| Message ID | 20221109142623.53052-3-konrad.dybcio@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | SM6375 / PDX225 SD Card support | expand |
On 09/11/2022 15:26, Konrad Dybcio wrote: > Configure the second SDHCI bus controller, which usually the > interface used for SD cards. > > Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm6375.dtsi | 82 ++++++++++++++++++++++++++++ > 1 file changed, 82 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sm6375.dtsi b/arch/arm64/boot/dts/qcom/sm6375.dtsi > index 6adffd927a8e..483202e60cd7 100644 > --- a/arch/arm64/boot/dts/qcom/sm6375.dtsi > +++ b/arch/arm64/boot/dts/qcom/sm6375.dtsi > @@ -540,6 +540,46 @@ tlmm: pinctrl@500000 { > #interrupt-cells = <2>; > #gpio-cells = <2>; > > + sdc2_off_state: sdc2-off-state { > + clk-pins { > + pins = "sdc2_clk"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + cmd-pins { > + pins = "sdc2_cmd"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + data-pins { > + pins = "sdc2_data"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + }; > + > + sdc2_on_state: sdc2-on-state { > + clk-pins { > + pins = "sdc2_clk"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + cmd-pins { > + pins = "sdc2_cmd"; > + drive-strength = <10>; > + bias-pull-up; > + }; > + > + data-pins { > + pins = "sdc2_data"; > + drive-strength = <10>; > + bias-pull-up; > + }; > + }; > + > qup_i2c0_default: qup-i2c0-default-state { > pins = "gpio0", "gpio1"; > function = "qup00"; > @@ -630,6 +670,48 @@ rpm_msg_ram: sram@45f0000 { > reg = <0 0x045f0000 0 0x7000>; > }; > > + sdhc_2: sdhci@4784000 { Node name: mmc > + compatible = "qcom,sm6375-sdhci", "qcom,sdhci-msm-v5"; > + reg = <0 0x04784000 0 0x1000>; > + Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/qcom/sm6375.dtsi b/arch/arm64/boot/dts/qcom/sm6375.dtsi index 6adffd927a8e..483202e60cd7 100644 --- a/arch/arm64/boot/dts/qcom/sm6375.dtsi +++ b/arch/arm64/boot/dts/qcom/sm6375.dtsi @@ -540,6 +540,46 @@ tlmm: pinctrl@500000 { #interrupt-cells = <2>; #gpio-cells = <2>; + sdc2_off_state: sdc2-off-state { + clk-pins { + pins = "sdc2_clk"; + drive-strength = <2>; + bias-disable; + }; + + cmd-pins { + pins = "sdc2_cmd"; + drive-strength = <2>; + bias-pull-up; + }; + + data-pins { + pins = "sdc2_data"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + sdc2_on_state: sdc2-on-state { + clk-pins { + pins = "sdc2_clk"; + drive-strength = <16>; + bias-disable; + }; + + cmd-pins { + pins = "sdc2_cmd"; + drive-strength = <10>; + bias-pull-up; + }; + + data-pins { + pins = "sdc2_data"; + drive-strength = <10>; + bias-pull-up; + }; + }; + qup_i2c0_default: qup-i2c0-default-state { pins = "gpio0", "gpio1"; function = "qup00"; @@ -630,6 +670,48 @@ rpm_msg_ram: sram@45f0000 { reg = <0 0x045f0000 0 0x7000>; }; + sdhc_2: sdhci@4784000 { + compatible = "qcom,sm6375-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x04784000 0 0x1000>; + + interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_AHB_CLK>, + <&gcc GCC_SDCC2_APPS_CLK>, + <&rpmcc RPM_SMD_XO_CLK_SRC>; + clock-names = "iface", "core", "xo"; + resets = <&gcc GCC_SDCC2_BCR>; + iommus = <&apps_smmu 0x40 0x0>; + + pinctrl-0 = <&sdc2_on_state>; + pinctrl-1 = <&sdc2_off_state>; + pinctrl-names = "default", "sleep"; + + qcom,dll-config = <0x0007642c>; + qcom,ddr-config = <0x80040868>; + power-domains = <&rpmpd SM6375_VDDCX>; + operating-points-v2 = <&sdhc2_opp_table>; + bus-width = <4>; + + status = "disabled"; + + sdhc2_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + required-opps = <&rpmpd_opp_low_svs>; + }; + + opp-202000000 { + opp-hz = /bits/ 64 <202000000>; + required-opps = <&rpmpd_opp_svs_plus>; + }; + }; + }; + gpi_dma0: dma-controller@4a00000 { compatible = "qcom,sm6375-gpi-dma", "qcom,sm6350-gpi-dma"; reg = <0 0x04a00000 0 0x60000>;
Configure the second SDHCI bus controller, which usually the interface used for SD cards. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/sm6375.dtsi | 82 ++++++++++++++++++++++++++++ 1 file changed, 82 insertions(+)