diff mbox series

[v1,9/9] arm64: dts: qcom: sm8350-hdk: Enable lt9611uxc dsi-hdmi bridge

Message ID 20221028120812.339100-10-robert.foss@linaro.org (mailing list archive)
State Superseded
Headers show
Series Enable Display for SM8350 | expand

Commit Message

Robert Foss Oct. 28, 2022, 12:08 p.m. UTC
The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.

In order to toggle the board to enable the HDMI output,
switch #7 & #8 on the rightmost multi-switch package have
to be toggled to On.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 106 ++++++++++++++++++++++++
 1 file changed, 106 insertions(+)

Comments

Dmitry Baryshkov Oct. 28, 2022, 1:56 p.m. UTC | #1
On 28/10/2022 15:08, Robert Foss wrote:
> The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.
> 
> In order to toggle the board to enable the HDMI output,
> switch #7 & #8 on the rightmost multi-switch package have
> to be toggled to On.

Since this doesn't look like a default setup, it would probably make 
sense to move this to new sm8350-hdk-hdmi.dts with the comment regarding 
necessary switch changes at the top of the file.

> 
> Signed-off-by: Robert Foss <robert.foss@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 106 ++++++++++++++++++++++++
>   1 file changed, 106 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 6e07feb4b3b2..6666b38b58f8 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -20,6 +20,17 @@ chosen {
>   		stdout-path = "serial0:115200n8";
>   	};
>   
> +	hdmi-out {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&lt9611_out>;
> +			};
> +		};
> +	};
> +
>   	vph_pwr: vph-pwr-regulator {
>   		compatible = "regulator-fixed";
>   		regulator-name = "vph_pwr";
> @@ -29,6 +40,32 @@ vph_pwr: vph-pwr-regulator {
>   		regulator-always-on;
>   		regulator-boot-on;
>   	};
> +
> +	lt9611_1v2: lt9611-1v2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_1V2";
> +
> +		vin-supply = <&vph_pwr>;
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	lt9611_3v3: lt9611-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_3V3";
> +
> +		vin-supply = <&vreg_bob>;
> +		gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
>   };
>   
>   &adsp {
> @@ -220,6 +257,15 @@ &dispcc {
>   &dsi0 {
>   	status = "okay";
>   	vdda-supply = <&vreg_l6b_1p2>;
> +
> +	ports {
> +		port@1 {
> +			endpoint {
> +				remote-endpoint = <&lt9611_a>;
> +				data-lanes = <0 1 2 3>;
> +			};
> +		};
> +	};
>   };
>   
>   &dsi0_phy  {
> @@ -231,6 +277,48 @@ &gpi_dma1 {
>   	status = "okay";
>   };
>   
> +&i2c15 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	lt9611_codec: hdmi-bridge@2b {
> +		compatible = "lontium,lt9611uxc";
> +		reg = <0x2b>;
> +		status = "okay";
> +
> +		interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
> +		reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
> +
> +		vdd-supply = <&lt9611_1v2>;
> +		vcc-supply = <&lt9611_3v3>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				lt9611_a: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +
> +				lt9611_out: endpoint {
> +					remote-endpoint = <&hdmi_con>;
> +				};
> +			};
> +
> +		};
> +	};
> +};
> +
>   &mdss {
>   	status = "okay";
>   };
> @@ -248,6 +336,10 @@ &qupv3_id_0 {
>   	status = "okay";
>   };
>   
> +&qupv3_id_2 {
> +	status = "okay";
> +};
> +
>   &slpi {
>   	status = "okay";
>   	firmware-name = "qcom/sm8350/slpi.mbn";
> @@ -544,4 +636,18 @@ usb_hub_enabled_state: usb-hub-enabled-state {
>   		drive-strength = <2>;
>   		output-low;
>   	};
> +
> +	lt9611_rst_pin: lt9611-rst-state {
> +		pins = "gpio48";
> +		function = "normal";
> +
> +		output-high;
> +		input-disable;
> +	};
> +
> +	lt9611_irq_pin: lt9611-irq {
> +		pins = "gpio50";
> +		function = "gpio";
> +		bias-disable;
> +	};
>   };
Bjorn Andersson Oct. 28, 2022, 1:57 p.m. UTC | #2
On Fri, Oct 28, 2022 at 02:08:12PM +0200, Robert Foss wrote:
> The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.
> 
> In order to toggle the board to enable the HDMI output,
> switch #7 & #8 on the rightmost multi-switch package have
> to be toggled to On.
> 
> Signed-off-by: Robert Foss <robert.foss@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 106 ++++++++++++++++++++++++
>  1 file changed, 106 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 6e07feb4b3b2..6666b38b58f8 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -20,6 +20,17 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	hdmi-out {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&lt9611_out>;
> +			};
> +		};
> +	};
> +
>  	vph_pwr: vph-pwr-regulator {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vph_pwr";
> @@ -29,6 +40,32 @@ vph_pwr: vph-pwr-regulator {
>  		regulator-always-on;
>  		regulator-boot-on;
>  	};
> +
> +	lt9611_1v2: lt9611-1v2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_1V2";
> +
> +		vin-supply = <&vph_pwr>;
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-boot-on;
> +		regulator-always-on;

Why is this always-on?

> +	};
> +
> +	lt9611_3v3: lt9611-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_3V3";
> +
> +		vin-supply = <&vreg_bob>;
> +		gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
>  };
>  
>  &adsp {
> @@ -220,6 +257,15 @@ &dispcc {
>  &dsi0 {
>  	status = "okay";
>  	vdda-supply = <&vreg_l6b_1p2>;
> +
> +	ports {
> +		port@1 {
> +			endpoint {
> +				remote-endpoint = <&lt9611_a>;
> +				data-lanes = <0 1 2 3>;
> +			};
> +		};
> +	};
>  };
>  
>  &dsi0_phy  {
> @@ -231,6 +277,48 @@ &gpi_dma1 {
>  	status = "okay";
>  };
>  
> +&i2c15 {
> +	status = "okay";

Please keep status last. (Yes I see that it goes against the convention
in this file, so let's update that at some point as well)

> +	clock-frequency = <400000>;
> +
> +	lt9611_codec: hdmi-bridge@2b {
> +		compatible = "lontium,lt9611uxc";
> +		reg = <0x2b>;
> +		status = "okay";

This is the default, you can omit it.

> +
> +		interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
> +		reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
> +
> +		vdd-supply = <&lt9611_1v2>;
> +		vcc-supply = <&lt9611_3v3>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				lt9611_a: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +
> +				lt9611_out: endpoint {
> +					remote-endpoint = <&hdmi_con>;
> +				};
> +			};
> +
> +		};
> +	};
> +};
> +
>  &mdss {
>  	status = "okay";
>  };
> @@ -248,6 +336,10 @@ &qupv3_id_0 {
>  	status = "okay";
>  };
>  
> +&qupv3_id_2 {
> +	status = "okay";
> +};
> +
>  &slpi {
>  	status = "okay";
>  	firmware-name = "qcom/sm8350/slpi.mbn";
> @@ -544,4 +636,18 @@ usb_hub_enabled_state: usb-hub-enabled-state {
>  		drive-strength = <2>;
>  		output-low;
>  	};
> +
> +	lt9611_rst_pin: lt9611-rst-state {
> +		pins = "gpio48";
> +		function = "normal";
> +
> +		output-high;
> +		input-disable;
> +	};
> +
> +	lt9611_irq_pin: lt9611-irq {

pinctrl state nodes should be suffixed with "-state".

And you can lump the two pins into a single -state, with rst-pins and
irq-pins as subnodes, defining the two pins.

Regards,
Bjorn

> +		pins = "gpio50";
> +		function = "gpio";
> +		bias-disable;
> +	};
>  };
> -- 
> 2.34.1
>
Krzysztof Kozlowski Oct. 28, 2022, 10:05 p.m. UTC | #3
On 28/10/2022 08:08, Robert Foss wrote:
> The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.
> 
> In order to toggle the board to enable the HDMI output,
> switch #7 & #8 on the rightmost multi-switch package have
> to be toggled to On.
> 
> Signed-off-by: Robert Foss <robert.foss@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 106 ++++++++++++++++++++++++
>  1 file changed, 106 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 6e07feb4b3b2..6666b38b58f8 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -20,6 +20,17 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	hdmi-out {

Generic node names, so hdmi-connector or just connector.

> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&lt9611_out>;
> +			};
> +		};
> +	};
> +
>  	vph_pwr: vph-pwr-regulator {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vph_pwr";
> @@ -29,6 +40,32 @@ vph_pwr: vph-pwr-regulator {
>  		regulator-always-on;
>  		regulator-boot-on;
>  	};
> +
> +	lt9611_1v2: lt9611-1v2 {

Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_1V2";
> +
> +		vin-supply = <&vph_pwr>;
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	lt9611_3v3: lt9611-3v3 {

Ditto


> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_3V3";
> +
> +		vin-supply = <&vreg_bob>;
> +		gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
>  };
>  
>  &adsp {
> @@ -220,6 +257,15 @@ &dispcc {
>  &dsi0 {
>  	status = "okay";
>  	vdda-supply = <&vreg_l6b_1p2>;
> +
> +	ports {
> +		port@1 {
> +			endpoint {
> +				remote-endpoint = <&lt9611_a>;
> +				data-lanes = <0 1 2 3>;
> +			};
> +		};
> +	};
>  };
>  
>  &dsi0_phy  {
> @@ -231,6 +277,48 @@ &gpi_dma1 {
>  	status = "okay";
>  };
>  
> +&i2c15 {
> +	status = "okay";

status is the last property

> +	clock-frequency = <400000>;
> +
> +	lt9611_codec: hdmi-bridge@2b {
> +		compatible = "lontium,lt9611uxc";
> +		reg = <0x2b>;
> +		status = "okay";

Why status?

> +
> +		interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
> +		reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
> +
> +		vdd-supply = <&lt9611_1v2>;
> +		vcc-supply = <&lt9611_3v3>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				lt9611_a: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +
> +				lt9611_out: endpoint {
> +					remote-endpoint = <&hdmi_con>;
> +				};
> +			};
> +

No need for blank line

> +		};
> +	};
> +};
> +
>  &mdss {
>  	status = "okay";
>  };
> @@ -248,6 +336,10 @@ &qupv3_id_0 {
>  	status = "okay";
>  };
>  
> +&qupv3_id_2 {
> +	status = "okay";
> +};
> +
>  &slpi {
>  	status = "okay";
>  	firmware-name = "qcom/sm8350/slpi.mbn";
> @@ -544,4 +636,18 @@ usb_hub_enabled_state: usb-hub-enabled-state {
>  		drive-strength = <2>;
>  		output-low;
>  	};
> +
> +	lt9611_rst_pin: lt9611-rst-state {
> +		pins = "gpio48";
> +		function = "normal";
> +
> +		output-high;
> +		input-disable;
> +	};
> +
> +	lt9611_irq_pin: lt9611-irq {

Missing suffix 'state'.

Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).

Rebase your changes on last linux-next.

Best regards,
Krzysztof
Dmitry Baryshkov Nov. 3, 2022, 2:19 p.m. UTC | #4
On 28/10/2022 16:56, Dmitry Baryshkov wrote:
> On 28/10/2022 15:08, Robert Foss wrote:
>> The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.
>>
>> In order to toggle the board to enable the HDMI output,
>> switch #7 & #8 on the rightmost multi-switch package have
>> to be toggled to On.
> 
> Since this doesn't look like a default setup, it would probably make 
> sense to move this to new sm8350-hdk-hdmi.dts with the comment regarding 
> necessary switch changes at the top of the file.
> 

Please excuse me here. I checked the Lantronix site. It clearly names 
'Optional Display/Expansion board mates to DSI connectors'. So, you were 
correct, the HDMI should be in the base setup, while DSI panel should 
come as the extending DT file.
Robert Foss Nov. 11, 2022, 3:18 p.m. UTC | #5
On Fri, 28 Oct 2022 at 15:57, Bjorn Andersson <andersson@kernel.org> wrote:
>
> On Fri, Oct 28, 2022 at 02:08:12PM +0200, Robert Foss wrote:
> > The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.
> >
> > In order to toggle the board to enable the HDMI output,
> > switch #7 & #8 on the rightmost multi-switch package have
> > to be toggled to On.
> >
> > Signed-off-by: Robert Foss <robert.foss@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 106 ++++++++++++++++++++++++
> >  1 file changed, 106 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> > index 6e07feb4b3b2..6666b38b58f8 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> > +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> > @@ -20,6 +20,17 @@ chosen {
> >               stdout-path = "serial0:115200n8";
> >       };
> >
> > +     hdmi-out {
> > +             compatible = "hdmi-connector";
> > +             type = "a";
> > +
> > +             port {
> > +                     hdmi_con: endpoint {
> > +                             remote-endpoint = <&lt9611_out>;
> > +                     };
> > +             };
> > +     };
> > +
> >       vph_pwr: vph-pwr-regulator {
> >               compatible = "regulator-fixed";
> >               regulator-name = "vph_pwr";
> > @@ -29,6 +40,32 @@ vph_pwr: vph-pwr-regulator {
> >               regulator-always-on;
> >               regulator-boot-on;
> >       };
> > +
> > +     lt9611_1v2: lt9611-1v2 {
> > +             compatible = "regulator-fixed";
> > +             regulator-name = "LT9611_1V2";
> > +
> > +             vin-supply = <&vph_pwr>;
> > +             regulator-min-microvolt = <1200000>;
> > +             regulator-max-microvolt = <1200000>;
> > +             gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
> > +             enable-active-high;
> > +             regulator-boot-on;
> > +             regulator-always-on;
>
> Why is this always-on?

It shouldn't be. Removing this in v2.

>
> > +     };
> > +
> > +     lt9611_3v3: lt9611-3v3 {
> > +             compatible = "regulator-fixed";
> > +             regulator-name = "LT9611_3V3";
> > +
> > +             vin-supply = <&vreg_bob>;
> > +             gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
> > +             regulator-min-microvolt = <3300000>;
> > +             regulator-max-microvolt = <3300000>;
> > +             enable-active-high;
> > +             regulator-boot-on;
> > +             regulator-always-on;
> > +     };
> >  };
> >
> >  &adsp {
> > @@ -220,6 +257,15 @@ &dispcc {
> >  &dsi0 {
> >       status = "okay";
> >       vdda-supply = <&vreg_l6b_1p2>;
> > +
> > +     ports {
> > +             port@1 {
> > +                     endpoint {
> > +                             remote-endpoint = <&lt9611_a>;
> > +                             data-lanes = <0 1 2 3>;
> > +                     };
> > +             };
> > +     };
> >  };
> >
> >  &dsi0_phy  {
> > @@ -231,6 +277,48 @@ &gpi_dma1 {
> >       status = "okay";
> >  };
> >
> > +&i2c15 {
> > +     status = "okay";
>
> Please keep status last. (Yes I see that it goes against the convention
> in this file, so let's update that at some point as well)

Ack.

>
> > +     clock-frequency = <400000>;
> > +
> > +     lt9611_codec: hdmi-bridge@2b {
> > +             compatible = "lontium,lt9611uxc";
> > +             reg = <0x2b>;
> > +             status = "okay";
>
> This is the default, you can omit it.

Ack.

>
> > +
> > +             interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
> > +             reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
> > +
> > +             vdd-supply = <&lt9611_1v2>;
> > +             vcc-supply = <&lt9611_3v3>;
> > +
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> > +
> > +             ports {
> > +                     #address-cells = <1>;
> > +                     #size-cells = <0>;
> > +
> > +                     port@0 {
> > +                             reg = <0>;
> > +
> > +                             lt9611_a: endpoint {
> > +                                     remote-endpoint = <&dsi0_out>;
> > +                             };
> > +                     };
> > +
> > +                     port@2 {
> > +                             reg = <2>;
> > +
> > +                             lt9611_out: endpoint {
> > +                                     remote-endpoint = <&hdmi_con>;
> > +                             };
> > +                     };
> > +
> > +             };
> > +     };
> > +};
> > +
> >  &mdss {
> >       status = "okay";
> >  };
> > @@ -248,6 +336,10 @@ &qupv3_id_0 {
> >       status = "okay";
> >  };
> >
> > +&qupv3_id_2 {
> > +     status = "okay";
> > +};
> > +
> >  &slpi {
> >       status = "okay";
> >       firmware-name = "qcom/sm8350/slpi.mbn";
> > @@ -544,4 +636,18 @@ usb_hub_enabled_state: usb-hub-enabled-state {
> >               drive-strength = <2>;
> >               output-low;
> >       };
> > +
> > +     lt9611_rst_pin: lt9611-rst-state {
> > +             pins = "gpio48";
> > +             function = "normal";
> > +
> > +             output-high;
> > +             input-disable;
> > +     };
> > +
> > +     lt9611_irq_pin: lt9611-irq {
>
> pinctrl state nodes should be suffixed with "-state".
>
> And you can lump the two pins into a single -state, with rst-pins and
> irq-pins as subnodes, defining the two pins.
>
> Regards,
> Bjorn
>
> > +             pins = "gpio50";
> > +             function = "gpio";
> > +             bias-disable;
> > +     };
> >  };
> > --
> > 2.34.1
> >
Robert Foss Nov. 11, 2022, 3:20 p.m. UTC | #6
On Sat, 29 Oct 2022 at 00:06, Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
>
> On 28/10/2022 08:08, Robert Foss wrote:
> > The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.
> >
> > In order to toggle the board to enable the HDMI output,
> > switch #7 & #8 on the rightmost multi-switch package have
> > to be toggled to On.
> >
> > Signed-off-by: Robert Foss <robert.foss@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 106 ++++++++++++++++++++++++
> >  1 file changed, 106 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> > index 6e07feb4b3b2..6666b38b58f8 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> > +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> > @@ -20,6 +20,17 @@ chosen {
> >               stdout-path = "serial0:115200n8";
> >       };
> >
> > +     hdmi-out {
>
> Generic node names, so hdmi-connector or just connector.

Ack.

>
> > +             compatible = "hdmi-connector";
> > +             type = "a";
> > +
> > +             port {
> > +                     hdmi_con: endpoint {
> > +                             remote-endpoint = <&lt9611_out>;
> > +                     };
> > +             };
> > +     };
> > +
> >       vph_pwr: vph-pwr-regulator {
> >               compatible = "regulator-fixed";
> >               regulator-name = "vph_pwr";
> > @@ -29,6 +40,32 @@ vph_pwr: vph-pwr-regulator {
> >               regulator-always-on;
> >               regulator-boot-on;
> >       };
> > +
> > +     lt9611_1v2: lt9611-1v2 {
>
> Node names should be generic.
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

Ack.

>
> > +             compatible = "regulator-fixed";
> > +             regulator-name = "LT9611_1V2";
> > +
> > +             vin-supply = <&vph_pwr>;
> > +             regulator-min-microvolt = <1200000>;
> > +             regulator-max-microvolt = <1200000>;
> > +             gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
> > +             enable-active-high;
> > +             regulator-boot-on;
> > +             regulator-always-on;
> > +     };
> > +
> > +     lt9611_3v3: lt9611-3v3 {
>
> Ditto

Ack.

>
>
> > +             compatible = "regulator-fixed";
> > +             regulator-name = "LT9611_3V3";
> > +
> > +             vin-supply = <&vreg_bob>;
> > +             gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
> > +             regulator-min-microvolt = <3300000>;
> > +             regulator-max-microvolt = <3300000>;
> > +             enable-active-high;
> > +             regulator-boot-on;
> > +             regulator-always-on;
> > +     };
> >  };
> >
> >  &adsp {
> > @@ -220,6 +257,15 @@ &dispcc {
> >  &dsi0 {
> >       status = "okay";
> >       vdda-supply = <&vreg_l6b_1p2>;
> > +
> > +     ports {
> > +             port@1 {
> > +                     endpoint {
> > +                             remote-endpoint = <&lt9611_a>;
> > +                             data-lanes = <0 1 2 3>;
> > +                     };
> > +             };
> > +     };
> >  };
> >
> >  &dsi0_phy  {
> > @@ -231,6 +277,48 @@ &gpi_dma1 {
> >       status = "okay";
> >  };
> >
> > +&i2c15 {
> > +     status = "okay";
>
> status is the last property

Ack.

>
> > +     clock-frequency = <400000>;
> > +
> > +     lt9611_codec: hdmi-bridge@2b {
> > +             compatible = "lontium,lt9611uxc";
> > +             reg = <0x2b>;
> > +             status = "okay";
>
> Why status?

It should be removed. Fixing in v2.

>
> > +
> > +             interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
> > +             reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
> > +
> > +             vdd-supply = <&lt9611_1v2>;
> > +             vcc-supply = <&lt9611_3v3>;
> > +
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> > +
> > +             ports {
> > +                     #address-cells = <1>;
> > +                     #size-cells = <0>;
> > +
> > +                     port@0 {
> > +                             reg = <0>;
> > +
> > +                             lt9611_a: endpoint {
> > +                                     remote-endpoint = <&dsi0_out>;
> > +                             };
> > +                     };
> > +
> > +                     port@2 {
> > +                             reg = <2>;
> > +
> > +                             lt9611_out: endpoint {
> > +                                     remote-endpoint = <&hdmi_con>;
> > +                             };
> > +                     };
> > +
>
> No need for blank line

Ack

>
> > +             };
> > +     };
> > +};
> > +
> >  &mdss {
> >       status = "okay";
> >  };
> > @@ -248,6 +336,10 @@ &qupv3_id_0 {
> >       status = "okay";
> >  };
> >
> > +&qupv3_id_2 {
> > +     status = "okay";
> > +};
> > +
> >  &slpi {
> >       status = "okay";
> >       firmware-name = "qcom/sm8350/slpi.mbn";
> > @@ -544,4 +636,18 @@ usb_hub_enabled_state: usb-hub-enabled-state {
> >               drive-strength = <2>;
> >               output-low;
> >       };
> > +
> > +     lt9611_rst_pin: lt9611-rst-state {
> > +             pins = "gpio48";
> > +             function = "normal";
> > +
> > +             output-high;
> > +             input-disable;
> > +     };
> > +
> > +     lt9611_irq_pin: lt9611-irq {
>
> Missing suffix 'state'.

Ack.

>
> Does not look like you tested the DTS against bindings. Please run `make
> dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
> for instructions).

v1 was missing the bindings, v2 will include bindings for there parts.

>
> Rebase your changes on last linux-next.

Ack.

>
> Best regards,
> Krzysztof
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
index 6e07feb4b3b2..6666b38b58f8 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -20,6 +20,17 @@  chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -29,6 +40,32 @@  vph_pwr: vph-pwr-regulator {
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	lt9611_1v2: lt9611-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V2";
+
+		vin-supply = <&vph_pwr>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	lt9611_3v3: lt9611-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_3V3";
+
+		vin-supply = <&vreg_bob>;
+		gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &adsp {
@@ -220,6 +257,15 @@  &dispcc {
 &dsi0 {
 	status = "okay";
 	vdda-supply = <&vreg_l6b_1p2>;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
 };
 
 &dsi0_phy  {
@@ -231,6 +277,48 @@  &gpi_dma1 {
 	status = "okay";
 };
 
+&i2c15 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	lt9611_codec: hdmi-bridge@2b {
+		compatible = "lontium,lt9611uxc";
+		reg = <0x2b>;
+		status = "okay";
+
+		interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&lt9611_1v2>;
+		vcc-supply = <&lt9611_3v3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+
+		};
+	};
+};
+
 &mdss {
 	status = "okay";
 };
@@ -248,6 +336,10 @@  &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_2 {
+	status = "okay";
+};
+
 &slpi {
 	status = "okay";
 	firmware-name = "qcom/sm8350/slpi.mbn";
@@ -544,4 +636,18 @@  usb_hub_enabled_state: usb-hub-enabled-state {
 		drive-strength = <2>;
 		output-low;
 	};
+
+	lt9611_rst_pin: lt9611-rst-state {
+		pins = "gpio48";
+		function = "normal";
+
+		output-high;
+		input-disable;
+	};
+
+	lt9611_irq_pin: lt9611-irq {
+		pins = "gpio50";
+		function = "gpio";
+		bias-disable;
+	};
 };