@@ -201,8 +201,8 @@ crypto: crypto@73a000 {
compatible = "qcom,crypto-v5.1";
reg = <0x0 0x0073a000 0x0 0x6000>;
clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
- <&gcc GCC_CRYPTO_AXI_CLK>,
- <&gcc GCC_CRYPTO_CLK>;
+ <&gcc GCC_CRYPTO_AXI_CLK>,
+ <&gcc GCC_CRYPTO_CLK>;
clock-names = "iface", "bus", "core";
dmas = <&cryptobam 2>, <&cryptobam 3>;
dma-names = "rx", "tx";
@@ -272,7 +272,7 @@ blsp1_uart3: serial@78b1000 {
reg = <0x0 0x078b1000 0x0 0x200>;
interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
- <&gcc GCC_BLSP1_AHB_CLK>;
+ <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
@@ -285,7 +285,7 @@ blsp1_spi1: spi@78b5000 {
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
spi-max-frequency = <50000000>;
clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
- <&gcc GCC_BLSP1_AHB_CLK>;
+ <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
dmas = <&blsp_dma 12>, <&blsp_dma 13>;
dma-names = "tx", "rx";
@@ -300,7 +300,7 @@ blsp1_spi2: spi@78b6000 {
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
spi-max-frequency = <50000000>;
clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
- <&gcc GCC_BLSP1_AHB_CLK>;
+ <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
dmas = <&blsp_dma 14>, <&blsp_dma 15>;
dma-names = "tx", "rx";
@@ -358,8 +358,8 @@ qpic_nand: nand-controller@79b0000 {
clock-names = "core", "aon";
dmas = <&qpic_bam 0>,
- <&qpic_bam 1>,
- <&qpic_bam 2>;
+ <&qpic_bam 1>,
+ <&qpic_bam 2>;
dma-names = "tx", "rx", "cmd";
pinctrl-0 = <&qpic_pins>;
pinctrl-names = "default";
@@ -372,10 +372,10 @@ intc: interrupt-controller@b000000 {
#size-cells = <2>;
interrupt-controller;
#interrupt-cells = <0x3>;
- reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/
- <0x0 0x0b002000 0x0 0x1000>, /*GICC*/
- <0x0 0x0b001000 0x0 0x1000>, /*GICH*/
- <0x0 0x0b004000 0x0 0x1000>; /*GICV*/
+ reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/
+ <0x0 0x0b002000 0x0 0x1000>, /*GICC*/
+ <0x0 0x0b001000 0x0 0x1000>, /*GICH*/
+ <0x0 0x0b004000 0x0 0x1000>; /*GICV*/
interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
ranges = <0 0 0 0xb00a000 0 0xffd>;
@@ -663,17 +663,17 @@ usb2: usb@70f8800 {
status = "disabled";
dwc_1: usb@7000000 {
- compatible = "snps,dwc3";
- reg = <0x0 0x07000000 0x0 0xcd00>;
- interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&qusb_phy_1>;
- phy-names = "usb2-phy";
- tx-fifo-resize;
- snps,is-utmi-l1-suspend;
- snps,hird-threshold = /bits/ 8 <0x0>;
- snps,dis_u2_susphy_quirk;
- snps,dis_u3_susphy_quirk;
- dr_mode = "host";
+ compatible = "snps,dwc3";
+ reg = <0x0 0x07000000 0x0 0xcd00>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&qusb_phy_1>;
+ phy-names = "usb2-phy";
+ tx-fifo-resize;
+ snps,is-utmi-l1-suspend;
+ snps,hird-threshold = /bits/ 8 <0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ dr_mode = "host";
};
};
The dwc3 subnode was indented using spaces for some reason and other properties were not exactly properly indented. Fix it. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- v1 -> v2: - Squash with a similar indent-fixing patch [4/18] arch/arm64/boot/dts/qcom/ipq6018.dtsi | 44 +++++++++++++-------------- 1 file changed, 22 insertions(+), 22 deletions(-)