };
> +
> +               vreg_l21a_2p95: l21 {
> +                       regulator-min-microvolt = <2960000>;
> +                       regulator-max-microvolt = <2960000>;
> +                       regulator-system-load = <800000>;
> +                       regulator-allow-set-load;
> +               };
> +
> +               vreg_l22a_2p85: l22 {
> +                       regulator-min-microvolt = <2864000>;
> +                       regulator-max-microvolt = <2864000>;
> +               };
> +
> +               vreg_l23a_3p3: l23 {
> +                       regulator-min-microvolt = <3312000>;
> +                       regulator-max-microvolt = <3312000>;
> +               };
> +
> +               vreg_l24a_3p075: l24 {
> +                       regulator-min-microvolt = <3088000>;
> +                       regulator-max-microvolt = <3088000>;
> +               };
> +
> +               vreg_l25a_3p3: l25 {
> +                       regulator-min-microvolt = <3104000>;
> +                       regulator-max-microvolt = <3312000>;
> +               };
> +
> +               vreg_l26a_1p2: l26 {
> +                       regulator-min-microvolt = <1200000>;
> +                       regulator-max-microvolt = <1200000>;
> +                       regulator-allow-set-load;
> +               };
> +
> +               vreg_l28_3p0: l28 {
> +                       regulator-min-microvolt = <3008000>;
> +                       regulator-max-microvolt = <3008000>;
> +               };
> +
> +               vreg_lvs1a_1p8: lvs1 { };
> +
> +               vreg_lvs2a_1p8: lvs2 { };
> +       };
> +
> +       regulators-1 {
> +               compatible = "qcom,rpm-pmi8998-regulators";
> +
> +               vdd_bob-supply = <&vph_pwr>;
> +
> +               vreg_bob: bob {
> +                       regulator-min-microvolt = <3312000>;
> +                       regulator-max-microvolt = <3600000>;
> +               };
> +       };
> +};
> +
> +&tlmm {
> +       gpio-reserved-ranges = <0 4>, <81 4>;
> +
> +       cci1_default_state: cci1-default-state {
> +               pins = "gpio19", "gpio20";
> +               function = "cci_i2c";
> +               bias-disable;
> +               drive-strength = <2>;
> +       };
> +
> +       cdc_reset_n_state: cdc-reset-n-state {
> +               pins = "gpio64";
> +               function = "gpio";
> +               bias-pull-down;
> +               drive-strength = <16>;
> +               output-high;
> +       };
> +
> +       hall_sensor_default_state: hall-sensor-default-state {
> +               pins = "gpio124";
> +               function = "gpio";
> +               drive-strength = <2>;
> +               bias-disable;
> +               input-enable;
> +       };
> +
> +       mdss_dsi_active_state: mdss-dsi-active-state {
> +               pins = "gpio94";
> +               function = "gpio";
> +               drive-strength = <8>;
> +               bias-disable;
> +       };
> +
> +       mdss_dsi_suspend_state: mdss-dsi-suspend-state {
> +               pins = "gpio94";
> +               function = "gpio";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       mdss_te_active_state: mdss-te-active-state {
> +               pins = "gpio10";
> +               function = "mdp_vsync_a";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       mdss_te_suspend_state: mdss-te-suspend-state {
> +               pins = "gpio10";
> +               function = "mdp_vsync_a";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       msm_mclk0_active_state: msm-mclk0-active-state {
> +               pins = "gpio13";
> +               function = "cam_mclk";
> +               drive-strength = <2>;
> +               bias-disable;
> +       };
> +
> +       msm_mclk0_suspend_state: msm-mclk0-suspend-state {
> +               pins = "gpio13";
> +               function = "cam_mclk";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       msm_mclk1_active_state: msm-mclk1-active-state {
> +               pins = "gpio14";
> +               function = "cam_mclk";
> +               drive-strength = <2>;
> +               bias-disable;
> +       };
> +
> +       msm_mclk1_suspend_state: msm-mclk1-suspend-state {
> +               pins = "gpio14";
> +               function = "cam_mclk";
> +               drive-strength = <2>;
> +               bias-pull-down;
> +       };
> +
> +       nfc_int_active_state: nfc-int-active-state {
> +               pins = "gpio92";
> +               function = "gpio";
> +               drive-strength = <6>;
> +               bias-pull-up;
> +       };
> +
> +       nfc_int_suspend_state: nfc-int-suspend-state {
> +               pins = "gpio92";
> +               function = "gpio";
> +               drive-strength = <6>;
> +               bias-pull-up;
> +       };
> +
> +       nfc_enable_active_state: nfc-enable-active-state {
> +               pins = "gpio12", "gpio116";
> +               function = "gpio";
> +               drive-strength = <6>;
> +               bias-pull-up;
> +       };
> +
> +       nfc_enable_suspend_state: nfc-enable-suspend-state {
> +               pins = "gpio12", "gpio116";
> +               function = "gpio";
> +               drive-strength = <6>;
> +               bias-disable;
> +       };
> +
> +       ts_active_state: ts-active-state {
> +               pins = "gpio89", "gpio125";
> +               function = "gpio";
> +               drive-strength = <16>;
> +               bias-pull-up;
> +               input-enable;
> +       };
> +
> +       ts_int_suspend_state: ts-int-suspend-state {
> +               pins = "gpio125";
> +               function = "gpio";
> +               drive-strength = <2>;
> +               bias-disable;
> +       };
> +
> +       ts_reset_suspend_state: ts-reset-suspend-state {
> +               pins = "gpio89";
> +               function = "gpio";
> +               drive-strength = <2>;
> +               bias-disable;
> +       };
> +
> +       wcd_int_n_state: wcd-int-n-state {
> +               pins = "gpio54";
> +               function = "gpio";
> +               bias-pull-down;
> +               drive-strength = <2>;
> +               input-enable;
> +       };
> +
> +       wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state {
> +               pins = "gpio65";
> +               function = "gpio";
> +               bias-disable;
> +               drive-strength = <2>;
> +               output-low;
> +       };
> +
> +       wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state {
> +               pins = "gpio66";
> +               function = "gpio";
> +               bias-disable;
> +               drive-strength = <2>;
> +               output-low;
> +       };
> +};
> +
> +&pm8998_resin {
> +       linux,code = <KEY_VOLUMEDOWN>;
> +};
> +
> +&ufshc {
> +       vcc-supply = <&vreg_l20a_2p95>;
> +       vccq-supply = <&vreg_l26a_1p2>;
> +       vccq2-supply = <&vreg_s4a_1p8>;
> +       vcc-max-microamp = <750000>;
> +       vccq-max-microamp = <560000>;
> +       vccq2-max-microamp = <750000>;
> +       status = "okay";
> +};
> +
> +&ufsphy {
> +       vdda-phy-supply = <&vreg_l1a_0p875>;
> +       vdda-pll-supply = <&vreg_l2a_1p2>;
> +       vddp-ref-clk-supply = <&vreg_l26a_1p2>;
> +       status = "okay";
> +};
> +
> +&usb3 {
> +       /* Disable USB3 clock requirement as the device only supports USB2 */
> +       qcom,select-utmi-as-pipe-clk;
> +       status = "okay";
> +};
> +
> +&usb3_dwc3 {
> +       /* Drop the unused USB 3 PHY */
> +       phys = <&qusb2phy>;
> +       phy-names = "usb2-phy";
> +
> +       /* Fastest mode for USB 2 */
> +       maximum-speed = "high-speed";
> +
> +       /* Force to peripheral until we can switch modes */
> +       dr_mode = "peripheral";
> +};
> +
> +&wifi {
> +       vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
> +       vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
> +       vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
> +       vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
> +       status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
> index d09f2954b6f9..7929fa64e1ef 100644
> --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
> @@ -52,6 +52,14 @@ pm8998_pwrkey: pwrkey {
>                                 bias-pull-up;
>                                 linux,code = <KEY_POWER>;
>                         };
> +
> +                       pm8998_resin: resin {
> +                               compatible = "qcom,pm8941-resin";
> +                               bias-pull-up;
> +                               interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> +                               debounce = <15625>;
> +                               status = "disabled";
> +                       };
>                 };
>
>                 pm8998_temp: temp-alarm@2400 {
> --
> 2.30.2
>
Konrad Dybcio Oct. 7, 2022, 7:34 p.m. UTC | #3
On 5.10.2022 20:30, Dzmitry Sankouski wrote:
> Here is changelogs:
> 
> Changes for v2:
> - remove memory nodes before redefining
> - add board compatible to schema
> - remove board msm-id, add chassis type
> - remove common dtsi
> - move resin to pm8998 dtsi file
> - dts formatting
> - unsupported properties removed
> - add copyright
> - rebase on latest master(6.0.0-rc6)
> Changes for v3:
> - regulators nodes renamed to match pattern 'regulators-[01]'
> - duplicate cci1-default node deleted
> - add state suffix to '.*(active|suspend|default)' pinctrl
> - rebase on latest master(6.0.0)
> Changes for v4:
> - fix dts compilation errors(rename pinctrl label usages)
> Changes for v5:
> - use pm8005_regulators label
> Changes for v6:
> - add state suffix to all pinctrl
> - move status nodes to last position
> - disable resin node by default
> - move the debounce param to pm8998.dtsi file
> - place this patch after dt-binding patch
> 
> 
> ср, 5 окт. 2022 г. в 21:15, Dzmitry Sankouski <dsankouski@gmail.com>:
>>
>> New device support - Xiaomi Mi6 phone
>>
>> What works:
>> - storage
>> - usb
>> - power regulators
>>
>> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
>> ---
>>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>>  .../boot/dts/qcom/msm8998-xiaomi-sagit.dts    | 681 ++++++++++++++++++
>>  arch/arm64/boot/dts/qcom/pm8998.dtsi          |   8 +
>>  3 files changed, 690 insertions(+)
>>  create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index 1d86a33de528..0460aabf1b59 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM)       += msm8998-oneplus-dumpling.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-lilac.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-maple.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)        += msm8998-sony-xperia-yoshino-poplar.dtb
>> +dtb-$(CONFIG_ARCH_QCOM)        += msm8998-xiaomi-sagit.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)        += qcs404-evb-1000.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)        += qcs404-evb-4000.dtb
>>  dtb-$(CONFIG_ARCH_QCOM)        += qrb5165-rb5.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>> new file mode 100644
>> index 000000000000..e44f6a745a2c
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>> @@ -0,0 +1,681 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
>> + *
>> + * Copyright (c) 2022, The Linux Foundation. All rights reserved.
>> + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
>> + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "msm8998.dtsi"
>> +#include "pm8005.dtsi"
>> +#include "pm8998.dtsi"
>> +#include "pmi8998.dtsi"
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/leds/common.h>
>> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
>> +
>> +/*
>> + * Delete following upstream (msm8998.dtsi) reserved
>> + * memory mappings which are different in this device.
>> + */
>> +/delete-node/ &mpss_mem;
>> +/delete-node/ &venus_mem;
>> +/delete-node/ &mba_mem;
>> +/delete-node/ &slpi_mem;
>> +/delete-node/ &ipa_fw_mem;
>> +/delete-node/ &ipa_gsi_mem;
>> +/delete-node/ &gpu_mem;
>> +/delete-node/ &wlan_msa_mem;
>> +
>> +/ {
>> +       model = "Xiaomi Mi 6";
>> +       compatible = "xiaomi,sagit", "qcom,msm8998";
>> +       chassis-type = "handset";
>> +       /* Required for bootloader to select correct board */
>> +       qcom,board-id = <30 0>;
>> +
>> +       reserved-memory {
>> +               /*
>> +                * The following memory regions on downstream are "dynamically allocated"
>> +                * but given the same addresses every time. Hard code them as these addresses
>> +                * are where the Xiaomi signed firmware expects them to be.
>> +                */
>> +               ipa_fws_region: ipa@f7800000 {
memory@
>> +                       compatible = "shared-dma-pool";
>> +                       reg = <0x0 0xf7800000 0x0 0x5000>;
>> +                       no-map;
>> +               };
>> +
>> +               zap_shader_region: gpu@f7900000 {
memory@
>> +                       compatible = "shared-dma-pool";
>> +                       reg = <0x0 0xf7900000 0x0 0x2000>;
>> +                       no-map;
>> +               };
>> +
>> +               mpss_mem: memory@8d000000 {
>> +                       reg = <0x0 0x8d000000 0x0 0x7000000>;
>> +                       no-map;
>> +               };
>> +
>> +               venus_mem: memory@94000000 {
>> +                       reg = <0x0 0x94000000 0x0 0x500000>;
>> +                       no-map;
>> +               };
>> +
>> +               mba_mem: memory@94500000 {
>> +                       reg = <0x0 0x94500000 0x0 0x200000>;
>> +                       no-map;
>> +               };
>> +
>> +               slpi_mem: memory@94700000 {
>> +                       reg = <0x0 0x94700000 0x0 0x10000>;
>> +                       no-map;
>> +               };
>> +
>> +               ipa_fw_mem: memory@95600000 {
>> +                       reg = <0x0 0x95600000 0x0 0x10000>;
>> +                       no-map;
>> +               };
>> +
>> +               ipa_gsi_mem: memory@95610000 {
>> +                       reg = <0x0 0x95610000 0x0 0x5000>;
>> +                       no-map;
>> +               };
>> +
>> +               gpu_mem: memory@95615000 {
>> +                       reg = <0x0 0x95615000 0x0 0x100000>;
>> +                       no-map;
>> +               };
>> +
>> +               wlan_msa_mem: memory@95715000 {
>> +                       reg = <0x0 0x95715000 0x0 0x100000>;
>> +                       no-map;
>> +               };
>> +       };
>> +
>> +       gpio-keys {
>> +               compatible = "gpio-keys";
>> +               label = "Volume buttons";
>> +               autorepeat;
>> +
>> +               pinctrl-names = "default";
>> +               pinctrl-0 = <&vol_up_key_default>;
>> +
>> +               key-vol-up {
>> +                       label = "Volume up";
>> +                       gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
>> +                       linux,code = <KEY_VOLUMEUP>;
>> +                       debounce-interval = <15>;
>> +                       wakeup-source;
>> +               };
>> +       };
>> +
>> +       gpio-hall-sensor {
>> +               compatible = "gpio-keys";
>> +               label = "Hall effect sensor";
>> +
>> +               pinctrl-names = "default";
>> +               pinctrl-0 = <&hall_sensor_default_state>;
>> +
>> +               event-hall-sensor {
>> +                       label = "Hall Effect Sensor";
>> +                       gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
>> +                       linux,input-type = <EV_SW>;
>> +                       linux,code = <SW_LID>;
>> +                       linux,can-disable;
>> +                       wakeup-source;
>> +               };
>> +       };
>> +
>> +       vph_pwr: vph-pwr-regulator {
>> +               compatible = "regulator-fixed";
>> +               regulator-name = "vph_pwr";
>> +               regulator-min-microvolt = <3700000>;
>> +               regulator-max-microvolt = <3700000>;
>> +               regulator-always-on;
>> +               regulator-boot-on;
>> +       };
>> +
>> +       disp_vddts_vreg: disp-vddts-regulator {
>> +               compatible = "regulator-fixed";
>> +               regulator-name = "disp-vddts-regulator";
>> +               gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
>> +               enable-active-high;
>> +               regulator-boot-on;
>> +       };
>> +};
>> +
>> +&blsp1_i2c5 {
>> +       pinctrl-names = "default", "sleep";
>> +
>> +       touchscreen@20 {
>> +               compatible = "syna,rmi4-i2c";
>> +               reg = <0x20>;
>> +               #address-cells = <1>;
>> +               #size-cells = <0>;
>> +
>> +               interrupt-parent = <&tlmm>;
>> +               interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
>> +
>> +               pinctrl-names = "default", "sleep";
>> +               pinctrl-0 = <&ts_active_state>;
>> +               pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
>> +
>> +               vdd-supply = <&disp_vddts_vreg>;
>> +               vio-supply = <&vreg_l6a_1p8>;
>> +
>> +               syna,reset-delay-ms = <20>;
>> +               syna,startup-delay-ms = <20>;
>> +
>> +               rmi4-f01@1 {
>> +                       reg = <0x01>;
>> +                       syna,nosleep-mode = <1>;
>> +               };
>> +
>> +               rmi4-f12@12 {
>> +                       reg = <0x12>;
>> +                       touchscreen-x-mm = <64>;
>> +                       touchscreen-y-mm = <114>;
>> +                       syna,sensor-type = <1>;
>> +                       syna,rezero-wait-ms = <20>;
>> +               };
>> +
>> +               rmi4-f1a@1a {
>> +                       reg = <0x1a>;
>> +                       syna,codes = <KEY_BACK KEY_APPSELECT>;
>> +               };
>> +       };
>> +       status = "okay";
This generates a DTC warning. Status should be the last *property*. However,
properties must precede subnodes. This applies to all occurences.

>> +};
>> +
>> +&blsp1_i2c5_sleep {
>> +       /delete-property/ bias-pull-up;
>> +       bias-disable;
>> +};
>> +
>> +&blsp1_uart3 {
>> +       bluetooth {
>> +               compatible = "qcom,wcn3990-bt";
>> +
>> +               vddio-supply = <&vreg_s4a_1p8>;
>> +               vddxo-supply = <&vreg_l7a_1p8>;
>> +               vddrf-supply = <&vreg_l17a_1p3>;
>> +               vddch0-supply = <&vreg_l25a_3p3>;
>> +               max-speed = <3200000>;
>> +       };
>> +       status = "okay";
>> +};
>> +
>> +&blsp1_uart3_on {
>> +       rx {
>> +               /delete-property/ bias-disable;
>> +               /*
>> +                * Configure a pull-up on 46 (RX). This is needed to
>> +                * avoid garbage data when the TX pin of the Bluetooth
>> +                * module is in tri-state (module powered off or not
>> +                * driving the signal yet).
>> +                */
>> +               bias-pull-up;
>> +       };
>> +
>> +       cts {
>> +               /delete-property/ bias-disable;
>> +               /*
>> +                * Configure a pull-down on 47 (CTS) to match the pull
>> +                * of the Bluetooth module.
>> +                */
>> +               bias-pull-down;
>> +       };
>> +};
>> +
>> +&blsp2_uart1 {
>> +       status = "okay";
>> +};
>> +
>> +&pm8005_regulators {
>> +       compatible = "qcom,pm8005-regulators";
>> +
>> +       vdd_s1-supply = <&vph_pwr>;
>> +
>> +       pm8005_s1: s1 { /* VDD_GFX supply */
>> +               regulator-min-microvolt = <524000>;
>> +               regulator-max-microvolt = <1100000>;
>> +               regulator-enable-ramp-delay = <500>;
>> +
>> +               /* hack until we rig up the gpu consumer */
>> +               regulator-always-on;
>> +       };
>> +};
>> +
>> +&pm8998_gpio {
>> +       vol_up_key_default: vol-up-key-default-state {
>> +               pins = "gpio6";
>> +               function = "normal";
>> +               bias-pull-up;
>> +               input-enable;
>> +               qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
>> +       };
>> +
>> +       audio_mclk_pin: audio-mclk-pin-active-state {
>> +               pins = "gpio13";
>> +               function = "func2";
>> +               power-source = <0>;
>> +       };
>> +};
>> +
>> +&qusb2phy {
>> +       vdda-pll-supply = <&vreg_l12a_1p8>;
>> +       vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
>> +       status = "okay";
>> +};
>> +
>> +&rpm_requests {
>> +       regulators-0 {
>> +               compatible = "qcom,rpm-pm8998-regulators";
>> +
>> +               vdd_s1-supply = <&vph_pwr>;
>> +               vdd_s2-supply = <&vph_pwr>;
>> +               vdd_s3-supply = <&vph_pwr>;
>> +               vdd_s4-supply = <&vph_pwr>;
>> +               vdd_s5-supply = <&vph_pwr>;
>> +               vdd_s6-supply = <&vph_pwr>;
>> +               vdd_s7-supply = <&vph_pwr>;
>> +               vdd_s8-supply = <&vph_pwr>;
>> +               vdd_s9-supply = <&vph_pwr>;
>> +               vdd_s10-supply = <&vph_pwr>;
>> +               vdd_s11-supply = <&vph_pwr>;
>> +               vdd_s12-supply = <&vph_pwr>;
>> +               vdd_s13-supply = <&vph_pwr>;
>> +               vdd_l1_l27-supply = <&vreg_s7a_1p025>;
>> +               vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
>> +               vdd_l3_l11-supply = <&vreg_s7a_1p025>;
>> +               vdd_l4_l5-supply = <&vreg_s7a_1p025>;
>> +               vdd_l6-supply = <&vreg_s5a_2p04>;
>> +               vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
>> +               vdd_l9-supply = <&vreg_bob>;
>> +               vdd_l10_l23_l25-supply = <&vreg_bob>;
>> +               vdd_l13_l19_l21-supply = <&vreg_bob>;
>> +               vdd_l16_l28-supply = <&vreg_bob>;
>> +               vdd_l18_l22-supply = <&vreg_bob>;
>> +               vdd_l20_l24-supply = <&vreg_bob>;
>> +               vdd_l26-supply = <&vreg_s3a_1p35>;
>> +               vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
>> +
>> +               vreg_s3a_1p35: s3 {
>> +                       regulator-min-microvolt = <1352000>;
>> +                       regulator-max-microvolt = <1352000>;
>> +               };
>> +
>> +               vreg_s4a_1p8: s4 {
>> +                       regulator-min-microvolt = <1800000>;
>> +                       regulator-max-microvolt = <1800000>;
>> +                       regulator-allow-set-load;
>> +               };
>> +
>> +               vreg_s5a_2p04: s5 {
>> +                       regulator-min-microvolt = <1904000>;
>> +                       regulator-max-microvolt = <2040000>;
>> +               };
>> +
>> +               vreg_s7a_1p025: s7 {
>> +                       regulator-min-microvolt = <900000>;
>> +                       regulator-max-microvolt = <1028000>;
>> +               };
>> +
>> +               vreg_l1a_0p875: l1 {
>> +                       regulator-min-microvolt = <880000>;
>> +                       regulator-max-microvolt = <880000>;
>> +               };
>> +
>> +               vreg_l2a_1p2: l2 {
>> +                       regulator-min-microvolt = <1200000>;
>> +                       regulator-max-microvolt = <1200000>;
>> +               };
>> +
>> +               vreg_l3a_1p0: l3 {
>> +                       regulator-min-microvolt = <1000000>;
>> +                       regulator-max-microvolt = <1000000>;
>> +               };
>> +
>> +               vreg_l5a_0p8: l5 {
>> +                       regulator-min-microvolt = <800000>;
>> +                       regulator-max-microvolt = <800000>;
>> +               };
>> +
>> +               vreg_l6a_1p8: l6 {
>> +                       regulator-min-microvolt = <1800000>;
>> +                       regulator-max-microvolt = <1800000>;
>> +               };
>> +
>> +               vreg_l7a_1p8: l7 {
>> +                       regulator-min-microvolt = <1800000>;
>> +                       regulator-max-microvolt = <1800000>;
>> +               };
>> +
>> +               vreg_l8a_1p2: l8 {
>> +                       regulator-min-microvolt = <1200000>;
>> +                       regulator-max-microvolt = <1200000>;
>> +               };
>> +
>> +               vreg_l9a_1p8: l9 {
>> +                       regulator-min-microvolt = <1808000>;
>> +                       regulator-max-microvolt = <2960000>;
>> +               };
>> +
>> +               vreg_l10a_1p8: l10 {
>> +                       regulator-min-microvolt = <1808000>;
>> +                       regulator-max-microvolt = <2960000>;
>> +               };
>> +
>> +               vreg_l11a_1p0: l11 {
>> +                       regulator-min-microvolt = <1000000>;
>> +                       regulator-max-microvolt = <1000000>;
>> +               };
>> +
>> +               vreg_l12a_1p8: l12 {
>> +                       regulator-min-microvolt = <1800000>;
>> +                       regulator-max-microvolt = <1800000>;
>> +               };
>> +
>> +               vreg_l13a_2p95: l13 {
>> +                       regulator-min-microvolt = <1808000>;
>> +                       regulator-max-microvolt = <2960000>;
>> +               };
>> +
>> +               vreg_l14a_1p8: l14 {
>> +                       regulator-min-microvolt = <1800000>;
>> +                       regulator-max-microvolt = <1800000>;
>> +               };
>> +
>> +               vreg_l15a_1p8: l15 {
>> +                       regulator-min-microvolt = <1800000>;
>> +                       regulator-max-microvolt = <1800000>;
>> +               };
>> +
>> +               vreg_l16a_2p7: l16 {
>> +                       regulator-min-microvolt = <2704000>;
>> +                       regulator-max-microvolt = <2704000>;
>> +               };
>> +
>> +               vreg_l17a_1p3: l17 {
>> +                       regulator-min-microvolt = <1304000>;
>> +                       regulator-max-microvolt = <1304000>;
>> +               };
>> +
>> +               vreg_l18a_2p7: l18 {
>> +                       regulator-min-microvolt = <2704000>;
>> +                       regulator-max-microvolt = <2704000>;
>> +               };
>> +
>> +               vreg_l19a_3p0: l19 {
>> +                       regulator-min-microvolt = <3008000>;
>> +                       regulator-max-microvolt = <3008000>;
>> +               };
>> +
>> +               vreg_l20a_2p95: l20 {
>> +                       regulator-min-microvolt = <2960000>;
>> +                       regulator-max-microvolt = <2960000>;
>> +                       regulator-allow-set-load;
>> +               };
>> +
>> +               vreg_l21a_2p95: l21 {
>> +                       regulator-min-microvolt = <2960000>;
>> +                       regulator-max-microvolt = <2960000>;
>> +                       regulator-system-load = <800000>;
>> +                       regulator-allow-set-load;
>> +               };
>> +
>> +               vreg_l22a_2p85: l22 {
>> +                       regulator-min-microvolt = <2864000>;
>> +                       regulator-max-microvolt = <2864000>;
>> +               };
>> +
>> +               vreg_l23a_3p3: l23 {
>> +                       regulator-min-microvolt = <3312000>;
>> +                       regulator-max-microvolt = <3312000>;
>> +               };
>> +
>> +               vreg_l24a_3p075: l24 {
>> +                       regulator-min-microvolt = <3088000>;
>> +                       regulator-max-microvolt = <3088000>;
>> +               };
>> +
>> +               vreg_l25a_3p3: l25 {
>> +                       regulator-min-microvolt = <3104000>;
>> +                       regulator-max-microvolt = <3312000>;
>> +               };
>> +
>> +               vreg_l26a_1p2: l26 {
>> +                       regulator-min-microvolt = <1200000>;
>> +                       regulator-max-microvolt = <1200000>;
>> +                       regulator-allow-set-load;
>> +               };
>> +
>> +               vreg_l28_3p0: l28 {
>> +                       regulator-min-microvolt = <3008000>;
>> +                       regulator-max-microvolt = <3008000>;
>> +               };
>> +
>> +               vreg_lvs1a_1p8: lvs1 { };
>> +
>> +               vreg_lvs2a_1p8: lvs2 { };
>> +       };
>> +
>> +       regulators-1 {
>> +               compatible = "qcom,rpm-pmi8998-regulators";
>> +
>> +               vdd_bob-supply = <&vph_pwr>;
>> +
>> +               vreg_bob: bob {
>> +                       regulator-min-microvolt = <3312000>;
>> +                       regulator-max-microvolt = <3600000>;
>> +               };
>> +       };
>> +};
>> +
>> +&tlmm {
>> +       gpio-reserved-ranges = <0 4>, <81 4>;
>> +
>> +       cci1_default_state: cci1-default-state {
>> +               pins = "gpio19", "gpio20";
>> +               function = "cci_i2c";
>> +               bias-disable;
>> +               drive-strength = <2>;
>> +       };
>> +
>> +       cdc_reset_n_state: cdc-reset-n-state {
>> +               pins = "gpio64";
>> +               function = "gpio";
>> +               bias-pull-down;
>> +               drive-strength = <16>;
>> +               output-high;
>> +       };
>> +
>> +       hall_sensor_default_state: hall-sensor-default-state {
>> +               pins = "gpio124";
>> +               function = "gpio";
>> +               drive-strength = <2>;
>> +               bias-disable;
>> +               input-enable;
>> +       };
>> +
>> +       mdss_dsi_active_state: mdss-dsi-active-state {
>> +               pins = "gpio94";
>> +               function = "gpio";
>> +               drive-strength = <8>;
>> +               bias-disable;
>> +       };
>> +
>> +       mdss_dsi_suspend_state: mdss-dsi-suspend-state {
>> +               pins = "gpio94";
>> +               function = "gpio";
>> +               drive-strength = <2>;
>> +               bias-pull-down;
>> +       };
>> +
>> +       mdss_te_active_state: mdss-te-active-state {
>> +               pins = "gpio10";
>> +               function = "mdp_vsync_a";
>> +               drive-strength = <2>;
>> +               bias-pull-down;
>> +       };
>> +
>> +       mdss_te_suspend_state: mdss-te-suspend-state {
>> +               pins = "gpio10";
>> +               function = "mdp_vsync_a";
>> +               drive-strength = <2>;
>> +               bias-pull-down;
>> +       };
>> +
>> +       msm_mclk0_active_state: msm-mclk0-active-state {
>> +               pins = "gpio13";
>> +               function = "cam_mclk";
>> +               drive-strength = <2>;
>> +               bias-disable;
>> +       };
>> +
>> +       msm_mclk0_suspend_state: msm-mclk0-suspend-state {
>> +               pins = "gpio13";
>> +               function = "cam_mclk";
>> +               drive-strength = <2>;
>> +               bias-pull-down;
>> +       };
>> +
>> +       msm_mclk1_active_state: msm-mclk1-active-state {
>> +               pins = "gpio14";
>> +               function = "cam_mclk";
>> +               drive-strength = <2>;
>> +               bias-disable;
>> +       };
>> +
>> +       msm_mclk1_suspend_state: msm-mclk1-suspend-state {
>> +               pins = "gpio14";
>> +               function = "cam_mclk";
>> +               drive-strength = <2>;
>> +               bias-pull-down;
>> +       };
>> +
>> +       nfc_int_active_state: nfc-int-active-state {
>> +               pins = "gpio92";
>> +               function = "gpio";
>> +               drive-strength = <6>;
>> +               bias-pull-up;
>> +       };
>> +
>> +       nfc_int_suspend_state: nfc-int-suspend-state {
>> +               pins = "gpio92";
>> +               function = "gpio";
>> +               drive-strength = <6>;
>> +               bias-pull-up;
>> +       };
>> +
>> +       nfc_enable_active_state: nfc-enable-active-state {
>> +               pins = "gpio12", "gpio116";
>> +               function = "gpio";
>> +               drive-strength = <6>;
>> +               bias-pull-up;
>> +       };
>> +
>> +       nfc_enable_suspend_state: nfc-enable-suspend-state {
>> +               pins = "gpio12", "gpio116";
>> +               function = "gpio";
>> +               drive-strength = <6>;
>> +               bias-disable;
>> +       };
>> +
>> +       ts_active_state: ts-active-state {
>> +               pins = "gpio89", "gpio125";
>> +               function = "gpio";
>> +               drive-strength = <16>;
>> +               bias-pull-up;
>> +               input-enable;
>> +       };
>> +
>> +       ts_int_suspend_state: ts-int-suspend-state {
>> +               pins = "gpio125";
>> +               function = "gpio";
>> +               drive-strength = <2>;
>> +               bias-disable;
>> +       };
>> +
>> +       ts_reset_suspend_state: ts-reset-suspend-state {
>> +               pins = "gpio89";
>> +               function = "gpio";
>> +               drive-strength = <2>;
>> +               bias-disable;
>> +       };
>> +
>> +       wcd_int_n_state: wcd-int-n-state {
>> +               pins = "gpio54";
>> +               function = "gpio";
>> +               bias-pull-down;
>> +               drive-strength = <2>;
>> +               input-enable;
>> +       };
>> +
>> +       wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state {
>> +               pins = "gpio65";
>> +               function = "gpio";
>> +               bias-disable;
>> +               drive-strength = <2>;
>> +               output-low;
>> +       };
>> +
>> +       wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state {
>> +               pins = "gpio66";
>> +               function = "gpio";
>> +               bias-disable;
>> +               drive-strength = <2>;
>> +               output-low;
>> +       };
>> +};
>> +
>> +&pm8998_resin {
>> +       linux,code = <KEY_VOLUMEDOWN>;
>> +};
You forgot to enable it.

Konrad
>> +
>> +&ufshc {
>> +       vcc-supply = <&vreg_l20a_2p95>;
>> +       vccq-supply = <&vreg_l26a_1p2>;
>> +       vccq2-supply = <&vreg_s4a_1p8>;
>> +       vcc-max-microamp = <750000>;
>> +       vccq-max-microamp = <560000>;
>> +       vccq2-max-microamp = <750000>;
>> +       status = "okay";
>> +};
>> +
>> +&ufsphy {
>> +       vdda-phy-supply = <&vreg_l1a_0p875>;
>> +       vdda-pll-supply = <&vreg_l2a_1p2>;
>> +       vddp-ref-clk-supply = <&vreg_l26a_1p2>;
>> +       status = "okay";
>> +};
>> +
>> +&usb3 {
>> +       /* Disable USB3 clock requirement as the device only supports USB2 */
>> +       qcom,select-utmi-as-pipe-clk;
>> +       status = "okay";
>> +};
>> +
>> +&usb3_dwc3 {
>> +       /* Drop the unused USB 3 PHY */
>> +       phys = <&qusb2phy>;
>> +       phy-names = "usb2-phy";
>> +
>> +       /* Fastest mode for USB 2 */
>> +       maximum-speed = "high-speed";
>> +
>> +       /* Force to peripheral until we can switch modes */
>> +       dr_mode = "peripheral";
>> +};
>> +
>> +&wifi {
>> +       vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
>> +       vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
>> +       vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
>> +       vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
>> +       status = "okay";
>> +};
>> diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
>> index d09f2954b6f9..7929fa64e1ef 100644
>> --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
>> @@ -52,6 +52,14 @@ pm8998_pwrkey: pwrkey {
>>                                 bias-pull-up;
>>                                 linux,code = <KEY_POWER>;
>>                         };
>> +
>> +                       pm8998_resin: resin {
>> +                               compatible = "qcom,pm8941-resin";
>> +                               bias-pull-up;
>> +                               interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
>> +                               debounce = <15625>;
>> +                               status = "disabled";
>> +                       };
>>                 };
>>
>>                 pm8998_temp: temp-alarm@2400 {
>> --
>> 2.30.2
>>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1d86a33de528..0460aabf1b59 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -46,6 +46,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-oneplus-dumpling.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-lilac.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-maple.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-poplar.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-xiaomi-sagit.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
new file mode 100644
index 000000000000..e44f6a745a2c
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
@@ -0,0 +1,681 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
+ *
+ * Copyright (c) 2022, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
+ * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/*
+ * Delete following upstream (msm8998.dtsi) reserved
+ * memory mappings which are different in this device.
+ */
+/delete-node/ &mpss_mem;
+/delete-node/ &venus_mem;
+/delete-node/ &mba_mem;
+/delete-node/ &slpi_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &gpu_mem;
+/delete-node/ &wlan_msa_mem;
+
+/ {
+	model = "Xiaomi Mi 6";
+	compatible = "xiaomi,sagit", "qcom,msm8998";
+	chassis-type = "handset";
+	/* Required for bootloader to select correct board */
+	qcom,board-id = <30 0>;
+
+	reserved-memory {
+		/*
+		 * The following memory regions on downstream are "dynamically allocated"
+		 * but given the same addresses every time. Hard code them as these addresses
+		 * are where the Xiaomi signed firmware expects them to be.
+		 */
+		ipa_fws_region: ipa@f7800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf7800000 0x0 0x5000>;
+			no-map;
+		};
+
+		zap_shader_region: gpu@f7900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf7900000 0x0 0x2000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8d000000 {
+			reg = <0x0 0x8d000000 0x0 0x7000000>;
+			no-map;
+		};
+
+		venus_mem: memory@94000000 {
+			reg = <0x0 0x94000000 0x0 0x500000>;
+			no-map;
+		};
+
+		mba_mem: memory@94500000 {
+			reg = <0x0 0x94500000 0x0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: memory@94700000 {
+			reg = <0x0 0x94700000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@95600000 {
+			reg = <0x0 0x95600000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: memory@95610000 {
+			reg = <0x0 0x95610000 0x0 0x5000>;
+			no-map;
+		};
+
+		gpu_mem: memory@95615000 {
+			reg = <0x0 0x95615000 0x0 0x100000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@95715000 {
+			reg = <0x0 0x95715000 0x0 0x100000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		label = "Volume buttons";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_key_default>;
+
+		key-vol-up {
+			label = "Volume up";
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+			wakeup-source;
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+		label = "Hall effect sensor";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hall_sensor_default_state>;
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	disp_vddts_vreg: disp-vddts-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "disp-vddts-regulator";
+		gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&blsp1_i2c5 {
+	pinctrl-names = "default", "sleep";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ts_active_state>;
+		pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
+
+		vdd-supply = <&disp_vddts_vreg>;
+		vio-supply = <&vreg_l6a_1p8>;
+
+		syna,reset-delay-ms = <20>;
+		syna,startup-delay-ms = <20>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			touchscreen-x-mm = <64>;
+			touchscreen-y-mm = <114>;
+			syna,sensor-type = <1>;
+			syna,rezero-wait-ms = <20>;
+		};
+
+		rmi4-f1a@1a {
+			reg = <0x1a>;
+			syna,codes = <KEY_BACK KEY_APPSELECT>;
+		};
+	};
+	status = "okay";
+};
+
+&blsp1_i2c5_sleep {
+	/delete-property/ bias-pull-up;
+	bias-disable;
+};
+
+&blsp1_uart3 {
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+	status = "okay";
+};
+
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 46 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+};
+
+&pm8005_regulators {
+	compatible = "qcom,pm8005-regulators";
+
+	vdd_s1-supply = <&vph_pwr>;
+
+	pm8005_s1: s1 { /* VDD_GFX supply */
+		regulator-min-microvolt = <524000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-enable-ramp-delay = <500>;
+
+		/* hack until we rig up the gpu consumer */
+		regulator-always-on;
+	};
+};
+
+&pm8998_gpio {
+	vol_up_key_default: vol-up-key-default-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	audio_mclk_pin: audio-mclk-pin-active-state {
+		pins = "gpio13";
+		function = "func2";
+		power-source = <0>;
+	};
+};
+
+&qusb2phy {
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8998-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_s13-supply = <&vph_pwr>;
+		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+		vdd_l6-supply = <&vreg_s5a_2p04>;
+		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+		vdd_l9-supply = <&vreg_bob>;
+		vdd_l10_l23_l25-supply = <&vreg_bob>;
+		vdd_l13_l19_l21-supply = <&vreg_bob>;
+		vdd_l16_l28-supply = <&vreg_bob>;
+		vdd_l18_l22-supply = <&vreg_bob>;
+		vdd_l20_l24-supply = <&vreg_bob>;
+		vdd_l26-supply = <&vreg_s3a_1p35>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: s3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s4a_1p8: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_s5a_2p04: s5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: s7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p875: l1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l2a_1p2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l3a_1p0: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l5a_0p8: l5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l6a_1p8: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l7a_1p8: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l8a_1p2: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l10a_1p8: l10 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l11a_1p0: l11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l12a_1p8: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l13a_2p95: l13 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l14a_1p8: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l15a_1p8: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l16a_2p7: l16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l17a_1p3: l17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a_2p7: l18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l19a_3p0: l19 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_l20a_2p95: l20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l21a_2p95: l21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-system-load = <800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l22a_2p85: l22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <2864000>;
+		};
+
+		vreg_l23a_3p3: l23 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l24a_3p075: l24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+		};
+
+		vreg_l25a_3p3: l25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l26a_1p2: l26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l28_3p0: l28 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 { };
+
+		vreg_lvs2a_1p8: lvs2 { };
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pmi8998-regulators";
+
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	cci1_default_state: cci1-default-state {
+		pins = "gpio19", "gpio20";
+		function = "cci_i2c";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	cdc_reset_n_state: cdc-reset-n-state {
+		pins = "gpio64";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <16>;
+		output-high;
+	};
+
+	hall_sensor_default_state: hall-sensor-default-state {
+		pins = "gpio124";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	mdss_dsi_active_state: mdss-dsi-active-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	mdss_dsi_suspend_state: mdss-dsi-suspend-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_active_state: mdss-te-active-state {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_suspend_state: mdss-te-suspend-state {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	msm_mclk0_active_state: msm-mclk0-active-state {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk0_suspend_state: msm-mclk0-suspend-state {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	msm_mclk1_active_state: msm-mclk1-active-state {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk1_suspend_state: msm-mclk1-suspend-state {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	nfc_int_active_state: nfc-int-active-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_int_suspend_state: nfc-int-suspend-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_active_state: nfc-enable-active-state {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_suspend_state: nfc-enable-suspend-state {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	ts_active_state: ts-active-state {
+		pins = "gpio89", "gpio125";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	ts_int_suspend_state: ts-int-suspend-state {
+		pins = "gpio125";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	ts_reset_suspend_state: ts-reset-suspend-state {
+		pins = "gpio89";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcd_int_n_state: wcd-int-n-state {
+		pins = "gpio54";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+		input-enable;
+	};
+
+	wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state {
+		pins = "gpio65";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+
+	wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state {
+		pins = "gpio66";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+};
+
+&pm8998_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&ufshc {
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l26a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vcc-max-microamp = <750000>;
+	vccq-max-microamp = <560000>;
+	vccq2-max-microamp = <750000>;
+	status = "okay";
+};
+
+&ufsphy {
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+	status = "okay";
+};
+
+&usb3 {
+	/* Disable USB3 clock requirement as the device only supports USB2 */
+	qcom,select-utmi-as-pipe-clk;
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	/* Drop the unused USB 3 PHY */
+	phys = <&qusb2phy>;
+	phy-names = "usb2-phy";
+
+	/* Fastest mode for USB 2 */
+	maximum-speed = "high-speed";
+
+	/* Force to peripheral until we can switch modes */
+	dr_mode = "peripheral";
+};
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
index d09f2954b6f9..7929fa64e1ef 100644
--- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
@@ -52,6 +52,14 @@  pm8998_pwrkey: pwrkey {
 				bias-pull-up;
 				linux,code = <KEY_POWER>;
 			};
+
+			pm8998_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				bias-pull-up;
+				interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				status = "disabled";
+			};
 		};
 
 		pm8998_temp: temp-alarm@2400 {