diff mbox series

[v2,10/12] arm64: dts: qcom: sm8350: Add display system nodes

Message ID 20221115133105.980877-11-robert.foss@linaro.org (mailing list archive)
State Superseded
Headers show
Series Enable Display for SM8350 | expand

Commit Message

Robert Foss Nov. 15, 2022, 1:31 p.m. UTC
Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
nodes the display subsystem is configured to support
one DSI output.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8350.dtsi | 197 ++++++++++++++++++++++++++-
 1 file changed, 193 insertions(+), 4 deletions(-)

Comments

Konrad Dybcio Nov. 15, 2022, 1:47 p.m. UTC | #1
On 15/11/2022 14:31, Robert Foss wrote:
> Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
> nodes the display subsystem is configured to support
> one DSI output.
> 
> Signed-off-by: Robert Foss <robert.foss@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8350.dtsi | 197 ++++++++++++++++++++++++++-
>   1 file changed, 193 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> index 434f8e8b12c1..5c98e5cf5ad0 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> @@ -3,6 +3,7 @@
>    * Copyright (c) 2020, Linaro Limited
>    */
>   
> +#include <dt-bindings/interconnect/qcom,sm8350.h>
>   #include <dt-bindings/interrupt-controller/arm-gic.h>
>   #include <dt-bindings/clock/qcom,dispcc-sm8350.h>
>   #include <dt-bindings/clock/qcom,gcc-sm8350.h>
> @@ -2536,14 +2537,201 @@ usb_2_dwc3: usb@a800000 {
>   			};
>   		};
>   
> +		mdss: mdss@ae00000 {
> +			compatible = "qcom,sm8350-mdss";
> +			reg = <0 0x0ae00000 0 0x1000>;
> +			reg-names = "mdss";
> +
> +			interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
> +					<&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
> +			interconnect-names = "mdp0-mem", "mdp1-mem";
> +
> +			power-domains = <&dispcc MDSS_GDSC>;
> +			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> +
> +			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_DISP_HF_AXI_CLK>,
> +				 <&gcc GCC_DISP_SF_AXI_CLK>,
> +				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
> +			clock-names = "iface", "bus", "nrt_bus", "core";
> +
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +
> +			iommus = <&apps_smmu 0x820 0x402>;
> +
> +			status = "disabled";
> +
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +
> +			mdss_mdp: display-controller@ae01000 {
> +				compatible = "qcom,sm8350-dpu";
> +				reg = <0 0x0ae01000 0 0x8f000>,
> +				      <0 0x0aeb0000 0 0x2008>;
> +				reg-names = "mdp", "vbif";
> +
> +				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> +					<&gcc GCC_DISP_SF_AXI_CLK>,
> +					<&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> +					<&dispcc DISP_CC_MDSS_MDP_CLK>,
> +					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				clock-names = "bus",
> +					      "nrt_bus",
> +					      "iface",
> +					      "lut",
> +					      "core",
> +					      "vsync";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				assigned-clock-rates = <19200000>;
> +
> +				operating-points-v2 = <&mdp_opp_table>;
> +				power-domains = <&rpmhpd SM8350_MMCX>;
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <0>;
> +
> +				status = "disabled";
It doesn't make sense to disable mdp separately, as mdss is essentially 
useless without it.

> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dpu_intf1_out: endpoint {
> +							remote-endpoint = <&dsi0_in>;
> +						};
> +					};
> +				};
> +
> +				mdp_opp_table: opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-200000000 {
> +						opp-hz = /bits/ 64 <200000000>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-300000000 {
> +						opp-hz = /bits/ 64 <300000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-345000000 {
> +						opp-hz = /bits/ 64 <345000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +
> +					opp-460000000 {
> +						opp-hz = /bits/ 64 <460000000>;
> +						required-opps = <&rpmhpd_opp_nom>;
> +					};
> +				};
> +			};
> +
> +			dsi0: dsi@ae94000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae94000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <4>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
> +						  <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> +				assigned-clock-parents = <&dsi0_phy 0>,
> +							 <&dsi0_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8350_MMCX>;
> +
> +				phys = <&dsi0_phy>;
> +				phy-names = "dsi";
I think that was dropped as of late.

> +
> +				status = "disabled";
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dsi0_in: endpoint {
> +							remote-endpoint = <&dpu_intf1_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dsi0_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi0_phy: phy@ae94400 {
> +				compatible = "qcom,dsi-phy-5nm-8350";
> +				reg = <0 0x0ae94400 0 0x200>,
> +				      <0 0x0ae94600 0 0x280>,
> +				      <0 0x0ae94900 0 0x260>;
> +				reg-names = "dsi_phy",
> +					    "dsi_phy_lane",
> +					    "dsi_pll";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "iface", "ref";
> +
> +				status = "disabled";
> +
> +				dsi_opp_table: dsi-opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-187500000 {
> +						opp-hz = /bits/ 64 <187500000>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-300000000 {
> +						opp-hz = /bits/ 64 <300000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-358000000 {
> +						opp-hz = /bits/ 64 <358000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +				};
> +			};
> +		};
> +
>   		dispcc: clock-controller@af00000 {
>   			compatible = "qcom,sm8350-dispcc";
>   			reg = <0 0x0af00000 0 0x10000>;
>   			clocks = <&rpmhcc RPMH_CXO_CLK>,
> -				 <0>,
> -				 <0>,
> -				 <0>,
> -				 <0>,
> +				 <&dsi0_phy 0>, <&dsi0_phy 1>,
> +				 <0>, <0>,
>   				 <0>,
>   				 <0>;
>   			clock-names = "bi_tcxo",
> @@ -2558,6 +2746,7 @@ dispcc: clock-controller@af00000 {
>   			#power-domain-cells = <1>;
>   
>   			power-domains = <&rpmhpd SM8350_MMCX>;
> +			required-opps = <&rpmhpd_opp_turbo>;
A turbo vote is required for it to function? Seems a bit high..

Konrad
>   		};
>   
>   		adsp: remoteproc@17300000 {
Robert Foss Nov. 29, 2022, 4:47 p.m. UTC | #2
On Tue, 15 Nov 2022 at 14:47, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
>
>
> On 15/11/2022 14:31, Robert Foss wrote:
> > Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
> > nodes the display subsystem is configured to support
> > one DSI output.
> >
> > Signed-off-by: Robert Foss <robert.foss@linaro.org>
> > ---
> >   arch/arm64/boot/dts/qcom/sm8350.dtsi | 197 ++++++++++++++++++++++++++-
> >   1 file changed, 193 insertions(+), 4 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > index 434f8e8b12c1..5c98e5cf5ad0 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > @@ -3,6 +3,7 @@
> >    * Copyright (c) 2020, Linaro Limited
> >    */
> >
> > +#include <dt-bindings/interconnect/qcom,sm8350.h>
> >   #include <dt-bindings/interrupt-controller/arm-gic.h>
> >   #include <dt-bindings/clock/qcom,dispcc-sm8350.h>
> >   #include <dt-bindings/clock/qcom,gcc-sm8350.h>
> > @@ -2536,14 +2537,201 @@ usb_2_dwc3: usb@a800000 {
> >                       };
> >               };
> >
> > +             mdss: mdss@ae00000 {
> > +                     compatible = "qcom,sm8350-mdss";
> > +                     reg = <0 0x0ae00000 0 0x1000>;
> > +                     reg-names = "mdss";
> > +
> > +                     interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
> > +                                     <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
> > +                     interconnect-names = "mdp0-mem", "mdp1-mem";
> > +
> > +                     power-domains = <&dispcc MDSS_GDSC>;
> > +                     resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> > +
> > +                     clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +                              <&gcc GCC_DISP_HF_AXI_CLK>,
> > +                              <&gcc GCC_DISP_SF_AXI_CLK>,
> > +                              <&dispcc DISP_CC_MDSS_MDP_CLK>;
> > +                     clock-names = "iface", "bus", "nrt_bus", "core";
> > +
> > +                     interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> > +                     interrupt-controller;
> > +                     #interrupt-cells = <1>;
> > +
> > +                     iommus = <&apps_smmu 0x820 0x402>;
> > +
> > +                     status = "disabled";
> > +
> > +                     #address-cells = <2>;
> > +                     #size-cells = <2>;
> > +                     ranges;
> > +
> > +                     mdss_mdp: display-controller@ae01000 {
> > +                             compatible = "qcom,sm8350-dpu";
> > +                             reg = <0 0x0ae01000 0 0x8f000>,
> > +                                   <0 0x0aeb0000 0 0x2008>;
> > +                             reg-names = "mdp", "vbif";
> > +
> > +                             clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> > +                                     <&gcc GCC_DISP_SF_AXI_CLK>,
> > +                                     <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +                                     <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> > +                                     <&dispcc DISP_CC_MDSS_MDP_CLK>,
> > +                                     <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> > +                             clock-names = "bus",
> > +                                           "nrt_bus",
> > +                                           "iface",
> > +                                           "lut",
> > +                                           "core",
> > +                                           "vsync";
> > +
> > +                             assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> > +                             assigned-clock-rates = <19200000>;
> > +
> > +                             operating-points-v2 = <&mdp_opp_table>;
> > +                             power-domains = <&rpmhpd SM8350_MMCX>;
> > +
> > +                             interrupt-parent = <&mdss>;
> > +                             interrupts = <0>;
> > +
> > +                             status = "disabled";
> It doesn't make sense to disable mdp separately, as mdss is essentially
> useless without it.

Ack

>
> > +
> > +                             ports {
> > +                                     #address-cells = <1>;
> > +                                     #size-cells = <0>;
> > +
> > +                                     port@0 {
> > +                                             reg = <0>;
> > +                                             dpu_intf1_out: endpoint {
> > +                                                     remote-endpoint = <&dsi0_in>;
> > +                                             };
> > +                                     };
> > +                             };
> > +
> > +                             mdp_opp_table: opp-table {
> > +                                     compatible = "operating-points-v2";
> > +
> > +                                     opp-200000000 {
> > +                                             opp-hz = /bits/ 64 <200000000>;
> > +                                             required-opps = <&rpmhpd_opp_low_svs>;
> > +                                     };
> > +
> > +                                     opp-300000000 {
> > +                                             opp-hz = /bits/ 64 <300000000>;
> > +                                             required-opps = <&rpmhpd_opp_svs>;
> > +                                     };
> > +
> > +                                     opp-345000000 {
> > +                                             opp-hz = /bits/ 64 <345000000>;
> > +                                             required-opps = <&rpmhpd_opp_svs_l1>;
> > +                                     };
> > +
> > +                                     opp-460000000 {
> > +                                             opp-hz = /bits/ 64 <460000000>;
> > +                                             required-opps = <&rpmhpd_opp_nom>;
> > +                                     };
> > +                             };
> > +                     };
> > +
> > +                     dsi0: dsi@ae94000 {
> > +                             compatible = "qcom,mdss-dsi-ctrl";
> > +                             reg = <0 0x0ae94000 0 0x400>;
> > +                             reg-names = "dsi_ctrl";
> > +
> > +                             interrupt-parent = <&mdss>;
> > +                             interrupts = <4>;
> > +
> > +                             clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> > +                                      <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> > +                                      <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> > +                                      <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> > +                                      <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +                                      <&gcc GCC_DISP_HF_AXI_CLK>;
> > +                             clock-names = "byte",
> > +                                           "byte_intf",
> > +                                           "pixel",
> > +                                           "core",
> > +                                           "iface",
> > +                                           "bus";
> > +
> > +                             assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
> > +                                               <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> > +                             assigned-clock-parents = <&dsi0_phy 0>,
> > +                                                      <&dsi0_phy 1>;
> > +
> > +                             operating-points-v2 = <&dsi_opp_table>;
> > +                             power-domains = <&rpmhpd SM8350_MMCX>;
> > +
> > +                             phys = <&dsi0_phy>;
> > +                             phy-names = "dsi";
> I think that was dropped as of late.

Ack

>
> > +
> > +                             status = "disabled";
> > +
> > +                             ports {
> > +                                     #address-cells = <1>;
> > +                                     #size-cells = <0>;
> > +
> > +                                     port@0 {
> > +                                             reg = <0>;
> > +                                             dsi0_in: endpoint {
> > +                                                     remote-endpoint = <&dpu_intf1_out>;
> > +                                             };
> > +                                     };
> > +
> > +                                     port@1 {
> > +                                             reg = <1>;
> > +                                             dsi0_out: endpoint {
> > +                                             };
> > +                                     };
> > +                             };
> > +                     };
> > +
> > +                     dsi0_phy: phy@ae94400 {
> > +                             compatible = "qcom,dsi-phy-5nm-8350";
> > +                             reg = <0 0x0ae94400 0 0x200>,
> > +                                   <0 0x0ae94600 0 0x280>,
> > +                                   <0 0x0ae94900 0 0x260>;
> > +                             reg-names = "dsi_phy",
> > +                                         "dsi_phy_lane",
> > +                                         "dsi_pll";
> > +
> > +                             #clock-cells = <1>;
> > +                             #phy-cells = <0>;
> > +
> > +                             clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +                                      <&rpmhcc RPMH_CXO_CLK>;
> > +                             clock-names = "iface", "ref";
> > +
> > +                             status = "disabled";
> > +
> > +                             dsi_opp_table: dsi-opp-table {
> > +                                     compatible = "operating-points-v2";
> > +
> > +                                     opp-187500000 {
> > +                                             opp-hz = /bits/ 64 <187500000>;
> > +                                             required-opps = <&rpmhpd_opp_low_svs>;
> > +                                     };
> > +
> > +                                     opp-300000000 {
> > +                                             opp-hz = /bits/ 64 <300000000>;
> > +                                             required-opps = <&rpmhpd_opp_svs>;
> > +                                     };
> > +
> > +                                     opp-358000000 {
> > +                                             opp-hz = /bits/ 64 <358000000>;
> > +                                             required-opps = <&rpmhpd_opp_svs_l1>;
> > +                                     };
> > +                             };
> > +                     };
> > +             };
> > +
> >               dispcc: clock-controller@af00000 {
> >                       compatible = "qcom,sm8350-dispcc";
> >                       reg = <0 0x0af00000 0 0x10000>;
> >                       clocks = <&rpmhcc RPMH_CXO_CLK>,
> > -                              <0>,
> > -                              <0>,
> > -                              <0>,
> > -                              <0>,
> > +                              <&dsi0_phy 0>, <&dsi0_phy 1>,
> > +                              <0>, <0>,
> >                                <0>,
> >                                <0>;
> >                       clock-names = "bi_tcxo",
> > @@ -2558,6 +2746,7 @@ dispcc: clock-controller@af00000 {
> >                       #power-domain-cells = <1>;
> >
> >                       power-domains = <&rpmhpd SM8350_MMCX>;
> > +                     required-opps = <&rpmhpd_opp_turbo>;
> A turbo vote is required for it to function? Seems a bit high..

Dmitry hit a snag using &rpmhpd_opp_low_svs, so this was a dummy
value. I can't replicate that issue, but am having a conversation with
him off-list about this.

On my sm8350-hdk board &rpmhpd_opp_low_svs is working fine.

>
> Konrad
> >               };
> >
> >               adsp: remoteproc@17300000 {
Dmitry Baryshkov Nov. 29, 2022, 7:59 p.m. UTC | #3
On 29/11/2022 18:47, Robert Foss wrote:
> On Tue, 15 Nov 2022 at 14:47, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>
>>
>>
>> On 15/11/2022 14:31, Robert Foss wrote:
>>> Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
>>> nodes the display subsystem is configured to support
>>> one DSI output.
>>>
>>> Signed-off-by: Robert Foss <robert.foss@linaro.org>
>>> ---
>>>    arch/arm64/boot/dts/qcom/sm8350.dtsi | 197 ++++++++++++++++++++++++++-
>>>    1 file changed, 193 insertions(+), 4 deletions(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
>>> index 434f8e8b12c1..5c98e5cf5ad0 100644
>>> --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
>>> +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
>>> @@ -3,6 +3,7 @@
>>>     * Copyright (c) 2020, Linaro Limited
>>>     */
>>>
>>> +#include <dt-bindings/interconnect/qcom,sm8350.h>
>>>    #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>    #include <dt-bindings/clock/qcom,dispcc-sm8350.h>
>>>    #include <dt-bindings/clock/qcom,gcc-sm8350.h>
>>> @@ -2536,14 +2537,201 @@ usb_2_dwc3: usb@a800000 {
>>>                        };
>>>                };
>>>
>>> +             mdss: mdss@ae00000 {
>>> +                     compatible = "qcom,sm8350-mdss";
>>> +                     reg = <0 0x0ae00000 0 0x1000>;
>>> +                     reg-names = "mdss";
>>> +
>>> +                     interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
>>> +                                     <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
>>> +                     interconnect-names = "mdp0-mem", "mdp1-mem";
>>> +
>>> +                     power-domains = <&dispcc MDSS_GDSC>;
>>> +                     resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
>>> +
>>> +                     clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
>>> +                              <&gcc GCC_DISP_HF_AXI_CLK>,
>>> +                              <&gcc GCC_DISP_SF_AXI_CLK>,
>>> +                              <&dispcc DISP_CC_MDSS_MDP_CLK>;
>>> +                     clock-names = "iface", "bus", "nrt_bus", "core";
>>> +
>>> +                     interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
>>> +                     interrupt-controller;
>>> +                     #interrupt-cells = <1>;
>>> +
>>> +                     iommus = <&apps_smmu 0x820 0x402>;
>>> +
>>> +                     status = "disabled";
>>> +
>>> +                     #address-cells = <2>;
>>> +                     #size-cells = <2>;
>>> +                     ranges;
>>> +
>>> +                     mdss_mdp: display-controller@ae01000 {
>>> +                             compatible = "qcom,sm8350-dpu";
>>> +                             reg = <0 0x0ae01000 0 0x8f000>,
>>> +                                   <0 0x0aeb0000 0 0x2008>;
>>> +                             reg-names = "mdp", "vbif";
>>> +
>>> +                             clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
>>> +                                     <&gcc GCC_DISP_SF_AXI_CLK>,
>>> +                                     <&dispcc DISP_CC_MDSS_AHB_CLK>,
>>> +                                     <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
>>> +                                     <&dispcc DISP_CC_MDSS_MDP_CLK>,
>>> +                                     <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
>>> +                             clock-names = "bus",
>>> +                                           "nrt_bus",
>>> +                                           "iface",
>>> +                                           "lut",
>>> +                                           "core",
>>> +                                           "vsync";
>>> +
>>> +                             assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
>>> +                             assigned-clock-rates = <19200000>;
>>> +
>>> +                             operating-points-v2 = <&mdp_opp_table>;
>>> +                             power-domains = <&rpmhpd SM8350_MMCX>;
>>> +
>>> +                             interrupt-parent = <&mdss>;
>>> +                             interrupts = <0>;
>>> +
>>> +                             status = "disabled";
>> It doesn't make sense to disable mdp separately, as mdss is essentially
>> useless without it.
> 
> Ack
> 
>>
>>> +
>>> +                             ports {
>>> +                                     #address-cells = <1>;
>>> +                                     #size-cells = <0>;
>>> +
>>> +                                     port@0 {
>>> +                                             reg = <0>;
>>> +                                             dpu_intf1_out: endpoint {
>>> +                                                     remote-endpoint = <&dsi0_in>;
>>> +                                             };
>>> +                                     };
>>> +                             };
>>> +
>>> +                             mdp_opp_table: opp-table {
>>> +                                     compatible = "operating-points-v2";
>>> +
>>> +                                     opp-200000000 {
>>> +                                             opp-hz = /bits/ 64 <200000000>;
>>> +                                             required-opps = <&rpmhpd_opp_low_svs>;
>>> +                                     };
>>> +
>>> +                                     opp-300000000 {
>>> +                                             opp-hz = /bits/ 64 <300000000>;
>>> +                                             required-opps = <&rpmhpd_opp_svs>;
>>> +                                     };
>>> +
>>> +                                     opp-345000000 {
>>> +                                             opp-hz = /bits/ 64 <345000000>;
>>> +                                             required-opps = <&rpmhpd_opp_svs_l1>;
>>> +                                     };
>>> +
>>> +                                     opp-460000000 {
>>> +                                             opp-hz = /bits/ 64 <460000000>;
>>> +                                             required-opps = <&rpmhpd_opp_nom>;
>>> +                                     };
>>> +                             };
>>> +                     };
>>> +
>>> +                     dsi0: dsi@ae94000 {
>>> +                             compatible = "qcom,mdss-dsi-ctrl";
>>> +                             reg = <0 0x0ae94000 0 0x400>;
>>> +                             reg-names = "dsi_ctrl";
>>> +
>>> +                             interrupt-parent = <&mdss>;
>>> +                             interrupts = <4>;
>>> +
>>> +                             clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
>>> +                                      <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
>>> +                                      <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
>>> +                                      <&dispcc DISP_CC_MDSS_ESC0_CLK>,
>>> +                                      <&dispcc DISP_CC_MDSS_AHB_CLK>,
>>> +                                      <&gcc GCC_DISP_HF_AXI_CLK>;
>>> +                             clock-names = "byte",
>>> +                                           "byte_intf",
>>> +                                           "pixel",
>>> +                                           "core",
>>> +                                           "iface",
>>> +                                           "bus";
>>> +
>>> +                             assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
>>> +                                               <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
>>> +                             assigned-clock-parents = <&dsi0_phy 0>,
>>> +                                                      <&dsi0_phy 1>;
>>> +
>>> +                             operating-points-v2 = <&dsi_opp_table>;
>>> +                             power-domains = <&rpmhpd SM8350_MMCX>;
>>> +
>>> +                             phys = <&dsi0_phy>;
>>> +                             phy-names = "dsi";
>> I think that was dropped as of late.
> 
> Ack
> 
>>
>>> +
>>> +                             status = "disabled";
>>> +
>>> +                             ports {
>>> +                                     #address-cells = <1>;
>>> +                                     #size-cells = <0>;
>>> +
>>> +                                     port@0 {
>>> +                                             reg = <0>;
>>> +                                             dsi0_in: endpoint {
>>> +                                                     remote-endpoint = <&dpu_intf1_out>;
>>> +                                             };
>>> +                                     };
>>> +
>>> +                                     port@1 {
>>> +                                             reg = <1>;
>>> +                                             dsi0_out: endpoint {
>>> +                                             };
>>> +                                     };
>>> +                             };
>>> +                     };
>>> +
>>> +                     dsi0_phy: phy@ae94400 {
>>> +                             compatible = "qcom,dsi-phy-5nm-8350";
>>> +                             reg = <0 0x0ae94400 0 0x200>,
>>> +                                   <0 0x0ae94600 0 0x280>,
>>> +                                   <0 0x0ae94900 0 0x260>;
>>> +                             reg-names = "dsi_phy",
>>> +                                         "dsi_phy_lane",
>>> +                                         "dsi_pll";
>>> +
>>> +                             #clock-cells = <1>;
>>> +                             #phy-cells = <0>;
>>> +
>>> +                             clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
>>> +                                      <&rpmhcc RPMH_CXO_CLK>;
>>> +                             clock-names = "iface", "ref";
>>> +
>>> +                             status = "disabled";
>>> +
>>> +                             dsi_opp_table: dsi-opp-table {
>>> +                                     compatible = "operating-points-v2";
>>> +
>>> +                                     opp-187500000 {
>>> +                                             opp-hz = /bits/ 64 <187500000>;
>>> +                                             required-opps = <&rpmhpd_opp_low_svs>;
>>> +                                     };
>>> +
>>> +                                     opp-300000000 {
>>> +                                             opp-hz = /bits/ 64 <300000000>;
>>> +                                             required-opps = <&rpmhpd_opp_svs>;
>>> +                                     };
>>> +
>>> +                                     opp-358000000 {
>>> +                                             opp-hz = /bits/ 64 <358000000>;
>>> +                                             required-opps = <&rpmhpd_opp_svs_l1>;
>>> +                                     };
>>> +                             };
>>> +                     };
>>> +             };
>>> +
>>>                dispcc: clock-controller@af00000 {
>>>                        compatible = "qcom,sm8350-dispcc";
>>>                        reg = <0 0x0af00000 0 0x10000>;
>>>                        clocks = <&rpmhcc RPMH_CXO_CLK>,
>>> -                              <0>,
>>> -                              <0>,
>>> -                              <0>,
>>> -                              <0>,
>>> +                              <&dsi0_phy 0>, <&dsi0_phy 1>,
>>> +                              <0>, <0>,
>>>                                 <0>,
>>>                                 <0>;
>>>                        clock-names = "bi_tcxo",
>>> @@ -2558,6 +2746,7 @@ dispcc: clock-controller@af00000 {
>>>                        #power-domain-cells = <1>;
>>>
>>>                        power-domains = <&rpmhpd SM8350_MMCX>;
>>> +                     required-opps = <&rpmhpd_opp_turbo>;
>> A turbo vote is required for it to function? Seems a bit high..
> 
> Dmitry hit a snag using &rpmhpd_opp_low_svs, so this was a dummy
> value. I can't replicate that issue, but am having a conversation with
> him off-list about this.
> 
> On my sm8350-hdk board &rpmhpd_opp_low_svs is working fine.

Maybe this is related to the bootloader setting up the mode or maybe it 
was caused by the fact that I have the drm_msm set up as built-in rather 
than a module.

> 
>>
>> Konrad
>>>                };
>>>
>>>                adsp: remoteproc@17300000 {
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 434f8e8b12c1..5c98e5cf5ad0 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -3,6 +3,7 @@ 
  * Copyright (c) 2020, Linaro Limited
  */
 
+#include <dt-bindings/interconnect/qcom,sm8350.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,dispcc-sm8350.h>
 #include <dt-bindings/clock/qcom,gcc-sm8350.h>
@@ -2536,14 +2537,201 @@  usb_2_dwc3: usb@a800000 {
 			};
 		};
 
+		mdss: mdss@ae00000 {
+			compatible = "qcom,sm8350-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
+					<&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "mdp0-mem", "mdp1-mem";
+
+			power-domains = <&dispcc MDSS_GDSC>;
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&gcc GCC_DISP_SF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+			clock-names = "iface", "bus", "nrt_bus", "core";
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			iommus = <&apps_smmu 0x820 0x402>;
+
+			status = "disabled";
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			mdss_mdp: display-controller@ae01000 {
+				compatible = "qcom,sm8350-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+					<&gcc GCC_DISP_SF_AXI_CLK>,
+					<&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_CLK>,
+					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "bus",
+					      "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
+
+				operating-points-v2 = <&mdp_opp_table>;
+				power-domains = <&rpmhpd SM8350_MMCX>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+				};
+
+				mdp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-345000000 {
+						opp-hz = /bits/ 64 <345000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-460000000 {
+						opp-hz = /bits/ 64 <460000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			dsi0: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&dsi0_phy 0>,
+							 <&dsi0_phy 1>;
+
+				operating-points-v2 = <&dsi_opp_table>;
+				power-domains = <&rpmhpd SM8350_MMCX>;
+
+				phys = <&dsi0_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi0_phy: phy@ae94400 {
+				compatible = "qcom,dsi-phy-5nm-8350";
+				reg = <0 0x0ae94400 0 0x200>,
+				      <0 0x0ae94600 0 0x280>,
+				      <0 0x0ae94900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+
+				dsi_opp_table: dsi-opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+			};
+		};
+
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sm8350-dispcc";
 			reg = <0 0x0af00000 0 0x10000>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
+				 <&dsi0_phy 0>, <&dsi0_phy 1>,
+				 <0>, <0>,
 				 <0>,
 				 <0>;
 			clock-names = "bi_tcxo",
@@ -2558,6 +2746,7 @@  dispcc: clock-controller@af00000 {
 			#power-domain-cells = <1>;
 
 			power-domains = <&rpmhpd SM8350_MMCX>;
+			required-opps = <&rpmhpd_opp_turbo>;
 		};
 
 		adsp: remoteproc@17300000 {