| Message ID | 20221119203758.888207-4-luca@z3ntu.xyz (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add a bunch of msm8953 dts files | expand |
On 19.11.2022 21:37, Luca Weiss wrote: > From: Julian Braha <julianbraha@gmail.com> > > Add device tree for the Motorola Moto G6 (ali) smartphone. This device > is based on Snapdragon 450 (sdm450) SoC which is a variant of MSM8953. > > Signed-off-by: Julian Braha <julianbraha@gmail.com> > Signed-off-by: Luca Weiss <luca@z3ntu.xyz> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> > Changes in v2: > * address review comments from v1 Veeeeeeery vauge! Konrad > > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/sdm450-motorola-ali.dts | 250 ++++++++++++++++++ > 2 files changed, 251 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/sdm450-motorola-ali.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index afe496a93f94..6bc1be0d525a 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -120,6 +120,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb > dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb > dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb > dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb > +dtb-$(CONFIG_ARCH_QCOM) += sdm450-motorola-ali.dtb > dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-ganges-kirin.dtb > dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-discovery.dtb > dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-pioneer.dtb > diff --git a/arch/arm64/boot/dts/qcom/sdm450-motorola-ali.dts b/arch/arm64/boot/dts/qcom/sdm450-motorola-ali.dts > new file mode 100644 > index 000000000000..43e2941f98d9 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sdm450-motorola-ali.dts > @@ -0,0 +1,250 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2022, Julian Braha <julianbraha@gmail.com> > + */ > +/dts-v1/; > + > +#include "msm8953.dtsi" > +#include "pm8953.dtsi" > +#include "pmi8950.dtsi" > + > +/delete-node/ &qseecom_mem; > + > +/ { > + model = "Motorola Moto G6"; > + compatible = "motorola,ali", "qcom,sdm450"; > + chassis-type = "handset"; > + qcom,msm-id = <338 0>; > + qcom,board-id = <0x43 0xc200>; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + key-volume-up { > + label = "volume_up"; > + gpios = <&tlmm 85 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + }; > + > + reserved-memory { > + qseecom_mem: qseecom@84300000 { > + reg = <0x0 0x84300000 0x0 0x2000000>; > + no-map; > + }; > + > + ramoops@ef000000 { > + compatible = "ramoops"; > + reg = <0x0 0xef000000 0x0 0xc0000>; > + console-size = <0x40000>; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-always-on; > + regulator-boot-on; > + }; > +}; > + > +&hsusb_phy { > + vdd-supply = <&pm8953_l3>; > + vdda-pll-supply = <&pm8953_l7>; > + vdda-phy-dpdm-supply = <&pm8953_l13>; > + > + status = "okay"; > +}; > + > +&i2c_3 { > + status = "okay"; > + > + touchscreen@38 { > + compatible = "edt,edt-ft5406"; > + reg = <0x38>; > + interrupt-parent = <&tlmm>; > + interrupts = <65 IRQ_TYPE_EDGE_FALLING>; > + vcc-supply = <&pm8953_l10>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&ts_int_active &ts_reset_active>; > + > + reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>; > + touchscreen-size-x = <1080>; > + touchscreen-size-y = <2160>; > + }; > +}; > + > +&pm8953_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + status = "okay"; > +}; > + > +&pmi8950_wled { > + qcom,num-strings = <3>; > + qcom,external-pfet; > + qcom,cabc; > + > + status = "okay"; > +}; > + > +&rpm_requests { > + regulators { > + compatible = "qcom,rpm-pm8953-regulators"; > + > + vdd_s1-supply = <&vph_pwr>; > + vdd_s2-supply = <&vph_pwr>; > + vdd_s3-supply = <&vph_pwr>; > + vdd_s4-supply = <&vph_pwr>; > + vdd_s5-supply = <&vph_pwr>; > + vdd_s6-supply = <&vph_pwr>; > + vdd_s7-supply = <&vph_pwr>; > + vdd_l1-supply = <&pm8953_s3>; > + vdd_l2_l3-supply = <&pm8953_s3>; > + vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>; > + vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>; > + vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>; > + > + pm8953_s1: s1 { > + regulator-min-microvolt = <795000>; > + regulator-max-microvolt = <1081000>; > + }; > + > + pm8953_s3: s3 { > + regulator-min-microvolt = <1224000>; > + regulator-max-microvolt = <1224000>; > + }; > + > + pm8953_s4: s4 { > + regulator-min-microvolt = <1900000>; > + regulator-max-microvolt = <2050000>; > + }; > + > + pm8953_l1: l1 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1100000>; > + }; > + > + pm8953_l2: l2 { > + regulator-min-microvolt = <975000>; > + regulator-max-microvolt = <1225000>; > + }; > + > + pm8953_l3: l3 { > + regulator-min-microvolt = <925000>; > + regulator-max-microvolt = <925000>; > + }; > + > + pm8953_l5: l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + pm8953_l6: l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + pm8953_l7: l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1900000>; > + }; > + > + pm8953_l8: l8 { > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + }; > + > + pm8953_l9: l9 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + pm8953_l10: l10 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + pm8953_l11: l11 { > + regulator-min-microvolt = <2950000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + pm8953_l12: l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + pm8953_l13: l13 { > + regulator-min-microvolt = <3125000>; > + regulator-max-microvolt = <3125000>; > + }; > + > + pm8953_l16: l16 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + pm8953_l17: l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + pm8953_l19: l19 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1350000>; > + }; > + > + pm8953_l22: l22 { > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + pm8953_l23: l23 { > + regulator-min-microvolt = <975000>; > + regulator-max-microvolt = <1225000>; > + }; > + }; > +}; > + > +&sdhc_1 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>; > + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>; > + > + status = "okay"; > +}; > + > +&sdhc_2 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_off>; > + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; > + > + status = "okay"; > +}; > + > +&tlmm { > + gpio-reserved-ranges = <95 5>, <111 1>, <126 1>; > + > + ts_int_active: ts-int-active-state { > + pins = "gpio65"; > + function = "gpio"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + ts_reset_active: ts-reset-active-state { > + pins = "gpio64"; > + function = "gpio"; > + drive-strength = <0x08>; > + bias-pull-up; > + }; > +}; > + > +&usb3 { > + status = "okay"; > +}; > + > +&usb3_dwc3 { > + dr_mode = "peripheral"; > +};
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index afe496a93f94..6bc1be0d525a 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -120,6 +120,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm450-motorola-ali.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-ganges-kirin.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-discovery.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-pioneer.dtb diff --git a/arch/arm64/boot/dts/qcom/sdm450-motorola-ali.dts b/arch/arm64/boot/dts/qcom/sdm450-motorola-ali.dts new file mode 100644 index 000000000000..43e2941f98d9 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm450-motorola-ali.dts @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2022, Julian Braha <julianbraha@gmail.com> + */ +/dts-v1/; + +#include "msm8953.dtsi" +#include "pm8953.dtsi" +#include "pmi8950.dtsi" + +/delete-node/ &qseecom_mem; + +/ { + model = "Motorola Moto G6"; + compatible = "motorola,ali", "qcom,sdm450"; + chassis-type = "handset"; + qcom,msm-id = <338 0>; + qcom,board-id = <0x43 0xc200>; + + gpio-keys { + compatible = "gpio-keys"; + + key-volume-up { + label = "volume_up"; + gpios = <&tlmm 85 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + reserved-memory { + qseecom_mem: qseecom@84300000 { + reg = <0x0 0x84300000 0x0 0x2000000>; + no-map; + }; + + ramoops@ef000000 { + compatible = "ramoops"; + reg = <0x0 0xef000000 0x0 0xc0000>; + console-size = <0x40000>; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + }; +}; + +&hsusb_phy { + vdd-supply = <&pm8953_l3>; + vdda-pll-supply = <&pm8953_l7>; + vdda-phy-dpdm-supply = <&pm8953_l13>; + + status = "okay"; +}; + +&i2c_3 { + status = "okay"; + + touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + interrupt-parent = <&tlmm>; + interrupts = <65 IRQ_TYPE_EDGE_FALLING>; + vcc-supply = <&pm8953_l10>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_active &ts_reset_active>; + + reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <1080>; + touchscreen-size-y = <2160>; + }; +}; + +&pm8953_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&pmi8950_wled { + qcom,num-strings = <3>; + qcom,external-pfet; + qcom,cabc; + + status = "okay"; +}; + +&rpm_requests { + regulators { + compatible = "qcom,rpm-pm8953-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_l1-supply = <&pm8953_s3>; + vdd_l2_l3-supply = <&pm8953_s3>; + vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>; + vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>; + vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>; + + pm8953_s1: s1 { + regulator-min-microvolt = <795000>; + regulator-max-microvolt = <1081000>; + }; + + pm8953_s3: s3 { + regulator-min-microvolt = <1224000>; + regulator-max-microvolt = <1224000>; + }; + + pm8953_s4: s4 { + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <2050000>; + }; + + pm8953_l1: l1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + }; + + pm8953_l2: l2 { + regulator-min-microvolt = <975000>; + regulator-max-microvolt = <1225000>; + }; + + pm8953_l3: l3 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <925000>; + }; + + pm8953_l5: l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8953_l6: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8953_l7: l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1900000>; + }; + + pm8953_l8: l8 { + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + }; + + pm8953_l9: l9 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + }; + + pm8953_l10: l10 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + pm8953_l11: l11 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + }; + + pm8953_l12: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + pm8953_l13: l13 { + regulator-min-microvolt = <3125000>; + regulator-max-microvolt = <3125000>; + }; + + pm8953_l16: l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8953_l17: l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + pm8953_l19: l19 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1350000>; + }; + + pm8953_l22: l22 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2850000>; + }; + + pm8953_l23: l23 { + regulator-min-microvolt = <975000>; + regulator-max-microvolt = <1225000>; + }; + }; +}; + +&sdhc_1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>; + + status = "okay"; +}; + +&sdhc_2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_off>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <95 5>, <111 1>, <126 1>; + + ts_int_active: ts-int-active-state { + pins = "gpio65"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + ts_reset_active: ts-reset-active-state { + pins = "gpio64"; + function = "gpio"; + drive-strength = <0x08>; + bias-pull-up; + }; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_dwc3 { + dr_mode = "peripheral"; +};