@@ -69,11 +69,6 @@
struct qmp_phy_init_tbl {
unsigned int offset;
unsigned int val;
- /*
- * register part of layout ?
- * if yes, then offset gives index in the reg-layout
- */
- bool in_layout;
/*
* mask of lanes for which this register is written
* for cases when second lane needs different values
@@ -88,14 +83,6 @@ struct qmp_phy_init_tbl {
.lane_mask = 0xff, \
}
-#define QMP_PHY_INIT_CFG_L(o, v) \
- { \
- .offset = o, \
- .val = v, \
- .in_layout = true, \
- .lane_mask = 0xff, \
- }
-
#define QMP_PHY_INIT_CFG_LANE(o, v, l) \
{ \
.offset = o, \
@@ -1346,7 +1333,6 @@ static const struct qmp_phy_combo_cfg sm8250_usb3dpphy_cfg = {
};
static void qmp_combo_configure_lane(void __iomem *base,
- const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
int num,
u8 lane_mask)
@@ -1361,19 +1347,15 @@ static void qmp_combo_configure_lane(void __iomem *base,
if (!(t->lane_mask & lane_mask))
continue;
- if (t->in_layout)
- writel(t->val, base + regs[t->offset]);
- else
- writel(t->val, base + t->offset);
+ writel(t->val, base + t->offset);
}
}
static void qmp_combo_configure(void __iomem *base,
- const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
int num)
{
- qmp_combo_configure_lane(base, regs, tbl, num, 0xff);
+ qmp_combo_configure_lane(base, tbl, num, 0xff);
}
static int qmp_combo_serdes_init(struct qmp_phy *qphy)
@@ -1384,28 +1366,24 @@ static int qmp_combo_serdes_init(struct qmp_phy *qphy)
const struct qmp_phy_init_tbl *serdes_tbl = cfg->serdes_tbl;
int serdes_tbl_num = cfg->serdes_tbl_num;
- qmp_combo_configure(serdes, cfg->regs, serdes_tbl, serdes_tbl_num);
+ qmp_combo_configure(serdes, serdes_tbl, serdes_tbl_num);
if (cfg->type == PHY_TYPE_DP) {
switch (dp_opts->link_rate) {
case 1620:
- qmp_combo_configure(serdes, cfg->regs,
- cfg->serdes_tbl_rbr,
+ qmp_combo_configure(serdes, cfg->serdes_tbl_rbr,
cfg->serdes_tbl_rbr_num);
break;
case 2700:
- qmp_combo_configure(serdes, cfg->regs,
- cfg->serdes_tbl_hbr,
+ qmp_combo_configure(serdes, cfg->serdes_tbl_hbr,
cfg->serdes_tbl_hbr_num);
break;
case 5400:
- qmp_combo_configure(serdes, cfg->regs,
- cfg->serdes_tbl_hbr2,
+ qmp_combo_configure(serdes, cfg->serdes_tbl_hbr2,
cfg->serdes_tbl_hbr2_num);
break;
case 8100:
- qmp_combo_configure(serdes, cfg->regs,
- cfg->serdes_tbl_hbr3,
+ qmp_combo_configure(serdes, cfg->serdes_tbl_hbr3,
cfg->serdes_tbl_hbr3_num);
break;
default:
@@ -2069,29 +2047,25 @@ static int qmp_combo_power_on(struct phy *phy)
}
/* Tx, Rx, and PCS configurations */
- qmp_combo_configure_lane(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num, 1);
+ qmp_combo_configure_lane(tx, cfg->tx_tbl, cfg->tx_tbl_num, 1);
- if (cfg->lanes >= 2) {
- qmp_combo_configure_lane(qphy->tx2, cfg->regs, cfg->tx_tbl,
- cfg->tx_tbl_num, 2);
- }
+ if (cfg->lanes >= 2)
+ qmp_combo_configure_lane(qphy->tx2, cfg->tx_tbl, cfg->tx_tbl_num, 2);
/* Configure special DP tx tunings */
if (cfg->type == PHY_TYPE_DP)
cfg->configure_dp_tx(qphy);
- qmp_combo_configure_lane(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num, 1);
+ qmp_combo_configure_lane(rx, cfg->rx_tbl, cfg->rx_tbl_num, 1);
- if (cfg->lanes >= 2) {
- qmp_combo_configure_lane(qphy->rx2, cfg->regs, cfg->rx_tbl,
- cfg->rx_tbl_num, 2);
- }
+ if (cfg->lanes >= 2)
+ qmp_combo_configure_lane(qphy->rx2, cfg->rx_tbl, cfg->rx_tbl_num, 2);
/* Configure link rate, swing, etc. */
if (cfg->type == PHY_TYPE_DP)
cfg->configure_dp_phy(qphy);
else
- qmp_combo_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+ qmp_combo_configure(pcs, cfg->pcs_tbl, cfg->pcs_tbl_num);
if (cfg->has_pwrdn_delay)
usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max);
The QMP combo PHY driver does not use the "in-layout" configuration macro to configure registers that are typically accessed using "regs_layout" arrays (e.g. QPHY_START_CTRL) so drop this unused feature. Signed-off-by: Johan Hovold <johan+linaro@kernel.org> --- drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 54 ++++++----------------- 1 file changed, 14 insertions(+), 40 deletions(-)