diff mbox series

[v2,6/7] remoteproc: qcom_q6v5_pas: Add support to attach a DSP

Message ID 20230306231202.12223-7-quic_molvera@quicinc.com (mailing list archive)
State Not Applicable
Headers show
Series remoteproc: qcom_q6v5_pas: Add support for QDU1000/QRU1000 mpss | expand

Commit Message

Melody Olvera March 6, 2023, 11:12 p.m. UTC 
Some chipsets will have DSPs which will have begun running prior
to linux booting, so add support to late attach these DSPs by
adding support for:
- run-time checking of an offline or running DSP via rmb register
- a late attach framework to attach to the running DSP
- a handshake mechanism to ensure full and proper booting via rmb

Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
---
 drivers/remoteproc/qcom_q6v5_pas.c | 103 ++++++++++++++++++++++++++++-
 1 file changed, 102 insertions(+), 1 deletion(-)

Comments

Bjorn Andersson March 16, 2023, 2:27 a.m. UTC | #1 
On Mon, Mar 06, 2023 at 03:12:01PM -0800, Melody Olvera wrote:
> Some chipsets will have DSPs which will have begun running prior
> to linux booting, so add support to late attach these DSPs by
> adding support for:
> - run-time checking of an offline or running DSP via rmb register
> - a late attach framework to attach to the running DSP
> - a handshake mechanism to ensure full and proper booting via rmb
> 
> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
> ---
>  drivers/remoteproc/qcom_q6v5_pas.c | 103 ++++++++++++++++++++++++++++-
>  1 file changed, 102 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/remoteproc/qcom_q6v5_pas.c b/drivers/remoteproc/qcom_q6v5_pas.c
> index 0871108fb4dc..e22be6a029a8 100644
> --- a/drivers/remoteproc/qcom_q6v5_pas.c
> +++ b/drivers/remoteproc/qcom_q6v5_pas.c
> @@ -242,10 +242,89 @@ static int adsp_load(struct rproc *rproc, const struct firmware *fw)
>  	return ret;
>  }
>  
> +static int adsp_attach(struct rproc *rproc)
> +{
> +	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
> +	int i, ret;
> +
> +	ret = qcom_q6v5_prepare(&adsp->q6v5);
> +	if (ret)
> +		return ret;
> +
> +	ret = adsp_pds_enable(adsp, adsp->proxy_pds, adsp->proxy_pd_count);
> +	if (ret < 0)
> +		goto disable_irqs;
> +
> +	ret = clk_prepare_enable(adsp->xo);
> +	if (ret)
> +		goto disable_proxy_pds;
> +
> +	ret = clk_prepare_enable(adsp->aggre2_clk);
> +	if (ret)
> +		goto disable_xo_clk;
> +
> +	if (adsp->cx_supply) {
> +		ret = regulator_enable(adsp->cx_supply);
> +		if (ret)
> +			goto disable_aggre2_clk;
> +	}
> +
> +	if (adsp->px_supply) {
> +		ret = regulator_enable(adsp->px_supply);
> +		if (ret)
> +			goto disable_cx_supply;
> +	}
> +
> +	/* if needed, signal Q6 to continute booting */
> +	if (adsp->q6v5.rmb_base) {
> +		for (i = 0; i < RMB_POLL_MAX_TIMES; i++) {
> +			if (readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
> +				writel_relaxed(1, adsp->q6v5.rmb_base + RMB_BOOT_CONT_REG);
> +				break;
> +			}
> +			msleep(20);
> +		}
> +
> +		if (!readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
> +			dev_err(adsp->dev, "Didn't get rmb signal from  %s\n", rproc->name);
> +			goto disable_px_supply;
> +		}
> +	}
> +
> +	ret = qcom_q6v5_wait_for_start(&adsp->q6v5, msecs_to_jiffies(5000));
> +	if (ret == -ETIMEDOUT) {
> +		dev_err(adsp->dev, "start timed out\n");
> +		qcom_scm_pas_shutdown(adsp->pas_id);
> +		goto disable_px_supply;
> +	}
> +
> +	return 0;
> +
> +disable_px_supply:
> +	if (adsp->px_supply)
> +		regulator_disable(adsp->px_supply);
> +disable_cx_supply:
> +	if (adsp->cx_supply)
> +		regulator_disable(adsp->cx_supply);
> +disable_aggre2_clk:
> +	clk_disable_unprepare(adsp->aggre2_clk);
> +disable_xo_clk:
> +	clk_disable_unprepare(adsp->xo);
> +disable_proxy_pds:
> +	adsp_pds_disable(adsp, adsp->proxy_pds, adsp->proxy_pd_count);
> +disable_irqs:
> +	qcom_q6v5_unprepare(&adsp->q6v5);
> +
> +	/* Remove pointer to the loaded firmware, only valid in adsp_load() & adsp_start() */
> +	adsp->firmware = NULL;
> +
> +	return ret;
> +}
> +
>  static int adsp_start(struct rproc *rproc)
>  {
>  	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
> -	int ret;
> +	int i, ret;
>  
>  	ret = qcom_q6v5_prepare(&adsp->q6v5);
>  	if (ret)
> @@ -304,6 +383,22 @@ static int adsp_start(struct rproc *rproc)
>  		goto release_pas_metadata;
>  	}
>  
> +	/* if needed, signal Q6 to continute booting */

Why does this come before the wait_for_start()? Is the DSP actually up
and running when you hit attach, or is it just loaded?

> +	if (adsp->q6v5.rmb_base) {

Afaict this is copy-paste from attach, please move it to a helper
function.

> +		for (i = 0; i < RMB_POLL_MAX_TIMES; i++) {
> +			if (readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
> +				writel_relaxed(1, adsp->q6v5.rmb_base + RMB_BOOT_CONT_REG);
> +				break;
> +			}
> +			msleep(20);
> +		}
> +
> +		if (!readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {

If you hit the break above, there should be no reason to read this
register again.

Seems cleaner to write this as:

	ret = readl_poll_timeout();
	if (ret < 0)
		goto release;

	writel(1, ...);

Regards,
Bjorn

> +			dev_err(adsp->dev, "Didn't get rmb signal from  %s\n", rproc->name);
> +			goto release_pas_metadata;
> +		}
> +	}
> +
>  	ret = qcom_q6v5_wait_for_start(&adsp->q6v5, msecs_to_jiffies(5000));
>  	if (ret == -ETIMEDOUT) {
>  		dev_err(adsp->dev, "start timed out\n");
> @@ -413,6 +508,7 @@ static unsigned long adsp_panic(struct rproc *rproc)
>  static const struct rproc_ops adsp_ops = {
>  	.unprepare = adsp_unprepare,
>  	.start = adsp_start,
> +	.attach = adsp_attach,
>  	.stop = adsp_stop,
>  	.da_to_va = adsp_da_to_va,
>  	.parse_fw = qcom_register_dump_segments,
> @@ -423,6 +519,7 @@ static const struct rproc_ops adsp_ops = {
>  static const struct rproc_ops adsp_minidump_ops = {
>  	.unprepare = adsp_unprepare,
>  	.start = adsp_start,
> +	.attach = adsp_attach,
>  	.stop = adsp_stop,
>  	.da_to_va = adsp_da_to_va,
>  	.load = adsp_load,
> @@ -728,6 +825,10 @@ static int adsp_probe(struct platform_device *pdev)
>  	if (ret)
>  		goto detach_proxy_pds;
>  
> +	if (adsp->q6v5.rmb_base &&
> +			readl_relaxed(adsp->q6v5.rmb_base + RMB_Q6_BOOT_STATUS_REG))
> +		rproc->state = RPROC_DETACHED;
> +
>  	qcom_add_glink_subdev(rproc, &adsp->glink_subdev, desc->ssr_name);
>  	qcom_add_smd_subdev(rproc, &adsp->smd_subdev);
>  	adsp->sysmon = qcom_add_sysmon_subdev(rproc,
> -- 
> 2.25.1
>
Melody Olvera March 20, 2023, 11:46 p.m. UTC | #2 
On 3/15/2023 7:27 PM, Bjorn Andersson wrote:
> On Mon, Mar 06, 2023 at 03:12:01PM -0800, Melody Olvera wrote:
>> Some chipsets will have DSPs which will have begun running prior
>> to linux booting, so add support to late attach these DSPs by
>> adding support for:
>> - run-time checking of an offline or running DSP via rmb register
>> - a late attach framework to attach to the running DSP
>> - a handshake mechanism to ensure full and proper booting via rmb
>>
>> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
>> ---
>>  drivers/remoteproc/qcom_q6v5_pas.c | 103 ++++++++++++++++++++++++++++-
>>  1 file changed, 102 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/remoteproc/qcom_q6v5_pas.c b/drivers/remoteproc/qcom_q6v5_pas.c
>> index 0871108fb4dc..e22be6a029a8 100644
>> --- a/drivers/remoteproc/qcom_q6v5_pas.c
>> +++ b/drivers/remoteproc/qcom_q6v5_pas.c
>> @@ -242,10 +242,89 @@ static int adsp_load(struct rproc *rproc, const struct firmware *fw)
>>  	return ret;
>>  }
>>  
>> +static int adsp_attach(struct rproc *rproc)
>> +{
>> +	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
>> +	int i, ret;
>> +
>> +	ret = qcom_q6v5_prepare(&adsp->q6v5);
>> +	if (ret)
>> +		return ret;
>> +
>> +	ret = adsp_pds_enable(adsp, adsp->proxy_pds, adsp->proxy_pd_count);
>> +	if (ret < 0)
>> +		goto disable_irqs;
>> +
>> +	ret = clk_prepare_enable(adsp->xo);
>> +	if (ret)
>> +		goto disable_proxy_pds;
>> +
>> +	ret = clk_prepare_enable(adsp->aggre2_clk);
>> +	if (ret)
>> +		goto disable_xo_clk;
>> +
>> +	if (adsp->cx_supply) {
>> +		ret = regulator_enable(adsp->cx_supply);
>> +		if (ret)
>> +			goto disable_aggre2_clk;
>> +	}
>> +
>> +	if (adsp->px_supply) {
>> +		ret = regulator_enable(adsp->px_supply);
>> +		if (ret)
>> +			goto disable_cx_supply;
>> +	}
>> +
>> +	/* if needed, signal Q6 to continute booting */
>> +	if (adsp->q6v5.rmb_base) {
>> +		for (i = 0; i < RMB_POLL_MAX_TIMES; i++) {
>> +			if (readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
>> +				writel_relaxed(1, adsp->q6v5.rmb_base + RMB_BOOT_CONT_REG);
>> +				break;
>> +			}
>> +			msleep(20);
>> +		}
>> +
>> +		if (!readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
>> +			dev_err(adsp->dev, "Didn't get rmb signal from  %s\n", rproc->name);
>> +			goto disable_px_supply;
>> +		}
>> +	}
>> +
>> +	ret = qcom_q6v5_wait_for_start(&adsp->q6v5, msecs_to_jiffies(5000));
>> +	if (ret == -ETIMEDOUT) {
>> +		dev_err(adsp->dev, "start timed out\n");
>> +		qcom_scm_pas_shutdown(adsp->pas_id);
>> +		goto disable_px_supply;
>> +	}
>> +
>> +	return 0;
>> +
>> +disable_px_supply:
>> +	if (adsp->px_supply)
>> +		regulator_disable(adsp->px_supply);
>> +disable_cx_supply:
>> +	if (adsp->cx_supply)
>> +		regulator_disable(adsp->cx_supply);
>> +disable_aggre2_clk:
>> +	clk_disable_unprepare(adsp->aggre2_clk);
>> +disable_xo_clk:
>> +	clk_disable_unprepare(adsp->xo);
>> +disable_proxy_pds:
>> +	adsp_pds_disable(adsp, adsp->proxy_pds, adsp->proxy_pd_count);
>> +disable_irqs:
>> +	qcom_q6v5_unprepare(&adsp->q6v5);
>> +
>> +	/* Remove pointer to the loaded firmware, only valid in adsp_load() & adsp_start() */
>> +	adsp->firmware = NULL;
>> +
>> +	return ret;
>> +}
>> +
>>  static int adsp_start(struct rproc *rproc)
>>  {
>>  	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
>> -	int ret;
>> +	int i, ret;
>>  
>>  	ret = qcom_q6v5_prepare(&adsp->q6v5);
>>  	if (ret)
>> @@ -304,6 +383,22 @@ static int adsp_start(struct rproc *rproc)
>>  		goto release_pas_metadata;
>>  	}
>>  
>> +	/* if needed, signal Q6 to continute booting */
> Why does this come before the wait_for_start()? Is the DSP actually up
> and running when you hit attach, or is it just loaded?

Yeah so DSP is loaded and partially booted, but it's waiting for a signal from our driver
to complete the boot process through to err_ready.

>
>> +	if (adsp->q6v5.rmb_base) {
> Afaict this is copy-paste from attach, please move it to a helper
> function.

Sure.

>
>> +		for (i = 0; i < RMB_POLL_MAX_TIMES; i++) {
>> +			if (readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
>> +				writel_relaxed(1, adsp->q6v5.rmb_base + RMB_BOOT_CONT_REG);
>> +				break;
>> +			}
>> +			msleep(20);
>> +		}
>> +
>> +		if (!readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
> If you hit the break above, there should be no reason to read this
> register again.
>
> Seems cleaner to write this as:
>
> 	ret = readl_poll_timeout();
> 	if (ret < 0)
> 		goto release;
>
> 	writel(1, ...);

That is much cleaner; I didn't know about the poll timeout function. Will rewrite using it.

Thanks,
Melody
>
> Regards,
> Bjorn
>
>> +			dev_err(adsp->dev, "Didn't get rmb signal from  %s\n", rproc->name);
>> +			goto release_pas_metadata;
>> +		}
>> +	}
>> +
>>  	ret = qcom_q6v5_wait_for_start(&adsp->q6v5, msecs_to_jiffies(5000));
>>  	if (ret == -ETIMEDOUT) {
>>  		dev_err(adsp->dev, "start timed out\n");
>> @@ -413,6 +508,7 @@ static unsigned long adsp_panic(struct rproc *rproc)
>>  static const struct rproc_ops adsp_ops = {
>>  	.unprepare = adsp_unprepare,
>>  	.start = adsp_start,
>> +	.attach = adsp_attach,
>>  	.stop = adsp_stop,
>>  	.da_to_va = adsp_da_to_va,
>>  	.parse_fw = qcom_register_dump_segments,
>> @@ -423,6 +519,7 @@ static const struct rproc_ops adsp_ops = {
>>  static const struct rproc_ops adsp_minidump_ops = {
>>  	.unprepare = adsp_unprepare,
>>  	.start = adsp_start,
>> +	.attach = adsp_attach,
>>  	.stop = adsp_stop,
>>  	.da_to_va = adsp_da_to_va,
>>  	.load = adsp_load,
>> @@ -728,6 +825,10 @@ static int adsp_probe(struct platform_device *pdev)
>>  	if (ret)
>>  		goto detach_proxy_pds;
>>  
>> +	if (adsp->q6v5.rmb_base &&
>> +			readl_relaxed(adsp->q6v5.rmb_base + RMB_Q6_BOOT_STATUS_REG))
>> +		rproc->state = RPROC_DETACHED;
>> +
>>  	qcom_add_glink_subdev(rproc, &adsp->glink_subdev, desc->ssr_name);
>>  	qcom_add_smd_subdev(rproc, &adsp->smd_subdev);
>>  	adsp->sysmon = qcom_add_sysmon_subdev(rproc,
>> -- 
>> 2.25.1
>>
diff mbox series

Patch

diff --git a/drivers/remoteproc/qcom_q6v5_pas.c b/drivers/remoteproc/qcom_q6v5_pas.c
index 0871108fb4dc..e22be6a029a8 100644
--- a/drivers/remoteproc/qcom_q6v5_pas.c
+++ b/drivers/remoteproc/qcom_q6v5_pas.c
@@ -242,10 +242,89 @@  static int adsp_load(struct rproc *rproc, const struct firmware *fw)
 	return ret;
 }
 
+static int adsp_attach(struct rproc *rproc)
+{
+	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
+	int i, ret;
+
+	ret = qcom_q6v5_prepare(&adsp->q6v5);
+	if (ret)
+		return ret;
+
+	ret = adsp_pds_enable(adsp, adsp->proxy_pds, adsp->proxy_pd_count);
+	if (ret < 0)
+		goto disable_irqs;
+
+	ret = clk_prepare_enable(adsp->xo);
+	if (ret)
+		goto disable_proxy_pds;
+
+	ret = clk_prepare_enable(adsp->aggre2_clk);
+	if (ret)
+		goto disable_xo_clk;
+
+	if (adsp->cx_supply) {
+		ret = regulator_enable(adsp->cx_supply);
+		if (ret)
+			goto disable_aggre2_clk;
+	}
+
+	if (adsp->px_supply) {
+		ret = regulator_enable(adsp->px_supply);
+		if (ret)
+			goto disable_cx_supply;
+	}
+
+	/* if needed, signal Q6 to continute booting */
+	if (adsp->q6v5.rmb_base) {
+		for (i = 0; i < RMB_POLL_MAX_TIMES; i++) {
+			if (readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
+				writel_relaxed(1, adsp->q6v5.rmb_base + RMB_BOOT_CONT_REG);
+				break;
+			}
+			msleep(20);
+		}
+
+		if (!readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
+			dev_err(adsp->dev, "Didn't get rmb signal from  %s\n", rproc->name);
+			goto disable_px_supply;
+		}
+	}
+
+	ret = qcom_q6v5_wait_for_start(&adsp->q6v5, msecs_to_jiffies(5000));
+	if (ret == -ETIMEDOUT) {
+		dev_err(adsp->dev, "start timed out\n");
+		qcom_scm_pas_shutdown(adsp->pas_id);
+		goto disable_px_supply;
+	}
+
+	return 0;
+
+disable_px_supply:
+	if (adsp->px_supply)
+		regulator_disable(adsp->px_supply);
+disable_cx_supply:
+	if (adsp->cx_supply)
+		regulator_disable(adsp->cx_supply);
+disable_aggre2_clk:
+	clk_disable_unprepare(adsp->aggre2_clk);
+disable_xo_clk:
+	clk_disable_unprepare(adsp->xo);
+disable_proxy_pds:
+	adsp_pds_disable(adsp, adsp->proxy_pds, adsp->proxy_pd_count);
+disable_irqs:
+	qcom_q6v5_unprepare(&adsp->q6v5);
+
+	/* Remove pointer to the loaded firmware, only valid in adsp_load() & adsp_start() */
+	adsp->firmware = NULL;
+
+	return ret;
+}
+
 static int adsp_start(struct rproc *rproc)
 {
 	struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
-	int ret;
+	int i, ret;
 
 	ret = qcom_q6v5_prepare(&adsp->q6v5);
 	if (ret)
@@ -304,6 +383,22 @@  static int adsp_start(struct rproc *rproc)
 		goto release_pas_metadata;
 	}
 
+	/* if needed, signal Q6 to continute booting */
+	if (adsp->q6v5.rmb_base) {
+		for (i = 0; i < RMB_POLL_MAX_TIMES; i++) {
+			if (readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
+				writel_relaxed(1, adsp->q6v5.rmb_base + RMB_BOOT_CONT_REG);
+				break;
+			}
+			msleep(20);
+		}
+
+		if (!readl_relaxed(adsp->q6v5.rmb_base + RMB_BOOT_WAIT_REG)) {
+			dev_err(adsp->dev, "Didn't get rmb signal from  %s\n", rproc->name);
+			goto release_pas_metadata;
+		}
+	}
+
 	ret = qcom_q6v5_wait_for_start(&adsp->q6v5, msecs_to_jiffies(5000));
 	if (ret == -ETIMEDOUT) {
 		dev_err(adsp->dev, "start timed out\n");
@@ -413,6 +508,7 @@  static unsigned long adsp_panic(struct rproc *rproc)
 static const struct rproc_ops adsp_ops = {
 	.unprepare = adsp_unprepare,
 	.start = adsp_start,
+	.attach = adsp_attach,
 	.stop = adsp_stop,
 	.da_to_va = adsp_da_to_va,
 	.parse_fw = qcom_register_dump_segments,
@@ -423,6 +519,7 @@  static const struct rproc_ops adsp_ops = {
 static const struct rproc_ops adsp_minidump_ops = {
 	.unprepare = adsp_unprepare,
 	.start = adsp_start,
+	.attach = adsp_attach,
 	.stop = adsp_stop,
 	.da_to_va = adsp_da_to_va,
 	.load = adsp_load,
@@ -728,6 +825,10 @@  static int adsp_probe(struct platform_device *pdev)
 	if (ret)
 		goto detach_proxy_pds;
 
+	if (adsp->q6v5.rmb_base &&
+			readl_relaxed(adsp->q6v5.rmb_base + RMB_Q6_BOOT_STATUS_REG))
+		rproc->state = RPROC_DETACHED;
+
 	qcom_add_glink_subdev(rproc, &adsp->glink_subdev, desc->ssr_name);
 	qcom_add_smd_subdev(rproc, &adsp->smd_subdev);
 	adsp->sysmon = qcom_add_sysmon_subdev(rproc,