| Message ID | 20230125112903.10710-2-lujianhua000@gmail.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v2,1/2] dt-bindings: arm: qcom: Add Xiaomi Mi Pad 5 Pro (xiaomi-elish) | expand |
On 25.01.2023 12:29, Jianhua Lu wrote: > Add support for Xiaomi Mi Pad 5 Pro, codename is xiaomi-elish. > > This commit brings support for: > * ADSP/CDSP/SLPI/VENUS > * Backlight > * Battery fuel gauge > * Framebuffer > * PCIe0 > * USB2.0 > > Note backlight driver (ktz8866) is waitting for upstreaming[1]. > [1] https://lore.kernel.org/linux-leds/20230120155018.15376-1-lujianhua000@gmail.com This should be placed below --- (next to where you pu Changes in v2) so that it's not included in the final commit message when Bjorn picks it up. > > Signed-off-by: Jianhua Lu <lujianhua000@gmail.com> > --- > Changes in v2: > - Apply Konrad's and Krzysztof's suggestion. This should generally be more verbose.. > > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/sm8250-xiaomi-elish.dts | 617 ++++++++++++++++++ > 2 files changed, 618 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index b0423ca3e79f..769cee2b450f 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -184,6 +184,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8250-hdk.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx203.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx206.dtb > +dtb-$(CONFIG_ARCH_QCOM) += sm8250-xiaomi-elish.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8350-hdk.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8350-microsoft-surface-duo2.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb > diff --git a/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts b/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts > new file mode 100644 > index 000000000000..f352b80b0ced > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts > @@ -0,0 +1,617 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2022, 2023 Jianhua Lu <lujianhua000@gmail.com> > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/arm/qcom,ids.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include "sm8250.dtsi" > +#include "pm8150.dtsi" > +#include "pm8150b.dtsi" > +#include "pm8150l.dtsi" > +#include "pm8009.dtsi" > + > +/* > + * Delete following upstream (sm8250.dtsi) reserved > + * memory mappings which are different in this device. on this device* > + */ > +/delete-node/ &xbl_aop_mem; > +/delete-node/ &slpi_mem; > +/delete-node/ &adsp_mem; > +/delete-node/ &spss_mem; > +/delete-node/ &cdsp_secure_heap; Could you please sort these alphabetically? > + > +/ { > + model = "Xiaomi Mi Pad 5 Pro"; > + compatible = "xiaomi,elish", "qcom,sm8250"; > + classis-type = "tablet"; > + > + /* required for bootloader to select correct board */ > + qcom,msm-id = <QCOM_ID_SM8250 0x20001>; /* SM8250 v2.1 */ > + qcom,board-id = <0x10008 0>; > + > + chosen { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + framebuffer: framebuffer@9c000000 { > + compatible = "simple-framebuffer"; > + reg = <0x0 0x9c000000 0x0 0x2300000>; > + width = <1600>; > + height = <2560>; > + stride = <(1600 * 4)>; > + format = "a8r8g8b8"; > + }; > + }; > + > + battery_l: battery-l { > + compatible = "simple-battery"; > + voltage-min-design-microvolt = <3870000>; > + energy-full-design-microwatt-hours = <16600000>; > + charge-full-design-microamp-hours = <4300000>; > + }; > + > + battery_r: battery-r { > + compatible = "simple-battery"; > + voltage-min-design-microvolt = <3870000>; > + energy-full-design-microwatt-hours = <16600000>; > + charge-full-design-microamp-hours = <4300000>; > + }; > + > + bl_vddpos_5p5: bl-vddpos-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "bl_vddpos_5p5"; > + regulator-min-microvolt = <5500000>; > + regulator-max-microvolt = <5500000>; > + regulator-enable-ramp-delay = <233>; > + gpio = <&tlmm 130 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-boot-on; > + }; > + > + bl_vddneg_5p5: bl-vddneg-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "bl_vddneg_5p5"; > + regulator-min-microvolt = <5500000>; > + regulator-max-microvolt = <5500000>; > + regulator-enable-ramp-delay = <233>; > + gpio = <&tlmm 131 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-boot-on; > + }; > + > + gpio_keys: gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-name = "default"; > + pinctrl-0 = <&vol_up_n>; > + > + key-vol-up { > + label = "Volume Up"; > + gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + debounce-interval = <15>; > + linux,can-disable; > + gpio-key,wakeup; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + }; > + > + /* S6c is really ebi.lvl but it's there for supply map completeness sake. */ > + vreg_s6c_0p88: smpc6-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vreg_s6c_0p88"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <880000>; > + regulator-always-on; > + vin-supply = <&vph_pwr>; > + }; > + > + reserved-memory { > + xbl_aop_mem: memory@80700000 { Forgot about this earlier, but should be something-descriptive@ instead of memory@, so for example here: xbl_aop_mem: xbl-aop@ The rest LGTM, I think! Konrad > + reg = <0x0 0x80600000 0x0 0x260000>; > + no-map; > + }; > + > + slpi_mem: memory@88c00000 { > + reg = <0x0 0x88c00000 0x0 0x2f00000>; > + no-map; > + }; > + > + adsp_mem: memory@8bb00000 { > + reg = <0x0 0x8bb00000 0x0 0x2500000>; > + no-map; > + }; > + > + spss_mem: memory@8e000000 { > + reg = <0x0 0x8e000000 0x0 0x100000>; > + no-map; > + }; > + > + cdsp_secure_heap: memory@8e100000 { > + reg = <0x0 0x8e100000 0x0 0x4600000>; > + no-map; > + }; > + > + cont_splash_mem: memory@9c000000 { > + reg = <0x0 0x9c000000 0x0 0x2300000>; > + no-map; > + }; > + > + ramoops@b0000000 { > + compatible = "ramoops"; > + reg = <0x0 0xb0000000 0x0 0x400000>; > + record-size = <0x1000>; > + console-size = <0x200000>; > + ecc-size = <16>; > + no-map; > + }; > + }; > +}; > + > +&adsp { > + firmware-name = "qcom/sm8250/xiaomi/elish/adsp.mbn"; > + status = "okay"; > +}; > + > +&apps_rsc { > + regulators-0 { > + compatible = "qcom,pm8150-rpmh-regulators"; > + qcom,pmic-id = "a"; > + > + vdd-s1-supply = <&vph_pwr>; > + vdd-s2-supply = <&vph_pwr>; > + vdd-s3-supply = <&vph_pwr>; > + vdd-s4-supply = <&vph_pwr>; > + vdd-s5-supply = <&vph_pwr>; > + vdd-s6-supply = <&vph_pwr>; > + vdd-s7-supply = <&vph_pwr>; > + vdd-s8-supply = <&vph_pwr>; > + vdd-s9-supply = <&vph_pwr>; > + vdd-s10-supply = <&vph_pwr>; > + vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>; > + vdd-l2-l10-supply = <&vreg_bob>; > + vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>; > + vdd-l6-l9-supply = <&vreg_s8c_1p35>; > + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; > + vdd-l13-l16-l17-supply = <&vreg_bob>; > + > + /* (S1+S2+S3) - cx.lvl (ARC) */ > + > + vreg_s4a_1p8: smps4 { > + regulator-name = "vreg_s4a_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1920000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s5a_1p9: smps5 { > + regulator-name = "vreg_s5a_1p9"; > + regulator-min-microvolt = <1900000>; > + regulator-max-microvolt = <2040000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s6a_0p95: smps6 { > + regulator-name = "vreg_s6a_0p95"; > + regulator-min-microvolt = <950000>; > + regulator-max-microvolt = <1128000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2a_3p1: ldo2 { > + regulator-name = "vreg_l2a_3p1"; > + regulator-min-microvolt = <3072000>; > + regulator-max-microvolt = <3072000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3a_0p9: ldo3 { > + regulator-name = "vreg_l3a_0p9"; > + regulator-min-microvolt = <928000>; > + regulator-max-microvolt = <932000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L4 - lmx.lvl (ARC) */ > + > + vreg_l5a_0p88: ldo5 { > + regulator-name = "vreg_l5a_0p88"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <880000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6a_1p2: ldo6 { > + regulator-name = "vreg_l6a_1p2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L7 is unused. */ > + > + vreg_l9a_1p2: ldo9 { > + regulator-name = "vreg_l9a_1p2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L10 is unused, L11 - lcx.lvl (ARC) */ > + > + vreg_l12a_1p8: ldo12 { > + regulator-name = "vreg_l12a_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L13 is unused. */ > + > + vreg_l14a_1p88: ldo14 { > + regulator-name = "vreg_l14a_1p88"; > + regulator-min-microvolt = <1880000>; > + regulator-max-microvolt = <1880000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L15 & L16 are unused. */ > + > + vreg_l17a_3p0: ldo17 { > + regulator-name = "vreg_l17a_3p0"; > + regulator-min-microvolt = <2496000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l18a_0p9: ldo18 { > + regulator-name = "vreg_l18a_0p9"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <920000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + /* > + * Remaining regulators that are not yet supported: > + * OLEDB: 4925000-8100000 > + * ab: 4600000-6100000 > + * ibb: 800000-5400000 > + */ > + regulators-1 { > + compatible = "qcom,pm8150l-rpmh-regulators"; > + qcom,pmic-id = "c"; > + > + vdd-s1-supply = <&vph_pwr>; > + vdd-s2-supply = <&vph_pwr>; > + vdd-s3-supply = <&vph_pwr>; > + vdd-s4-supply = <&vph_pwr>; > + vdd-s5-supply = <&vph_pwr>; > + vdd-s6-supply = <&vph_pwr>; > + vdd-s7-supply = <&vph_pwr>; > + vdd-s8-supply = <&vph_pwr>; > + vdd-l1-l8-supply = <&vreg_s4a_1p8>; > + vdd-l2-l3-supply = <&vreg_s8c_1p35>; > + vdd-l4-l5-l6-supply = <&vreg_bob>; > + vdd-l7-l11-supply = <&vreg_bob>; > + vdd-l9-l10-supply = <&vreg_bob>; > + vdd-bob-supply = <&vph_pwr>; > + > + vreg_bob: bob { > + regulator-name = "vreg_bob"; > + regulator-min-microvolt = <3350000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; > + }; > + > + /* > + * S1-S6 are ARCs: > + * (S1+S2) - gfx.lvl, > + * S3 - mx.lvl, > + * (S4+S5) - mmcx.lvl, > + * S6 - ebi.lvl > + */ > + > + vreg_s7c_0p35: smps7 { > + regulator-name = "vreg_s7c_0p35"; > + regulator-min-microvolt = <348000>; > + regulator-max-microvolt = <1000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s8c_1p35: smps8 { > + regulator-name = "vreg_s8c_1p35"; > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <1400000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1c_1p8: ldo1 { > + regulator-name = "vreg_l1c_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L2-4 are unused. */ > + > + vreg_l5c_1p8: ldo5 { > + regulator-name = "vreg_l5c_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6c_2p9: ldo6 { > + regulator-name = "vreg_l6c_2p9"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7c_2p85: ldo7 { > + regulator-name = "vreg_l7c_2p85"; > + regulator-min-microvolt = <2856000>; > + regulator-max-microvolt = <3104000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l8c_1p8: ldo8 { > + regulator-name = "vreg_l8c_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9c_2p9: ldo9 { > + regulator-name = "vreg_l9c_2p9"; > + regulator-min-microvolt = <2704000>; > + regulator-max-microvolt = <2960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10c_3p3: ldo10 { > + regulator-name = "vreg_l10c_3p3"; > + regulator-min-microvolt = <3296000>; > + regulator-max-microvolt = <3296000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11c_3p0: ldo11 { > + regulator-name = "vreg_l11c_3p0"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-2 { > + compatible = "qcom,pm8009-rpmh-regulators"; > + qcom,pmic-id = "f"; > + > + vdd-s1-supply = <&vph_pwr>; > + vdd-s2-supply = <&vreg_bob>; > + vdd-l2-supply = <&vreg_s8c_1p35>; > + vdd-l5-l6-supply = <&vreg_bob>; > + vdd-l7-supply = <&vreg_s4a_1p8>; > + > + vreg_s1f_1p2: smps1 { > + regulator-name = "vreg_s1f_1p2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s2f_0p5: smps2 { > + regulator-name = "vreg_s2f_0p5"; > + regulator-min-microvolt = <512000>; > + regulator-max-microvolt = <1100000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L1 is unused. */ > + > + vreg_l2f_1p3: ldo2 { > + regulator-name = "vreg_l2f_1p3"; > + regulator-min-microvolt = <1304000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L3 & L4 are unused. */ > + > + vreg_l5f_2p8: ldo5 { > + regulator-name = "vreg_l5f_2p85"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6f_2p8: ldo6 { > + regulator-name = "vreg_l6f_2p8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7f_1p8: ldo7 { > + regulator-name = "vreg_l7f_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > +}; > + > +&cdsp { > + firmware-name = "qcom/sm8250/xiaomi/elish/cdsp.mbn"; > + status = "okay"; > +}; > + > +&gpi_dma0 { > + status = "okay"; > +}; > + > +&gpi_dma1 { > + status = "okay"; > +}; > + > +&gpi_dma2 { > + status = "okay"; > +}; > + > +&i2c0 { > + clock-frequency = <400000>; > + status = "okay"; > + > + fuel-gauge@55 { > + compatible = "ti,bq27z561"; > + reg = <0x55>; > + monitored-battery = <&battery_r>; > + }; > +}; > + > +&i2c11 { > + clock-frequency = <400000>; > + status = "okay"; > + > + backlight: backlight@11 { > + compatible = "kinetic,ktz8866"; > + reg = <0x11>; > + vddpos-supply = <&bl_vddpos_5p5>; > + vddneg-supply = <&bl_vddneg_5p5>; > + enable-gpios = <&tlmm 139 GPIO_ACTIVE_HIGH>; > + current-num-sinks = <5>; > + kinetic,current-ramp-delay-ms = <128>; > + kinetic,led-enable-ramp-delay-ms = <1>; > + kinetic,enable-lcd-bias; > + }; > +}; > + > +&i2c13 { > + clock-frequency = <400000>; > + status = "okay"; > + > + fuel-gauge@55 { > + compatible = "ti,bq27z561"; > + reg = <0x55>; > + monitored-battery = <&battery_l>; > + }; > +}; > + > +&pcie0 { > + status = "okay"; > +}; > + > +&pcie0_phy { > + vdda-phy-supply = <&vreg_l5a_0p88>; > + vdda-pll-supply = <&vreg_l9a_1p2>; > + status = "okay"; > +}; > + > +&pm8150_gpios { > + vol_up_n: vol-up-n-state { > + pins = "gpio6"; > + function = "normal"; > + power-source = <1>; > + input-enable; > + bias-pull-up; > + }; > +}; > + > +&pon_pwrkey { > + status = "okay"; > +}; > + > +&pon_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + status = "okay"; > +}; > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&qupv3_id_1 { > + status = "okay"; > +}; > + > +&qupv3_id_2 { > + status = "okay"; > +}; > + > +&slpi { > + firmware-name = "qcom/sm8250/xiaomi/elish/slpi.mbn"; > + status = "okay"; > +}; > + > +&tlmm { > + gpio-reserved-ranges = <40 4>; > +}; > + > +&usb_1 { > + /* USB 2.0 only */ > + qcom,select-utmi-as-pipe-clk; > + status = "okay"; > +}; > + > +&usb_1_dwc3 { > + dr_mode = "peripheral"; > + maximum-spped = "high-speed"; > + /* Remove USB3 phy */ > + phys = <&usb_1_hsphy>; > + phy-names = "usb2-phy"; > +}; > + > +&usb_1_hsphy { > + vdda-pll-supply = <&vreg_l5a_0p88>; > + vdda18-supply = <&vreg_l12a_1p8>; > + vdda33-supply = <&vreg_l2a_3p1>; > + status = "okay"; > +}; > + > +&ufs_mem_hc { > + vcc-supply = <&vreg_l17a_3p0>; > + vcc-max-microamp = <800000>; > + vccq-supply = <&vreg_l6a_1p2>; > + vccq-max-microamp = <800000>; > + vccq2-supply = <&vreg_s4a_1p8>; > + vccq2-max-microamp = <800000>; > + status = "okay"; > +}; > + > +&ufs_mem_phy { > + vdda-phy-supply = <&vreg_l5a_0p88>; > + vdda-pll-supply = <&vreg_l9a_1p2>; > + status = "okay"; > +}; > + > +&venus { > + firmware-name = "qcom/sm8250/elish/venus.mbn"; > + status = "okay"; > +};
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index b0423ca3e79f..769cee2b450f 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -184,6 +184,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8250-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx203.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx206.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8250-xiaomi-elish.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8350-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8350-microsoft-surface-duo2.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts b/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts new file mode 100644 index 000000000000..f352b80b0ced --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts @@ -0,0 +1,617 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2022, 2023 Jianhua Lu <lujianhua000@gmail.com> + */ + +/dts-v1/; + +#include <dt-bindings/arm/qcom,ids.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sm8250.dtsi" +#include "pm8150.dtsi" +#include "pm8150b.dtsi" +#include "pm8150l.dtsi" +#include "pm8009.dtsi" + +/* + * Delete following upstream (sm8250.dtsi) reserved + * memory mappings which are different in this device. + */ +/delete-node/ &xbl_aop_mem; +/delete-node/ &slpi_mem; +/delete-node/ &adsp_mem; +/delete-node/ &spss_mem; +/delete-node/ &cdsp_secure_heap; + +/ { + model = "Xiaomi Mi Pad 5 Pro"; + compatible = "xiaomi,elish", "qcom,sm8250"; + classis-type = "tablet"; + + /* required for bootloader to select correct board */ + qcom,msm-id = <QCOM_ID_SM8250 0x20001>; /* SM8250 v2.1 */ + qcom,board-id = <0x10008 0>; + + chosen { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + framebuffer: framebuffer@9c000000 { + compatible = "simple-framebuffer"; + reg = <0x0 0x9c000000 0x0 0x2300000>; + width = <1600>; + height = <2560>; + stride = <(1600 * 4)>; + format = "a8r8g8b8"; + }; + }; + + battery_l: battery-l { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3870000>; + energy-full-design-microwatt-hours = <16600000>; + charge-full-design-microamp-hours = <4300000>; + }; + + battery_r: battery-r { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3870000>; + energy-full-design-microwatt-hours = <16600000>; + charge-full-design-microamp-hours = <4300000>; + }; + + bl_vddpos_5p5: bl-vddpos-regulator { + compatible = "regulator-fixed"; + regulator-name = "bl_vddpos_5p5"; + regulator-min-microvolt = <5500000>; + regulator-max-microvolt = <5500000>; + regulator-enable-ramp-delay = <233>; + gpio = <&tlmm 130 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + bl_vddneg_5p5: bl-vddneg-regulator { + compatible = "regulator-fixed"; + regulator-name = "bl_vddneg_5p5"; + regulator-min-microvolt = <5500000>; + regulator-max-microvolt = <5500000>; + regulator-enable-ramp-delay = <233>; + gpio = <&tlmm 131 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + + pinctrl-name = "default"; + pinctrl-0 = <&vol_up_n>; + + key-vol-up { + label = "Volume Up"; + gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <15>; + linux,can-disable; + gpio-key,wakeup; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* S6c is really ebi.lvl but it's there for supply map completeness sake. */ + vreg_s6c_0p88: smpc6-regulator { + compatible = "regulator-fixed"; + regulator-name = "vreg_s6c_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-always-on; + vin-supply = <&vph_pwr>; + }; + + reserved-memory { + xbl_aop_mem: memory@80700000 { + reg = <0x0 0x80600000 0x0 0x260000>; + no-map; + }; + + slpi_mem: memory@88c00000 { + reg = <0x0 0x88c00000 0x0 0x2f00000>; + no-map; + }; + + adsp_mem: memory@8bb00000 { + reg = <0x0 0x8bb00000 0x0 0x2500000>; + no-map; + }; + + spss_mem: memory@8e000000 { + reg = <0x0 0x8e000000 0x0 0x100000>; + no-map; + }; + + cdsp_secure_heap: memory@8e100000 { + reg = <0x0 0x8e100000 0x0 0x4600000>; + no-map; + }; + + cont_splash_mem: memory@9c000000 { + reg = <0x0 0x9c000000 0x0 0x2300000>; + no-map; + }; + + ramoops@b0000000 { + compatible = "ramoops"; + reg = <0x0 0xb0000000 0x0 0x400000>; + record-size = <0x1000>; + console-size = <0x200000>; + ecc-size = <16>; + no-map; + }; + }; +}; + +&adsp { + firmware-name = "qcom/sm8250/xiaomi/elish/adsp.mbn"; + status = "okay"; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>; + vdd-l2-l10-supply = <&vreg_bob>; + vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>; + vdd-l6-l9-supply = <&vreg_s8c_1p35>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; + vdd-l13-l16-l17-supply = <&vreg_bob>; + + /* (S1+S2+S3) - cx.lvl (ARC) */ + + vreg_s4a_1p8: smps4 { + regulator-name = "vreg_s4a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5a_1p9: smps5 { + regulator-name = "vreg_s5a_1p9"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <2040000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s6a_0p95: smps6 { + regulator-name = "vreg_s6a_0p95"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1128000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2a_3p1: ldo2 { + regulator-name = "vreg_l2a_3p1"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a_0p9: ldo3 { + regulator-name = "vreg_l3a_0p9"; + regulator-min-microvolt = <928000>; + regulator-max-microvolt = <932000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L4 - lmx.lvl (ARC) */ + + vreg_l5a_0p88: ldo5 { + regulator-name = "vreg_l5a_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6a_1p2: ldo6 { + regulator-name = "vreg_l6a_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + /* L7 is unused. */ + + vreg_l9a_1p2: ldo9 { + regulator-name = "vreg_l9a_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L10 is unused, L11 - lcx.lvl (ARC) */ + + vreg_l12a_1p8: ldo12 { + regulator-name = "vreg_l12a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L13 is unused. */ + + vreg_l14a_1p88: ldo14 { + regulator-name = "vreg_l14a_1p88"; + regulator-min-microvolt = <1880000>; + regulator-max-microvolt = <1880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L15 & L16 are unused. */ + + vreg_l17a_3p0: ldo17 { + regulator-name = "vreg_l17a_3p0"; + regulator-min-microvolt = <2496000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l18a_0p9: ldo18 { + regulator-name = "vreg_l18a_0p9"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + /* + * Remaining regulators that are not yet supported: + * OLEDB: 4925000-8100000 + * ab: 4600000-6100000 + * ibb: 800000-5400000 + */ + regulators-1 { + compatible = "qcom,pm8150l-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-l1-l8-supply = <&vreg_s4a_1p8>; + vdd-l2-l3-supply = <&vreg_s8c_1p35>; + vdd-l4-l5-l6-supply = <&vreg_bob>; + vdd-l7-l11-supply = <&vreg_bob>; + vdd-l9-l10-supply = <&vreg_bob>; + vdd-bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-name = "vreg_bob"; + regulator-min-microvolt = <3350000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + + /* + * S1-S6 are ARCs: + * (S1+S2) - gfx.lvl, + * S3 - mx.lvl, + * (S4+S5) - mmcx.lvl, + * S6 - ebi.lvl + */ + + vreg_s7c_0p35: smps7 { + regulator-name = "vreg_s7c_0p35"; + regulator-min-microvolt = <348000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s8c_1p35: smps8 { + regulator-name = "vreg_s8c_1p35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-name = "vreg_l1c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L2-4 are unused. */ + + vreg_l5c_1p8: ldo5 { + regulator-name = "vreg_l5c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c_2p9: ldo6 { + regulator-name = "vreg_l6c_2p9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c_2p85: ldo7 { + regulator-name = "vreg_l7c_2p85"; + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-name = "vreg_l8c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-name = "vreg_l9c_2p9"; + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10c_3p3: ldo10 { + regulator-name = "vreg_l10c_3p3"; + regulator-min-microvolt = <3296000>; + regulator-max-microvolt = <3296000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11c_3p0: ldo11 { + regulator-name = "vreg_l11c_3p0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pm8009-rpmh-regulators"; + qcom,pmic-id = "f"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vreg_bob>; + vdd-l2-supply = <&vreg_s8c_1p35>; + vdd-l5-l6-supply = <&vreg_bob>; + vdd-l7-supply = <&vreg_s4a_1p8>; + + vreg_s1f_1p2: smps1 { + regulator-name = "vreg_s1f_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2f_0p5: smps2 { + regulator-name = "vreg_s2f_0p5"; + regulator-min-microvolt = <512000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L1 is unused. */ + + vreg_l2f_1p3: ldo2 { + regulator-name = "vreg_l2f_1p3"; + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L3 & L4 are unused. */ + + vreg_l5f_2p8: ldo5 { + regulator-name = "vreg_l5f_2p85"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6f_2p8: ldo6 { + regulator-name = "vreg_l6f_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7f_1p8: ldo7 { + regulator-name = "vreg_l7f_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&cdsp { + firmware-name = "qcom/sm8250/xiaomi/elish/cdsp.mbn"; + status = "okay"; +}; + +&gpi_dma0 { + status = "okay"; +}; + +&gpi_dma1 { + status = "okay"; +}; + +&gpi_dma2 { + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + fuel-gauge@55 { + compatible = "ti,bq27z561"; + reg = <0x55>; + monitored-battery = <&battery_r>; + }; +}; + +&i2c11 { + clock-frequency = <400000>; + status = "okay"; + + backlight: backlight@11 { + compatible = "kinetic,ktz8866"; + reg = <0x11>; + vddpos-supply = <&bl_vddpos_5p5>; + vddneg-supply = <&bl_vddneg_5p5>; + enable-gpios = <&tlmm 139 GPIO_ACTIVE_HIGH>; + current-num-sinks = <5>; + kinetic,current-ramp-delay-ms = <128>; + kinetic,led-enable-ramp-delay-ms = <1>; + kinetic,enable-lcd-bias; + }; +}; + +&i2c13 { + clock-frequency = <400000>; + status = "okay"; + + fuel-gauge@55 { + compatible = "ti,bq27z561"; + reg = <0x55>; + monitored-battery = <&battery_l>; + }; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie0_phy { + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; + status = "okay"; +}; + +&pm8150_gpios { + vol_up_n: vol-up-n-state { + pins = "gpio6"; + function = "normal"; + power-source = <1>; + input-enable; + bias-pull-up; + }; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&qupv3_id_2 { + status = "okay"; +}; + +&slpi { + firmware-name = "qcom/sm8250/xiaomi/elish/slpi.mbn"; + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <40 4>; +}; + +&usb_1 { + /* USB 2.0 only */ + qcom,select-utmi-as-pipe-clk; + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "peripheral"; + maximum-spped = "high-speed"; + /* Remove USB3 phy */ + phys = <&usb_1_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_1_hsphy { + vdda-pll-supply = <&vreg_l5a_0p88>; + vdda18-supply = <&vreg_l12a_1p8>; + vdda33-supply = <&vreg_l2a_3p1>; + status = "okay"; +}; + +&ufs_mem_hc { + vcc-supply = <&vreg_l17a_3p0>; + vcc-max-microamp = <800000>; + vccq-supply = <&vreg_l6a_1p2>; + vccq-max-microamp = <800000>; + vccq2-supply = <&vreg_s4a_1p8>; + vccq2-max-microamp = <800000>; + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; + status = "okay"; +}; + +&venus { + firmware-name = "qcom/sm8250/elish/venus.mbn"; + status = "okay"; +};
Add support for Xiaomi Mi Pad 5 Pro, codename is xiaomi-elish. This commit brings support for: * ADSP/CDSP/SLPI/VENUS * Backlight * Battery fuel gauge * Framebuffer * PCIe0 * USB2.0 Note backlight driver (ktz8866) is waitting for upstreaming[1]. [1] https://lore.kernel.org/linux-leds/20230120155018.15376-1-lujianhua000@gmail.com Signed-off-by: Jianhua Lu <lujianhua000@gmail.com> --- Changes in v2: - Apply Konrad's and Krzysztof's suggestion. arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/sm8250-xiaomi-elish.dts | 617 ++++++++++++++++++ 2 files changed, 618 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts