@@ -82,81 +82,74 @@ properties:
Phandle to TCSR syscon register region.
$ref: /schemas/types.yaml#/definitions/phandle
-if:
- properties:
- compatible:
- contains:
- const: qcom,qusb2-v2-phy
-then:
- properties:
- qcom,imp-res-offset-value:
- description:
- It is a 6 bit value that specifies offset to be
- added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
- tuning parameter that may vary for different boards of same SOC.
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 0
- maximum: 63
- default: 0
-
- qcom,bias-ctrl-value:
- description:
- It is a 6 bit value that specifies bias-ctrl-value. It is a PHY
- tuning parameter that may vary for different boards of same SOC.
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 0
- maximum: 63
- default: 32
-
- qcom,charge-ctrl-value:
- description:
- It is a 2 bit value that specifies charge-ctrl-value. It is a PHY
- tuning parameter that may vary for different boards of same SOC.
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 0
- maximum: 3
- default: 0
-
- qcom,hstx-trim-value:
- description:
- It is a 4 bit value that specifies tuning for HSTX
- output current.
- Possible range is - 15mA to 24mA (stepsize of 600 uA).
- See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 0
- maximum: 15
- default: 3
-
- qcom,preemphasis-level:
- description:
- It is a 2 bit value that specifies pre-emphasis level.
- Possible range is 0 to 15% (stepsize of 5%).
- See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 0
- maximum: 3
- default: 2
-
- qcom,preemphasis-width:
- description:
- It is a 1 bit value that specifies how long the HSTX
- pre-emphasis (specified using qcom,preemphasis-level) must be in
- effect. Duration could be half-bit of full-bit.
- See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 0
- maximum: 1
- default: 0
-
- qcom,hsdisc-trim-value:
- description:
- It is a 2 bit value tuning parameter that control disconnect
- threshold and may vary for different boards of same SOC.
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 0
- maximum: 3
- default: 0
+ qcom,imp-res-offset-value:
+ description:
+ It is a 6 bit value that specifies offset to be
+ added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
+ tuning parameter that may vary for different boards of same SOC.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 63
+ default: 0
+
+ qcom,bias-ctrl-value:
+ description:
+ It is a 6 bit value that specifies bias-ctrl-value. It is a PHY
+ tuning parameter that may vary for different boards of same SOC.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 63
+ default: 32
+
+ qcom,charge-ctrl-value:
+ description:
+ It is a 2 bit value that specifies charge-ctrl-value. It is a PHY
+ tuning parameter that may vary for different boards of same SOC.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 0
+
+ qcom,hstx-trim-value:
+ description:
+ It is a 4 bit value that specifies tuning for HSTX
+ output current.
+ Possible range is - 15mA to 24mA (stepsize of 600 uA).
+ See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ default: 3
+
+ qcom,preemphasis-level:
+ description:
+ It is a 2 bit value that specifies pre-emphasis level.
+ Possible range is 0 to 15% (stepsize of 5%).
+ See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 2
+
+ qcom,preemphasis-width:
+ description:
+ It is a 1 bit value that specifies how long the HSTX
+ pre-emphasis (specified using qcom,preemphasis-level) must be in
+ effect. Duration could be half-bit of full-bit.
+ See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 1
+ default: 0
+
+ qcom,hsdisc-trim-value:
+ description:
+ It is a 2 bit value tuning parameter that control disconnect
+ threshold and may vary for different boards of same SOC.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 0
required:
- compatible
@@ -169,6 +162,23 @@ required:
- vdda-phy-dpdm-supply
- resets
+allOf:
+ - if:
+ not:
+ properties:
+ compatible:
+ contains:
+ const: qcom,qusb2-v2-phy
+ then:
+ properties:
+ qcom,imp-res-offset-value: false
+ qcom,bias-ctrl-value: false
+ qcom,charge-ctrl-value: false
+ qcom,hstx-trim-value: false
+ qcom,preemphasis-level: false
+ qcom,preemphasis-width: false
+ qcom,hsdisc-trim-value: false
+
additionalProperties: false
examples:
It is more readable to define properties in top-level "properties:" and restrict them (if needed) per compatible in the "if" block. Defining properties in "if" block does not work correctly with additionalProperties:false: sc7180-trogdor-pazquel-lte-ti.dtb: phy@88e3000: 'qcom,bias-ctrl-value', 'qcom,charge-ctrl-value', 'qcom,hsdisc-trim-value', 'qcom,imp-res-offset-value', 'qcom,preemphasis-level', 'qcom,preemphasis-width' do not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- .../bindings/phy/qcom,qusb2-phy.yaml | 160 ++++++++++-------- 1 file changed, 85 insertions(+), 75 deletions(-)