| Message ID | 20230216125257.112300-8-brgl@bgdev.pl (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs | expand |
On 16.02.2023 13:52, Bartosz Golaszewski wrote: > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > Add two UART nodes that are known to be used by existing development > boards with this SoC. > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > --- > arch/arm64/boot/dts/qcom/sa8775p.dtsi | 31 +++++++++++++++++++++++++++ > 1 file changed, 31 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi > index eda5d107961b..ce5976e36aee 100644 > --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi > +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi > @@ -489,6 +489,21 @@ &clk_virt SLAVE_QUP_CORE_1 0>, > operating-points-v2 = <&qup_opp_table_100mhz>; > status = "disabled"; > }; > + > + uart12: serial@a94000 { > + compatible = "qcom,geni-uart"; > + reg = <0x0 0xa94000 0x0 0x4000>; The address part ought to be padded to 8 hex digits > + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; > + clock-names = "se"; > + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 Please use the bindings constants as pointed out in the previous replies. > + &clk_virt SLAVE_QUP_CORE_1 0>, > + <&gem_noc MASTER_APPSS_PROC 0 > + &config_noc SLAVE_QUP_1 0>; > + interconnect-names = "qup-core", "qup-config"; > + power-domains = <&rpmhpd SA8775P_CX>; > + status = "disabled"; > + }; > }; > > qupv3_id_2: geniqup@8c0000 { > @@ -524,6 +539,22 @@ &config_noc SLAVE_QUP_2 0>, > status = "disabled"; > }; > > + uart17: serial@88c000 { > + compatible = "qcom,geni-uart"; > + reg = <0x0 0x88c000 0x0 0x4000>; Ditto > + interrupts-extended = <&intc GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>, > + <&tlmm 94 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; > + clock-names = "se"; > + interconnects = <&clk_virt MASTER_QUP_CORE_2 0 > + &clk_virt SLAVE_QUP_CORE_2 0>, Ditto Konrad > + <&gem_noc MASTER_APPSS_PROC 0 > + &config_noc SLAVE_QUP_2 0>; > + interconnect-names = "qup-core", "qup-config"; > + power-domains = <&rpmhpd SA8775P_CX>; > + status = "disabled"; > + }; > + > i2c18: i2c@890000 { > compatible = "qcom,geni-i2c"; > reg = <0x0 0x890000 0x0 0x4000>;
diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi index eda5d107961b..ce5976e36aee 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi @@ -489,6 +489,21 @@ &clk_virt SLAVE_QUP_CORE_1 0>, operating-points-v2 = <&qup_opp_table_100mhz>; status = "disabled"; }; + + uart12: serial@a94000 { + compatible = "qcom,geni-uart"; + reg = <0x0 0xa94000 0x0 0x4000>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + clock-names = "se"; + interconnects = <&clk_virt MASTER_QUP_CORE_1 0 + &clk_virt SLAVE_QUP_CORE_1 0>, + <&gem_noc MASTER_APPSS_PROC 0 + &config_noc SLAVE_QUP_1 0>; + interconnect-names = "qup-core", "qup-config"; + power-domains = <&rpmhpd SA8775P_CX>; + status = "disabled"; + }; }; qupv3_id_2: geniqup@8c0000 { @@ -524,6 +539,22 @@ &config_noc SLAVE_QUP_2 0>, status = "disabled"; }; + uart17: serial@88c000 { + compatible = "qcom,geni-uart"; + reg = <0x0 0x88c000 0x0 0x4000>; + interrupts-extended = <&intc GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 94 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; + clock-names = "se"; + interconnects = <&clk_virt MASTER_QUP_CORE_2 0 + &clk_virt SLAVE_QUP_CORE_2 0>, + <&gem_noc MASTER_APPSS_PROC 0 + &config_noc SLAVE_QUP_2 0>; + interconnect-names = "qup-core", "qup-config"; + power-domains = <&rpmhpd SA8775P_CX>; + status = "disabled"; + }; + i2c18: i2c@890000 { compatible = "qcom,geni-i2c"; reg = <0x0 0x890000 0x0 0x4000>;